Easy lifehacks

How do you reset the throttle body on a 2005 Chrysler 300?

How do you reset the throttle body on a 2005 Chrysler 300? Registered Insert ignition key and turn to "ON" (not start). Wait for all idiot lights to go out. Slowly depress the accelerator pedal all the way to the floor. Slowly release the accelerator pedal until it's all the way back up. Turn the ignition key to "OFF". Start the engine. Is there a problem with the Hemi throttle? Any of the current crop of Hemi throttle bodies that does not follow precisely the commanded throttle position...will immediately set a diagnostic trouble code (DTC). similar situation but getting no...
Common questions

What to do if your door is not latching?

What to do if your door is not latching? If you have got a door that is not latching or it seems to latch but when you try to lock it and when you push on it it just pops open. First thing you want to check for is to make sure that it's lining up properly with the grooves here and this one it may be time for a new latch here. What to do if your convertible top goes down? Please follow these emergency bypass instructions to return the top to the UP (raised) position. hold the switch...
Easy tips

What sensor does the powertrain control module PCM use to monitor misfires?

What sensor does the powertrain control module PCM use to monitor misfires? Using the ignition system sensor the PCM can detect a misfire on most vehicles by monitoring variations in the speed of the crankshaft through the crankshaft position sensor. A single misfire will cause a subtle change in the speed of the crank. How is the p0304 code diagnosed and fixed? How is the P0304 Diagnosed and Fixed? 1 Setp1: Find Out if Other Codes Exist. This is a common first step in many diagnosis processes. 2 Setp2: Examine the Wires and Coils. The next step is to visually...
Most popular

What kind of rods are in a Chrysler 3.8L engine?

What kind of rods are in a Chrysler 3.8L engine? 3.8L: Chrysler used two cast rods, a 4448904 in the earlier engines and 4654356 from ’01 through ’06. The 0015 powdered metal rod with the cracked cap was used from ’07 through ’09. What's the knock sensor on a Chrysler 3.8L engine? The 4781511AA block that was introduced for the 3.8L in ’01 had the flat pad for the bolt-on oil filter adapter and a 10mm hole for the knock sensor. In ’04, it was replaced by the 4781511AB casting that had an 8.0mm hole for the knock sensor and...
Other

What does it mean when your car immobilizer is not working?

What does it mean when your car immobilizer is not working? If you press the unlock button on your car key fob and the car door does not unlock, this is a sign that your key fob is not communicating with the immobilizer system. Perhaps the battery in your key needs to be replaced or the immobilizer system itself is having issues. Can a bad immobilizer cause a bad alarm system? The alarm system in your vehicle is associated with the same security feature as your immobilizer. If you have a bad immobilizer, then you’ll likely have a bad alarm...
Easy tips

Can vacuum hose be repaired?

Can vacuum hose be repaired? Fortunately, it is easy to repair a vacuum hose with this problem and the hose will only be a few centimeters shorter once repaired. In some cases, you wont need any new parts to complete the repair, but if you do they are readily available and much cheaper than a new hose. Can you replace a vacuum hose? Once the clamps are removed, a vacuum hose is fairly easy to remove. Grab the end that was clamped and twist it. This will break it loose, and the hose should turn side to side freely. While...
Easy lifehacks

Is a 2006 PT Cruiser reliable?

Is a 2006 PT Cruiser reliable? The 2006 Chrysler PT Cruiser Reliability Rating is 3.5 out of 5. It ranks 11th out of 32 for all car brands. Is the 2006 Chrysler PT Cruiser a reliable car? The car never had a mechanical issue. We purchased our 2006 Cruiser with 13K miles on it 66 months ago, we now have 115K miles, we traveled all over the country on all kinds of roads. The Cruiser has been one of the most reliable cars we have owned. Only recurring problem, camshaft positioning sensor replaced twice since car went over 80K. Why...
Easy lifehacks

Where can I get a new serpentine belt for my Chrysler?

Where can I get a new serpentine belt for my Chrysler? An updated engine bracket and pulley assembly is available at your local Chrysler parts department. This job is not highly technical, but is time-consuming. You will have to take a lot of stuff off to gain access to the engine brackets retaining bolts. This may not be a very good driveway or do-it-yourself auto repair. Why does my serpentine belt keep popping off? Plus, an important tip for removing some pain when doing the job. The Chrysler Town and Country, Dodge Caravan and Voyager have a tendency to throw...
Most popular

Why is my car coolant evaporating?

Why is my car coolant evaporating? If by evaporating you mean that you have to often fill the cooling system up then there is a leak somewhere, either internally (into the engine) or externally or the radiator cap is not up to its job anymore. It could also be that the engine is constantly running too hot and forces the boiling water out. Can coolant evaporate from your car? Most vehicles will lose a little coolant over time due to evaporation from the reservoir. But a significant loss of coolant in a relatively short period of time usually signals a...
Other

Are there any 1997 Chevy 1500 headlights left in stock?

Are there any 1997 Chevy 1500 headlights left in stock? Only 5 left in stock - order soon. . . . Only 5 left in stock - order soon. . Only 12 left in stock - order soon. . Only 5 left in stock - order soon. What's the best way to remove a headlight? Refer to a service manual for instructions on removing the bulb, electronics, plugs, and any other components you can. Carefully remove the headlight housing and follow the removal strategy. Use a hairdryer to dry out the moist air without breaking the seal. Use a hairdryer...