Common questions

What kind of car is 2014 Ram 1500?

What kind of car is 2014 Ram 1500? Autotrader has 2,440 Used RAM 1500 cars for sale, including a 2014 RAM 1500 4x4 Crew Cab Laramie, a 2014 RAM 1500 4x4 Crew Cab Longhorn, and a 2014 RAM 1500 4x4 Crew Cab Sport. Are there any used Ram 1500s for sale? Autotrader has 2,989 RAM 1500 cars for sale, including a Used 2014 RAM 1500 4x4 Crew Cab Laramie, a Used 2014 RAM 1500 4x4 Crew Cab Laramie Longhorn, and a Used 2014 RAM 1500 4x4 Crew Cab Longhorn. Is there an extended warranty for RAM radio? Extended warranties are...
Other

Is it normal for a water pump to overheat?

Is it normal for a water pump to overheat? Overheating the water pump is not expected for us. It will be a prime concern if a water pump becomes overheated. Sometimes, due to a prime loss, the pump's water and the pump casing can get extremely hot. A small air leak in the suction line can because of unusual pump heating. What happens when you replace your water pump? Overheating after replacing water pump, thermostat and co... Q: Overheating after replacing water pump, thermostat and coolant temp. Sensor I was driving my truck one day and noticed that the temp...
Most popular

What happens if your windshield washer nozzle is broken?

What happens if your windshield washer nozzle is broken? When you operate a nozzle sprayer switch, there should be washer fluid spraying out onto the windshield. If a washer nozzle is broken, then the washer fluid will not spray a hard mist but rather come out like a running faucet hose with no restrictions. How can I tell if my windshield washer motor is malfunctioning? Use a raytek gun to check the temperature of the nozzle. The nozzle should heat up as the washer fluid is spraying out of it. If the windshield washer nozzle continues to malfunction after replacing...
Common questions

What should intake manifold bolts be torqued to?

What should intake manifold bolts be torqued to? Intake manifold bolts on SBC engines should be torqued to 30 lb-ft in a two-step sequence. First time around, set your torque wrench to 20, follow the pattern, then repeat the pattern (image above) again after setting the wrench to 30. The image above shows the torque pattern to be used when reinstalling the heads on any SBC engine. What are the torque specs for SBC engines? Intake manifold bolts and head studs/bolts have to be torqued in a certain pattern and to a certain torque spec in order for your engine...
Easy tips

How long does it take a locksmith to make a transponder key?

How long does it take a locksmith to make a transponder key? Creating a car key will take anywhere from 10 to 30 minutes, depending on the type of key and complexity of the transponder system. In rare cases where your locksmith does not have a blank key in stock, rest assured that they can order it for you and provide a spare set as soon as possible. Can you replace a transponder key on a Chrysler? If the Chrysler car key replacement is a transponder key, then it will have to be programmed and paired with your specific Chrysler...
Common questions

What is the advantage of a 3 cylinder engine?

What is the advantage of a 3 cylinder engine? A 3 cylinder engine is much more fuel efficient compared to a 4 cylinder engine of the same size. This is because of two primary factors, reduced frictional losses and lighter weight. Since there is one cylinder less, the frictional losses caused by metal surfaces coming in contact within the engine block is lesser. How much horsepower does a 3.0-liter engine have? The 3.0L LFW engine delivers a market-leading balance of specific output, high torque over a broad rpm band, fuel economy, low emissions and first-rate noise, vibration and harshness control....GM...
Easy lifehacks

How do you program a 2006 Dodge key?

How do you program a 2006 Dodge key? 2006 Dodge Ram 1500 Remote ProgrammingPress and hold UNLOCK button.After holding the UNLOCK button for a at least 4 seconds, continue holding the UNLOCK button and also press PANIC button within 6 seconds.Ensure acoustic signal is emitted indicating programming mode active.Release both buttons. How much does it cost to replace a 2006 Dodge Charger key? Hear this out loudPauseIn short, replacing a Dodge Charger key can cost between $50 to $350. How to program a keyless entry remote for a Dodge truck? Below are the programming instructions for the keyless entry remote...
Easy tips

Does a 12 valve Cummins need a computer to run?

Does a 12 valve Cummins need a computer to run? All 12-Valves are non-electronic injection pump engines and DO NOT require any electronics from the truck to run. Is the Cummins 12 valve engine unkillable? No diesel engine on earth is as legendary as a 12-valve Cummins. Not only is the inline-six known for its awesome stock torque figures, but the 1,100 pound iron hulk from Columbus, Indiana has a reputation for being almost literally unkillable, even after it’s been modified to produce prodigious power figures. Where did the Cummins 6 valve engine come from? He went on to say...
Most popular

Can shocks cause death wobble?

Can shocks cause death wobble? Death wobble is often blamed on a failed steering stabilizer or shocks and struts. Worn tie rods, idler arm, track bar, wheel bearings, pitman arm, steering center link and shaft, ball joints, alignment and even tire pressure can combine to cause the death wobble. Is there a locking hub on a Ford 4WD? Locking Hubs – Yes on No? In the beginning, Ford used manual locking hubs on their 4WD vehicles. This required you to get out and physically turn a knob on the front wheel hubs to lock the wheel and the axle shaft...
Other

Can a bad O2 sensor cause a car to stall?

Can a bad O2 sensor cause a car to stall? Bad performance. Your car may misfire or experience hesitation and stalling. Most cars default to the factory air-to-fuel ratio if the oxygen sensor fails, which can cause problems because of non-standard temperature, moisture, or air composition. How does an O2 sensor work in a catalytic converter? You can also check exhaust backpressure ahead of the converter by connecting a pressure gauge to the EGR exhaust port, an O2 sensor port, or an exhaust manifold air line connection. More than 1.25 psi of backpressure at idle, or more than 3 psi...