Most popular

How do you remove fuel lines from a gas tank?

How do you remove fuel lines from a gas tank? Remove the fuel lines. Use a wrench or hose clamps to slide the fuel lines off of the filter. Pop the lines off of the nozzles on either end of the filter. As you remove the lines, make sure to angle them toward the bucket or jar to catch any gas that drips. How do you get gas out of a fuel filter? Place a bucket or jar under the filter to catch fuel. When you detach the fuel lines from the filter, any gas remaining in the lines will...
Other

What happens if my axle nut is loose?

What happens if my axle nut is loose? The stub axle nut puts preload on the inner and outer bearings inner race and the spacer in between the two bearings. If that is loose, the bearings may walk in and out of the bearing housing in the trailing arm and stub axle as well. Trailing arm and stub axles may get damaged. What prevents the spindle nut from coming loose? There is a little pin that keeps the inner nut locked to the toothed washer. It helps prevent the bearing from getting loose, but the pin can break. Also, torque...
Easy tips

How much antifreeze does a 2000 Ford Ranger take?

How much antifreeze does a 2000 Ford Ranger take? The amount of coolant Your Ford Ranger will hold varies wildly depending on engine size and model year. The typical range is between 1.2 and 3.5 gallons, though it's possible that some larger engines will require more. What kind of antifreeze does a 2001 Ford Ranger take? The type of coolant the 2001 Ford Ranger uses is green silicate 50/50. You will come into many problems with an engine. What kind of antifreeze do you need for a Ford Ranger? What Type of Antifreeze and Coolant for Ford Ranger. How Much...
Other

How much is a starter for a Ford F100?

How much is a starter for a Ford F100? Shop AutoZone for Ford F100 Starter. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only Just because your Ford F-100 is a classic doesn’t mean it can’t benefit from any handy upgrades. Your F-100 starter motor is an essential part of your truck and is the component behind the entire ignition process. What to do if your starter drive gets spun out? If the starter drive gets spun out, there is a fix. First, you need to take the starter drive back off from the starter motor shaft. Slide the...
Easy lifehacks

What happens when a diesel injector fails in a car?

What happens when a diesel injector fails in a car? While in most cases these deposits may not lead to injector failure, they can build up enough to disrupt the fuel spray, which leads to less efficient fuel combustion. This is often observed by the vehicle operator as a noticeable loss in power or lost fuel economy. Is it possible to cause 3 injectors to fail? One mechanic mentioned that maybe bad fuel could have caused the 3 injectors to fail and recommended filling up with high octane fuel to “clean out” the injectors- is that a possibility/ good idea?...
Most popular

What is a TSB on a truck?

What is a TSB on a truck? From Wikipedia, the free encyclopedia. Technical Service Bulletins, or TSBs, document recommended procedures for repairing vehicles, issued by a vehicle manufacturer when there are several occurrences of an unanticipated problem. What is TSB number? 020 3284 1575 TSB Bank/Customer service What are Vehicle Technical Service Bulletins ( TSB )? What are vehicle technical service bulletins (TSB)? A technical service bulletin (TSB) is an advisory issued by an automotive manufacturer to its dealership service departments detailing a fix for a known concern or difficult repair. The bulletin is for informational purposes only. Where do...
Common questions

How do you reset the oil change light on a 2012 Ford Expedition?

How do you reset the oil change light on a 2012 Ford Expedition? Follow the instructions below to reset the Oil Change Required Light on your Ford Expedition:Turn the ignition key to the “ON” position. Press the SETUP button repeatedly until you see “OIL LIFE =% HOLD RESET = NEW” Press and hold the RESET button until “OIL LIFE SET TO 100%” is displayed. How do I reset the oil light on my Ford Expedition? Press and release the TRIP/RESET button to scroll through the menu items until “Hold Reset If New Oil” is displayed. Press and hold the TRIP/RESET...
Most popular

Where do I drill studs for wiring?

Where do I drill studs for wiring? Drill into Corners at an Angle Make sure there's at least 1-1/4 inches between the back face of the stud and the cable. Cover the face of the stud with a metal nail plate to protect the cable where the hole is closer than 1-1/4 inches to the face of the stud. How do you run wires between studs? When running cable along the length of studs or joists, keep the cable to the center of each, leaving a 1 1/4-in. minimum clearance on each side of the framing member. When running cable...
Other

How is lifter preload measured?

How is lifter preload measured? Wait a few minutes for the pushrod seat in the hydraulic lifter to move back to the neutral position. Carefully scribe a new line on both pushrods. Measure the distance between the two scribe marks, it represents the amount of lifter preload. What is valve preload? Procedure for a Hydraulic Cam & Lifters. Lifter preload is the distance the pushrod seat moves down away from the retaining lock. This specific amount of space allows hydraulic lifters enough space to move. Where is the Lash on a pre load valve? To attain the performance features designed...
Easy lifehacks

How to draw an automatic transfer switch wiring diagram?

How to draw an automatic transfer switch wiring diagram? Wiring Diagram/Schematic /A, V – Drawing No. - Amp, Service Entrance/Non-Service Entrance Automatic Transfer Switch Owner's Manual .. Refer to the SMM Owner's/Installation Manual for.Variety of generac amp automatic transfer switch wiring diagram. How do you install a wire transfer switch? Affix the transfer switch to the wall, using mounting screws. Pull the bundle of wires through the insulating tube. Trim 5/8 inch (1.59 cm) from the covering of each individual wire. Join the wires to the transfer switch referring to the labels created previously. What kind of wiring is needed...