Other

Where is the ignition switch on a GMC Sierra?

Where is the ignition switch on a GMC Sierra?

That is called the lock cylinder. The ignition switch typically sits directly behind the lock cylinder. It has three main functions. Power the Accessories- This should be what you get when you turn the key to the first position. This allows you to use the power windows, radio, and any other accessory that is equipped in your GMC Sierra.

How do you replace the ignition switch on a GM Truck?

Refer to Steering Column Trim Covers Replacement . With the key installed, turn the key to the RUN position. Install an allen wrench into the hole on top of the lock cylinder housing. Push down on the allen wrench to release the tab on the lock cylinder inside the lock cylinder housing.

What kind of ignition switch does a Silverado have?

My 2007 Silverado with an LH6 5.3 DOD motor has intermittent oil pressure issues. Alittle back story, the truck has 274k on the… I’ve changed the original belt driven radiator cooling fan in my GMC Sierra 2004 to an… Okay so last year my ignition locked up & wouldn’t let me turn the truck off.

What happens when you disconnect the ignition switch?

Disconnect the connector from the ignition switch. The gears between the ignition switch and the lock cylinder housing must be in the correct position. Failure to do so will cause a misalignment of the gears in the ignition switch and the lock cylinder housing, which may result in a NO START or BATTERY DRAIN.

Do you need a new ignition switch for a GMC Sierra?

It pays to inspect your ignition and purchase a new GMC Sierra 1500 ignition switch from AutoZone when needed. If someone attempted to break into your car or the crevices in the switch are jammed, you need a new ignition switch for GMC Sierra 1500.

How do you replace the ignition switch on a Silverado?

Start by inserting the two additional connectors in the harness connector (the one with the screw in the middle). Then, plug the connector in under the steering column and tighten the screw. Plug in the connector in the back of the fuze box to the left, and the small connector in the middle of the harness.

How do you install a new ignition switch?

The easiest way to re-install the switch is to rotate the key in the ignition to the “accessory” position (fully counter-clockwise). Then, rotate the gear on the top of the new ignition switch fully COUNTER-CLOCKWISE (as you are looking at it like it goes in the slot).

What are the symptoms of a bad ignition switch?

We’ve compiled some of the most common symptoms of a bad ignition switch . These include stalling issues, not starting, and no power to the radio or accessories. The Sierra’s ignition switch is not what your key goes into.

How to remove the ignition switch without a key?

How to Remove the Ignition Switch Without a Key. 1 Step 1. Turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder. Be sure to make the hole large enough 2 Step 2. 3 Step 3.

How to change ignition key cylinder on 99-02 Sierra?

If your replacing the cylinder your just gonna slide the new cylinder back in until it locks in place and walk all the steps backwards to get your truck back together. If you just need the code, get it off the cylinder and then slide it back in place as well and repeat all the steps backwards to get your column back together.

Start by inserting the two additional connectors in the harness connector (the one with the screw in the middle). Then, plug the connector in under the steering column and tighten the screw. Plug in the connector in the back of the fuze box to the left, and the small connector in the middle of the harness.

Is the ignition on my GMC Sierra working?

Your GMC Sierra light truck has impressive features such as LED lights, and digital remote control, but if your ignition isn’t working as it should, it’s hard to even start your car. It pays to inspect your ignition and purchase a new GMC Sierra 1500 ignition switch from AutoZone when needed.

Is there an easy fix for a GMC ignition switch?

This is one way to fix a very complicated electrical system in the Chevrolet and GMC cars and trucks. Some are easy fixes with loose or bad electrical connections. Others involve the ignition switch itself, and others involve one of the computers that the system communicates with when starting the vehicle.

Where to get ignition switch for Sierra 1500?

Look for affordable, easy-to-install Sierra 1500 ignition switches from our online assortment, and retrieve your items up at a convenient AutoZone location with our Same Day Store Pickup option. You can further benefit during any in-store visit with access to our handy Loan-a-Tool program for DIY installation.

This is one way to fix a very complicated electrical system in the Chevrolet and GMC cars and trucks. Some are easy fixes with loose or bad electrical connections. Others involve the ignition switch itself, and others involve one of the computers that the system communicates with when starting the vehicle.

How can I Fix my Chevy Silverado ignition?

Wedge a shim in the connection and secure the new connection with hot glue, silicon or any other glue that can be fairly easy to scrap off and remove if further maintenance is required. Replace the steering column cover and that’s how you fix the ignition in your GMC Sierra or Chevy Silverado 1500, 2500 and 3500. Loading…

The easiest way to re-install the switch is to rotate the key in the ignition to the “accessory” position (fully counter-clockwise). Then, rotate the gear on the top of the new ignition switch fully COUNTER-CLOCKWISE (as you are looking at it like it goes in the slot).

That is called the lock cylinder. The ignition switch typically sits directly behind the lock cylinder. It has three main functions. Power the Accessories- This should be what you get when you turn the key to the first position. This allows you to use the power windows, radio, and any other accessory that is equipped in your GMC Sierra.

Wedge a shim in the connection and secure the new connection with hot glue, silicon or any other glue that can be fairly easy to scrap off and remove if further maintenance is required. Replace the steering column cover and that’s how you fix the ignition in your GMC Sierra or Chevy Silverado 1500, 2500 and 3500. Loading…

What to do if your ignition key won’t turn?

On several occasions after vehicle is parked and shut off, ignition key is inserted to start vehicle and the key will not turn. Only known remedy is to pull hard on the steering wheel in a left or right rotation while turning key at same time to unlock an otherwise locked ignition/steering wheel.

Why does the steering wheel turn with the ignition key off?

If the steering wheel is turned with the ignition key in the off position, this may cause excessive pressure between the lock plate and lock pin. The next time the ignition key is rotated from the “Off” to the “On” position, it may be difficult or unable to be rotated.

Why does my Chevy Silverado not turn the ignition?

It’s just from the steering wheel locking and it make it hard to turn the ignition if the steering is turned a lot when it’s shut off. I only have it do this when I park the truck on the street since I turn the tires like you should be parking on a slight hill on the street.

What causes a GMC Sierra 1500 key to not turn?

What are common reasons my GMC Sierra 1500 key won’t turn? While there are a variety of reasons your GMC Sierra 1500 key won’t turn, the most common 3 are a binding steering column/lock, an ignition switch issue, or a problem with the ignition key.

What does the sensor do on a GMC Sierra?

A sensor tells the security system whether the key is in the ignition or not. This is a common feature in the GMC, Pontiac, Oldsmobile, Saturn, Chevrolet and other past and present GM brand vehicles. The wire, which is connected to that sensor, comes loose or corroded and needs to be secured or cleaned.

When do you know something is wrong with the ignition relay?

If nothing happens on your dashboard when you turn the key in the ignition lock, and you are sure that the car battery is charged – there is a big risk that something is wrong with the ignition relay. These issues need to be solved as soon as possible. Otherwise, you will be forced to travel without your car.

What causes no ignition, or dash lights when turning key?

Q: I have no ignition, or dash lights when turning key. All relays and battery are fine. Dash lights work when headlights are on. I’m thinking its some kind of electrical problem. I got it to start one time with the remote start. After that, nothing. I’ve tried jump box to be sure I have power.

We’ve compiled some of the most common symptoms of a bad ignition switch . These include stalling issues, not starting, and no power to the radio or accessories. The Sierra’s ignition switch is not what your key goes into.

How to replace the ignition switch on a GM car?

1. Insert ignition key and turn to the “ON” position. Do not attempt to start the engine. Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2.

What causes a GMC Canyon key to get stuck in ignition?

Key Stuck in Ignition Causes: GMC Canyon Parking Lock. All vehicles equipped with automatic transmissions have a lock that keeps the key from being removed from… Steering Lock. A lot of vehicles are equipped with a steering lock. This lock can bind the ignition switch and get the… Bad Key. Bent

What should I do if my GM security light is flashing?

Insert ignition key and turn to the “ON” position. Do not attempt to start the engine. Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2.

What to do if you lose your GMC Sierra key?

Generally speaking, you have three options: First, call an automotive locksmith that offers a mobile service for GMC Sierra cars. We can help you with this option. Second, have your car towed to an official dealer. Third, order a key online and have the dealer or locksmith cut and program it (if necessary) for you.

Why does my car not start when I put the key in?

Putting the key in the ignition switch and starting the car feels like second nature. However, if your car has ignition switch problems, you may not be able to start the car at all. Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems.

Can a unworn key turn an ignition cylinder?

Or, an unworn key may not turn a worn ignition cylinder, as they haven’t “worn together.” How To Fix It: The best way to do this is to get a new lockset, with new keys and a new cylinder. You might consider getting a matched lockset that includes the door and trunk cylinders.

What kind of car is a 2004 GMC Sierra 1500?

Description: Used 2004 GMC Sierra 1500 SLE with AWD/4WD, 8000lb Towing Capacity, Audio and cruise controls on steering wheel, 6ft Bed, Power Driver Seat.

What kind of engine does a GMC Sierra 1500 have?

Description: Used 2004 GMC Sierra 1500 Work Truck with Towing Hitch, Upgraded Engine, AWD/4WD, 8000lb Towing Capacity, Standard Cab. Only 109134 Miles! Delivers 20 Highway MPG and 16 City MPG! This GMC Sierra 1500 boasts a Gas V6 4.3L/262 engine powering this Automatic transmission.

What are the different ignition positions on a Chevy Silverado?

Your vehicle is equipped with four different ignition positions. To turn the engine off, stop your vehicle and shift into park, then turn your key in the ignition switch to the LOCK/OFF position by turning counterclockwise, or closest to you.

Where is the spring on a GM ignition key?

You have the tumbler section of the assembly that you purchased. The spring is not there. Most GM’s have a switch that attaches on the back of what you have and the spring should be in there.

Where is the four way control on a GMC Sierra?

If your vehicle has this feature, the four-way control is located on the outboard side of the seat. To increase or decrease support, press and hold the front or rear of the control. Let go of the control when the lower seatback reaches the desired level of support.

Where does the ignition key go on a Silverado?

I have a 2000 Silverado 1500 LS 4×4 with a 5.3. Automatic column shift with cruise. When I start the truck, the key will stay in the “start” position.

How does the ignition work on a Sierra Denali?

Push the key all the way in (1) and then rotate the key coun- ter-clockwise to the Lock/Off position (2). FOptional equipmentSee Driving and Operating in your Owner’s Manual. KEYED IGNITION SYSTEM (IF EQUIPPED) KEYLESS ACCESS SYSTEMF REMOTE KEYLESS ENTRY TRANSMITTER (KEY FOB)F

Author Image
Ruth Doyle