Easy tips

Elevating Your Interior with Panels for the Walls: Triodoors’ Exclusive...

Most popular

New Vodka Trends to Watch Out For

Easy tips

Experience the Stress-Free Benefits of Online Divorce!

Easy tips

5 Best Workable Tips How to Choose Essay Writing Service

Easy lifehacks

VR For Athletes and Spectators

Most popular

Transformative Tech Trends

Easy lifehacks

2022 World Cup: No Cable, No Problem!

Most popular

How Blockchain Technology Will Change Customer Experience

Easy lifehacks

Six Esports Leagues Pro Gamers Can Check Out

Most popular

Five New Trending Technologies to Look Out for in 2023

Other

What transmission is in my 65 Mustang?

What transmission is in my 65 Mustang? The 1965 Mustang used a Ford 2.77 Toploader 3-speed in the 170 and 200 Six engines and used the Ford 3.03 Toploader behind the V8 equipped cars. The Borg-Warner T10 or Ford T & C Toploader were used in all 4-speed applications. The tried and true Ford Cruise-O-Matic was used in all automatic transmission applications. How fast does a 1965 Mustang go? These updates amounted to 306 horsepower at 6,000 rpm – enough for a top speed of 138 mph and a 0-to-60 mph time of 6.6 seconds. What kind of transmission did...
Easy tips

How much HP does gt40 heads add?

How much HP does gt40 heads add? RE: WHATS THE HP GAIN STOCK TO GT40 HEADS you will need to find special headers to fit the 5.0 with the GT40P heads. Those heads can give you a decent 50 HP with a mild cam. What cam works best with gt40 heads? Stock H.O. cam with cobra roller rockers is a great combo with GT40 heads. The H.O. cam has a little better grind when combined with the 1.7 ratio cobra rockers giving you more hp/tq than the cobra cam setup. Are gt40 heads aluminum? They are cast iron. That's right,...
Easy lifehacks

Do fuel injection engines have spark plugs?

Do fuel injection engines have spark plugs? Modern engines with smart gasoline direct injection need spark plugs perfectly geared to the specific requirements of each combustion chamber. What happens when a fuel injector is faulty? Engine vibrates – When a fuel injector is faulty, the corresponding cylinder will be affected, and thus, it won’t be capable of firing. What this means is that while in motion, your engine is likely to hiccup, or vibrate in a bid to conclude each cycle without the needed fuel. What causes a spider fuel injector to misfire? This case study will help you to...
Common questions

How long and wide is a 68 Camaro?

How long and wide is a 68 Camaro? DimensionsExteriorLength :184.6 in | 4689 mm.Width :72.5 in | 1842 mm.Height :51.0 in | 1295 mm.Wheelbase :108.1 in | 2746 mm. What is the curb weight of a 1969 Camaro? FeaturesEngine Location :FrontDrive Type :Rear WheelProduction Years for Series :1967 - 1969Price :$2,635-$2,850Weight :3042 lbs | 1379.828 kg How much does a 1967 Chevy Camaro weigh? FeaturesEngine Location :FrontDrive Type :Rear WheelProduction Years for Series :1967 - 1969Price :$2,500-$3,310Weight :2800 lbs | 1270.059 kg What engines came in a 68 Camaro? Engine choices were plentiful, including the standard 230-cid six-cylinder, optional 250-cid...
Other

What was the price of the first Chevy truck?

What was the price of the first Chevy truck? With its combination of convenience features usually reserved for cars, a stylized fiberglass fenders, and Chevy’s then-new 283-cubic-inch V8 (the same engine found in the Corvette and Bel Air), the Cameo could arguably be called the world’s first sport truck. At $1,981, it wasn’t cheap when it was new. When did the value of a pickup truck increase? So imagine telling truck buyers between, say, 1946 and 1973 that their trucks would increase in value by over 1,000%. Living in the era where new luxury trucks sell for close to $70,000,...
Easy lifehacks

Why does my door lock make a noise?

Why does my door lock make a noise? Most power door locks operate using gears or motors that may quietly whir, or make noise when they operate. Those noises are normal. However, if the noise suddenly becomes louder or more pronounced, then this may be an indicator that the gears or motor are becoming worn out. The noises may get louder until the actuators eventually fail. 2. What are the symptoms of a bad door lock? 1. Unusual noises coming from inside the door. Unusual noises coming from inside the door are one of the first symptoms of a potential...
Common questions

When did the Chrysler 383 V8 come out?

When did the Chrysler 383 V8 come out? The Chrysler 383 V8 engine was first seen in 1959 and was produced up through 1971. This motor was one of Chrysler’s most widely used engines in the 60s and was found in a large amount of Chrysler, Dodge and Plymouth models. What kind of engine does a Mopar 383 have? The 383 B block, or "low block", has a 4.25" bore and 3.38" stroke. The 1966-1967 383 had a 10:1 compression ratio. The standard issue 4-bbl motor had 325 horsepower. In 1968 and 1969 there were two new high performance versions...
Easy lifehacks

What do you call a wheel hub assembly?

What do you call a wheel hub assembly? Also called a wheel hub bearing, hub assembly, wheel hub unit or hub and bearing assembly, the wheel hub assembly is a crucial part of your steering system contributing to the safe steering and handling of your vehicle. What are the symptoms of a worn wheel hub bearing? • Grinding when the vehicle is in motion. Typically, this means there is mechanical damage in a wheel-end system. Related to a bearing, it means a loss of integrity such as roller or raceway damage. The noise is normally heard when turning or when...
Easy lifehacks

How do you put Freon in a 2006 Chrysler Pacifica?

How do you put Freon in a 2006 Chrysler Pacifica? Start your car and put the A/C on the maximum cooling setting with the blower on "high." Empty the R134A can until you are at the correct pressure. If your refrigerant was very low, you may need a bit more than 1 can as a Chrysler Pacifica refrigerant capacity is 24oz for 2007-2008, and 19oz for 2004-2006. Where is the low pressure charger on a Chrysler Town and Country? Trace the thicker of the two lines from the rear of the compressor until you locate the low-pressure service port, a...
Most popular

How do you inspect a flexplate?

How do you inspect a flexplate? Hear this out loudPauseStart the engine and let it idle. Slide under the vehicle with a stethoscope, and place the stethoscope probe against the underside of the bell housing. Any noise emanating from the this region indicates a problem with the flexplate and/or torque converter-flexplate combination. Can you replace a flexplate? Hear this out loudPauseTo replace the flex plate the transmission needs to be removed, its a 7 hour operation and the flex plate seals and oils would be another $185 to $195. What happens when I replace my flex plate? Consequently, the teeth...