Easy tips

Where is the high beam indicator?

Where is the high beam indicator? When you switch from low to high beams, you'll see the High Beam indicator turn on in the dash (it's a blue symbol that looks like a headlight). Is there a problem with the high beam indicator? No problem with low beams. Will post when I get a fix for the high beam indicator light. The high beam indicator gets power through the headlight. The LED lights won't complete the circuit. You would have to add a small light bulb or resistor between the red/white and red/green left headlight wires or red/blue and red/green...
Most popular

What causes a battery warning light to flicker?

What causes a battery warning light to flicker? Low Battery Power Another cause for a battery light to flicker is when your battery is nearly discharged, possibly caused by a malfunctioning alternator. The battery is one of the components to which your battery warning light is wired. When does the battery warning light go off? The battery warning light in your vehicle turns on when you turn the ignition key to the "on" position. As soon as you start the engine, the light goes off and remains off until you stop the engine again -- unless there's a problem. Why...
Easy lifehacks

How does a front defroster work in an air conditioner?

How does a front defroster work in an air conditioner? The front defroster uses the same blower motor, fan and venting system that the heating and air conditioning system use. Air passes through the heater core and then dry air that has been run through the air-conditioning evaporator is added to help remove the moisture from the windshield. What causes a defroster to become inoperable? Old Age: As defrosters age they can lose their conductivity which reduces their ability to conduct an electrical current. Repeated cleaning, the sun and objects rubbing over the grid will eventually wear the grid down...
Easy tips

Is the dome light on my Car working?

Is the dome light on my Car working? The main center bulb of the dome light does work, however (when opening the doors, etc.) I've checked the fuses and have yet to find a blown one. Fuse 601 is a 30amp and I'm not too sure how to check if it's gone bad. I know that this is the fuse for the delay and power windows. How can I tell if my dome lamp is working? Check a few of these other systems to see if they operate or if it's isolated to the radio and dome lamps. The ignition...
Easy lifehacks

What happens when you overcharge a condenser?

What happens when you overcharge a condenser? Excessive Condenser Heat Yet overcharging will greatly increase the temperature of the air being pushed out of your condenser unit. This heat stems from the higher operating temperatures of the refrigerant itself. A portion of it also comes from the overworked compressor motor inside of your condensing unit. Can a dirty condenser cause AC freeze up? Dirty coils can cause freezing because the layer of dirt on top of the coils can prevent them from absorbing the water fast enough. Bi-annual checkups from your local HVAC professional can keep your AC's coils clean....
Easy lifehacks

What are the trouble codes for an a solenoid?

What are the trouble codes for an a solenoid? The trouble codes related to this, the "A" solenoid, are codes P0750, P0751, P0752, P0753 and P0754 based on the specific malfunction that alerts the PCM to set the code and illuminate the Check Engine Light. These codes will also be associated to the A, B or C solenoid circuit. Do you need a solenoid valve for a fan clutch? Freon Pressure Switch, and N.C. Solenoid Valve are the only controls absolutely necessary for Fan Clutch operation. The N.C. Manual Switch, Air Pressure Switch, and Indicator Light are all optional controls...
Easy lifehacks

Which is better exhaust brake or engine brake?

Which is better exhaust brake or engine brake? When it comes to performance, the Jake brake is a lot more powerful compared to the exhaust brake. A Jake is to exert braking power that is slightly over the rated power output of the engine; in comparison, an exhaust brake can only do somewhere between 60 to 80 percent. What is the difference between exhaust brake and retarder? A retarder is a hydraulic or electromagnetic device fitted to the output of the transmission or on the driveshaft itself. An exhaust brake is a device that opens the exhaust valves at the...
Common questions

What causes a p0106 signal on a MAP sensor?

What causes a p0106 signal on a MAP sensor? A P0106 could be caused by: 1 Bad MAP sensor. 2 Water/dirt intrusion affecting MAP sensor connector. 3 Intermittent open in the reference, ground, or signal wire for the MAP sensor. 4 Intermittent short in the reference, ground, or signal wire for the MAP sensor. 5 Ground problem due to corrosion causing intermittent signal problem. What does the p0106 code on the OBD-II mean? If your OBD-II scanner identifies a P0106 code after checking, your manifold absolute pressure (MAP) sensor and barometric air pressure (BARO) sensor may be at fault. Address...
Most popular

What are the most common Dodge Ram transmission problems?

What are the most common Dodge Ram transmission problems? If so, you are experiencing some of the most common Dodge Ram transmission problems. We know how annoying it is to deal with transmission problems. Sometimes you’re going down the road and of all a sudden, the truck loses power. But forget about that! How much does it cost to replace a transmission on a Dodge Ram 1500? To replace a transmission, you should expect to pay all the way from $3,800 to $8.100. On the other hand, to repair a damaged transmission: it will cost about $1,800. But if you...
Easy tips

What should I do if I have an IPM / FCM fault?

What should I do if I have an IPM / FCM fault? IPM/FCM diagnosis and repair If playback doesn't begin shortly, try restarting your device. Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. Automotive diagnostics, electronics, fabrication, iRacing and much more! Why are there no traces on the IPM? The IPM is a very simple design consisting of only fuses and relays soldered onto its internal circuit boards. It has no logic chips, no memory. Due to a poor case design,...