Common questions

What is a PCM on a diesel truck?

What is a PCM on a diesel truck? A power-train control module, abbreviated PCM, is an automotive component, a control unit, used on motor vehicles. It is generally a combined controller consisting of the engine control unit (ECU) and the transmission control unit (TCU). The PCM commonly controls more than 100 factors in a car or truck. What is the fuse panel diagram for a Ford F350 diesel? F C F Apr 16, need diagram for fuse box - have a F35 HD diesel, no stop lights at PM about the Ford F Super Duty XL LB. Dec 4, Diagram,...
Easy tips

When do glow plugs turn on and off?

When do glow plugs turn on and off? Pre-start glow for about 30 seconds. Think of the lamp as a minimum suggested wait time before cranking. Once started the glow plugs turn back on until the coolant is up to some temperature (90F?) or the RPM exceeds 2500. When the temp AND rpm are both low the glow plugs are on. What is the trouble code for Ford glow plug? If it see too low a current draw, it sets a trouble codes P0671 – P0678. Alldatadiy.com and Eautorepair.net are professional-grade shop manuals—period. What should the voltage be on the...
Most popular

Why is the direction of my Ceiling Fan not working?

Why is the direction of my Ceiling Fan not working? Turn off the fan and wait for it to completely stop, then switch the fan rotation by flipping the direction switch. If there is still no air movement when you turn the fan back on, or it is very weak, your fan may have a failing motor or the pitch of the ceiling fan blades may be too flat. How is the best way to remove a ceiling fan? How to Remove Ceiling Fans. Follow these steps to disassemble and remove your old ceiling fan. Step 1 – Turn of...
Other

What is the ignition switch on a 1987 Ford Ranger?

What is the ignition switch on a 1987 Ford Ranger? The ignition switch is a small but essential component on your 1987 Ford Ranger. It allows you to start the vehicle using your key. Once inserted into the ignition cylinder, the key can be turned to five positions: Lock, Off, Run, Start and Accessory. How can I test my Ford Ranger ignition? Plug the electrical wiring into the new ignition switch. Reconnect the battery cables and turn the key in the ignition switch to test it for proper operation. If the ignition works properly and your Ford Ranger starts, turn...
Easy tips

Where is the valet switch on a car?

Where is the valet switch on a car? Typical locations for valet switch: Under the driver's side dash (mounted in the under-dash covering trim panel or wire-tied to a harness) Mounted in the driver's side kick panel. Mounted in the steering column plastic housing. How do you turn off the valet button? 1. Enter the vehicle & insert then turn the ignition key to the ON position. 2. On systems from the late 1990s and newer, using trial and error, press & hold the valet button 1-5 times for a second each time. On systems from the mid 1990s and...
Most popular

How do you replace a passenger side axle?

How do you replace a passenger side axle? Take the 17mm bolt you remove and thread it into the other side of the spindle. Then take a flat, thin piece of metal and insert it into the slot at the back. Then thread in the bolt more and more so it pushes against the piece of metal you used. Can a CV joint be replaced at a parts store? You'd then replace it and the boot, lubricate the new and old joint with fresh grease, reinstall and go. Nowadays it's difficult to find a CV joint for sale at a...
Easy tips

Why are the front brakes on my F150 dragging?

Why are the front brakes on my F150 dragging? Both front brakes on my 2008 F150 2wd are heating. I replaced pads, turned rotors, cleaned caliper slides and,installed new pistons and seals in calipers. My ABS light stays out. This has been a recur…  read more Chris (aka- Moose) Ford Technician Vocational, Technical or Trade School 34,605 satisfied customers Why do I need to replace my caliper on my F150? Your F150’s disk brakes use pistons to push the brake pad into the rotor. These pistons have a rubber seal around them. This seal can go bad and the piston...
Easy lifehacks

How does the starter switch on a car work?

How does the starter switch on a car work? Only one wire is needed to carry current to each component. The starter switch is usually worked by the ignition key. Turn the key beyond the 'ignition on' position to feed current to the solenoid. The ignition switch has a return spring , so that as soon as you release the key it springs back and turns the starter switch off. Where does the ground wire go on a starter? The motor Is grounded and runs if the car is push started. If starter has a ground then the only other...
Easy tips

Does a 1998 f150 have a chip in the key?

Does a 1998 f150 have a chip in the key? The chip is in the key. Does Ford f150 key have a chip? The 2001 Ford F-150's key is equipped with a computer or transponder chip for security purposes. The chip is unique to the vehicle's VIN and ignition and another key will be unable to start the vehicle, unless first progRammed. Does a 1999 f150 key have a chip? NOTE: This ignition key has a chip hidden inside of the plastic head. It is a part of your automobile security system to prevent theft. Therefore, you MUST get it...
Easy tips

Was 2011 a good year for F-150?

Was 2011 a good year for F-150? The 2011 Ford F-150 is an excellent all-around truck, and even more so this year thanks to its more powerful engine choices. What generation is 2011 F-150? Twelfth generation The twelfth generation of the Ford F-Series is a light-duty pickup truck that was produced by Ford from the 2009 to 2014 model years....Ford F-Series (twelfth generation)Twelfth generation Ford F-150 (P415)Width2009–2011: 78.9 in (2,004 mm) 2012–2014: 79.2 in (2,012 mm) SVT Raptor: 86.3 in (2,192 mm) What years did Ford put 6.2 in F-150? For the 2011 model year, the 6.2 L V8 was...