When to replace the steering gear on a Chevy Silverado?

When the gear starts to go bad, you may notice your truck veering to one side, excessive play in the steering, or you might hear a popping or grinding noise while turning. To replace the steering gear, you must first gain access your truck’s steering box. And before you can replace the steering box, you must remove the radiator fan.

What to do when your 4 wheel drive Jerks?

The easiest way to fix bind-up is by pulling over to the side of the road with two wheels firmly on the bitumen and the other 2 wheels on a slippery surface like grass, mud or sand. This allows the wheels to all spin at different speeds releasing the wind-up in the transmission box.

How do you remove a power steering box?

Disconnect the rubber line to the power steering box using a pair of channel pliers. To do so, squeeze the clamps together and pull the line straight out. The line will leak fluid, so be sure to have a drain pan ready. Disconnect the second, hard line to the power steering box. Use a wrench to loosen the nut, and then pull the line straight out.

How to change the power steering gear box?

Use a Motor FLush into the Power Steering PUMP.. Turn Engine on.. Let It FLOW and PUt one Quart of Cheap Power Steering Fluid. and Do it again.. Dump the Old Power Steering FLuid. Put a Prestone Power Steering Fluid. FInish..

What kind of steering gear does a 1988 Dodge truck use?

Does anyone know of steering gear differences (Ratio, or steering effort/steering gear torsion bar size) on the ’88–98 C/K trucks? Seems the same basic steering gear design is used on 1988–2000 vehicles including C/K pickups, Suburban, Blazer, Yukon, Tahoe, and even some Dodge Ram trucks, including 1/2, 3/4, and 1-ton vehicles.

What kind of steering gear does a 98 C / K truck use?

Perhaps a faster-ratio gear was used on some models. Does anyone know of steering gear differences (Ratio, or steering effort/steering gear torsion bar size) on the ’88–98 C/K trucks?

How can I change the steering ratio on my truck?

It will fix that. Your truck has a variable ratio box and a control valve at the pump that changes line pressure and changes the steering ratio. this stupid sensor goes bad and people rebuild their entire font ends and change boxes and pumps and then realize… HEY… Whats this thing on the pump and find out they could have saved a grand or more.

What kind of steering gear do I Need?

AutoZone has everything you need when it’s time to replace your power steering gear box, including components that are custom-made for your make and model. So, whether you’re looking for a Ford F150 gear box or a steering gear box for Camaro cars, you’re certain to find the perfect match.

What happens if your steering gear is worn out?

Your steering gear can also cause your vehicle to drift to one side if it’s excessively worn-out. Fortunately, AutoZone has the solution to all of your steering problems. AutoZone has everything you need when it’s time to replace your power steering gear box, including components that are custom-made for your make and model.

Is the power steering on my Silverado working?

4 years later… Thank God for this place…..My 03 Silverado is acting up. Power Steering Fluid level is fine, hard to turn and it’s weak at low rpm/idle situations… but only when the steering was turned a bit. Seems to act up more when making a slow, low idle, left turn.

How do you replace a power steering input shaft?

Install the four bolts connecting the bearing on the steering gear. Make sure to torque correctly to the manufacturer’s recommendation. Install the face shield cover over the input shaft. Reinstall the gearbox onto the steering housing and reinstall onto the vehicle.

Where are the nuts in the steering box?

Those steering box and idler arm mounting bolts have a nasty secret. The nuts hiding inside the frame rails are not captured nuts, nor are they threaded bosses. They are free range hex nuts that will roll down inside the frame rail never to be seen again if allowed to escape.

What causes a steering box to go out?

Two or three on start up and stopping. Took it to front end place yesterday and they said steering box was shot and that they are notorious for going out and the bad part is they are under constant pressure lubrication so the failure is directly not attributable to poor lube maintenance.

When do you need a new steering box?

You may need to replace your steering box if you notice a grinding noise, burning oil smell, leaking power steering fluid, or have difficulty turning the steering wheel while driving. Don’t let a failing power steering gear box affect your safety on the road. Get a new steering gear box from O’Reilly Auto Parts.

Can a loose steering gearbox destroy a car?

A warning/disclaimer though. If done incorrectly this can destroy your steering gearbox. I know this from experience on a used vehicle I purchased about 20 years ago that had this adjustment done prior to me owning it.

How do you replace the steering box on a Chevy Silverado?

Disconnect the second, hard line to the power steering box. Use a wrench to loosen the nut, and then pull the line straight out. Remove the bolt on the coupler to the steering linkage. Remove the nut holding the Pitman arm to the steering box. Remove the Pitman arm using a Pitman arm puller.

When do I need to replace my steering gear box?

Your steering gear box transfers the steering wheel’s position to the steering linkage that turns the wheels. You may need to replace your steering box if you notice a grinding noise, burning oil smell, leaking power steering fluid, or have difficulty turning the steering wheel while driving.

Where can I get custom rebuilt steering gears?

Our family owned and operated businesses has proudly provided remanufactured steering gears and custom rebuilt steering gears that are better than new since 1980. Please call (800) 808-1148 for more information.

What kind of steering wheel do I need for a Silverado?

AmericanTrucks carries a wide selection of steering wheels available for you to purchase. These 99-06 Silverado steering wheels are designed to work perfectly with your truck and can replace your factory wheel, or even an aftermarket wheel that you already have.

Is the power steering still hard to steer?

Still having problem with my steering.. i have change the power steering gearbox, pitman, idler arm and where it connects to. i change alot of major part. and still hard to steer, specially when the engine is at IDLE.

When to replace the steering gear on a Chevy Silverado?