When to replace the serpentine belt on a Dodge Ram 1500?

While a serpentine belt setup is simple and easily maintained, an overlooked belt can leave you stranded if it breaks. Take a few moments to replace your old belt as it is one of the easiest maintenance items on your truck. This article applies to the 2nd generation Dodge Ram 1500 (1994-2001).

What kind of belt does a Dodge Ram use?

The development of the serpentine belt (sometimes referred to as a multi-rib or poly-v belt) has allowed engineers to not only reduce the amount of space necessary to drive the accessories, but to increase belt life.

Where is the wrench on a Dodge Ram?

Close-up of routing diagram for 3.9L, 5.2L, and 5.9L engines. On the passenger’s side of the engine, place your 15mm wrench or ratchet/breaker bar with a 15mm socket on the belt tensioner bolt.

When to replace belt on Dodge Ram 2500?

Replaced belt and tensioner on a 2006 Dodge Ram 2500 5.9. Tricky install but got it done. Removing the airbox helped create some space to reach the tensioner to remove and replace. I also removed the 2 nuts on the fan shroud on the bottom for better tool/arm access.

What does serpentine belt do on Dodge Ram?

A serpentine belt setup as used on the second generation Dodge Ram utilizes a tensioner to maintain proper belt tension and reduce the chances of belt slip on the accessory pulleys. Accompanied with low ratio pulleys, a serpentine belt setup improves fuel economy and reduces the load on the engine compared to a multi-belt setup.

Close-up of routing diagram for 3.9L, 5.2L, and 5.9L engines. On the passenger’s side of the engine, place your 15mm wrench or ratchet/breaker bar with a 15mm socket on the belt tensioner bolt.

How long does it take for a Dodge Ram belt to ship?

Usually ships within 6 to 10 days. . . . Only 1 left in stock – order soon. . Only 8 left in stock – order soon. . . . Only 17 left in stock – order soon. . Only 9 left in stock – order soon. . Only 16 left in stock (more on the way).

What’s the best way to replace a serpentine belt?

Auto tensioners have either a hole that will fit a half inch drive ratchet, or a bolt you can use a socket to apply pressure to. Insert the wrench or place the socket over the bolt on the tensioner and twist it away from the belt to relieve the tension on it.

What happens if the serpentine belt goes bad?

If the belt is worn enough to slip, it’s going to start wearing out faster. If it breaks, the broken belt could flip around in the engine compartment and potentially cause major damage to your vehicle. What Happens When the Serpentine Belt Goes Bad?

What to do if your serpentine belt breaks?

It’s possible you just need a new serpentine belt but the car has to be checked for seized components driven by the serpentine belt in case that accounts for the belt having broken in the first place. You can obtain a new serpentine belt by requesting serpentine belt replacement.

What happens when the power steering belt breaks?

You should notice the steering get better. If it still is hard to steer then you may need a new pump. Once the drive belt broke, the water pump and power steering pump (and all other accessories) stopped turning. If the engine got too hot due to the water pump not turning, coolant could have escaped, thus explaining the fluid (if it is coolant).

Is there an auto tensioner on a serpentine belt?

Most serpentine belts have an auto-tensioner that automatically keeps the proper tension on the belt. However, some belts have an adjustment screw that applies tension to the belt.

Why does my serpentine belt keep slipping on pulleys?

Serpentine belts stretch with age and use, but the tensioner is spring-loaded to keep the belt tight on the pulleys. If a belt starts slipping, the tensioner should always be checked to see if it is functioning properly.

What to do with a new Cummins belt?

Put your new belt in the tensioner with the SMOOTH SIDE AGAINST THE IDLER WHEEL and reinstall the tensioner.

How do I change serpentine belt on 2005 Dodge Ram 2500?

How Do I Change Serpentine Belt on 2005 Dodge RAM 2500 Diesel? The 2005 Dodge Ram has a serpentine belt that drives the engine accessories by supplying torque to their pulleys it gains from the crankshaft pulley. As the engine runs, the crankshaft spins, which turns the serpentine belt.

How to change the serpentine belt on a 6.7 Cummins?

To start, pop the hood and locate where the belt sits. It should be easy to find as it snakes around several components. Next, release the tensioner from the A/C pulley, then remove the airbox. Undo one bolt and release the tensioner. Rotate it clockwise to move it out of the path.

What’s the correct way to change the serpentine belt?

Undo one bolt and release the tensioner. Rotate it clockwise to move it out of the path. At this point, you can remove the old belt. Use the diagram to guide the new belt over each pulley. Leave the tensioner for last. It’s important to remember that there’s only one correct way to put the serpentine belt on.

How do you wrap a belt around a crankshaft pulley?

Wrap the new belt around the bottom of the crankshaft pulley by hand. Follow the belt routing diagram to route the belt around each of the accessory pulleys until only the tensioner pulley is left. Move the tensioner out of the way once more with the serpentine belt tool.

How do you remove a serpentine belt on a Cummins diesel?

I’ve applied tension to the tensioner with my 1/2″ drive socket and moved the ten. about 1/4″ according to my service manual but nothing seems to open up to allow for enough room behind the tensioner to remove the belt?

What kind of engine does a Dodge 1500 have?

USED 01 DODGE RAM 1500 5.2 318 LIFTOUT ENGINE PROJECT HOTROD 127k! Shipped 28330 (Fits: More than one vehicle) Only 1 left!

What should the lift be on a Dodge Ram?

You can get camshafts with a lift of up to .480″, but anything above .400″ will be ineffective without other upgrades and an upgrade to your truck’s computer. Alternatively you can purchase a set of 1.7″ roller rockers that will also improve lift while not requiring as many additional modifications. Figure 1.

What kind of engine does a Dodge Ram Van have?

Dealers can install such convenience features as a video player system and rear air conditioning. Either a 175-horsepower, 3.9-liter V-6 engine or a 235-hp, 5.2-liter V-8 can be installed in the 1500 series. Extended-wheelbase 1500 Vans also can have a 5.9-liter V-8 that generates 245 hp.

Where is the Dodge conversion van in California?

This Van Conversion is located in Los Angeles, California and is in good condition. She is also equipped with a Dodge engine that has 229,716 miles. This RV is in very good condition and systems are working well, according to her owner.

How many people can fit in a Dodge Ram Van?

Eight-passenger seating is standard on 1500 and basic 2500 models. The 2500 and 3500 versions can be equipped to seat 12, and the 3500 Maxi Wagon can have an extra seat in the fifth row to hold as many as 15 passengers.

Where can I buy a Dodge Ram belt?

Shop AutoZone for Dodge Ram 1500 Belt. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only

How big of a belt do I need to bypass the a / C pulley?

If you have A/C and are just trying to bypass the pulley this belt size is too small. After some trial and error I found you need a 90 inch interior belt. On my ’97 1500 the belt can bypass the A/C pulley without touching it, but that may be different on other models. I used the Duralast 900K7 belt at Autozone.

Shop AutoZone for Dodge Ram 1500 Belt. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only

When to replace a broken serpentine engine belt?

Using a gauge to check for belt wear (Image courtesy of tradetrucks.com) Have the belt replaced whenever a related component is replaced (a broken belt is often associated with a damaged or seized pulley on one of the engine accessories).

What are the consequences of a serpentine belt?

The serpentine belt is responsible for turning all of them. Consequences of a Worn Belt. The serpentine belt may not be prone to breaking, but it does wear out over time. When a serpentine belt wears – or if the belt becomes damaged or contaminated – the engine accessories may not be able to spin at the proper speed.

What happens if your serpentine drive belt breaks?

If it breaks, you’ll find that your driving experience is more than a little bit changed. Without this belt, your power steering pump won’t work, your A/C system won’t work, and even your alternator won’t operate. That means you’ll be running on battery power until the engine drains it, and then you’ll be stuck on the side of the road.

Where does the power come from in a serpentine belt?

The power for all of those things comes from the engine via the serpentine/drive belt. Most cars today have a single belt, called a serpentine belt. In the past, two or even three belts were used. The serpentine belt connects all the accessories on the engine to the main drive pulley, which is turned by the engine.

Where can I get a drive belt replacement?

The most popular service booked by readers of this article is Serpentine/Drive Belt Replacement. YourMechanic’s technicians bring the dealership to you by performing this job at your home or office 7-days a week between 7AM-9PM. We currently cover over 2,000 cities and have 100k+ 5-star reviews…

What kind of engine does a Dodge Ram have?

Beneath the stylish hood, there were several engine choices. Standard options were Magnum V6 or bigger V8 engines. With revised cam profile, modified valve train and addition of sequential electronic fuel injection, these engines delivered more power and better low down torque.

When did Ram get a 6.7 liter engine?

Most noticeable ones are the introduction of the common rail injection system in 2003, while in 2007 a newly designed 6.7 liter unit replaced the aging 5.9 liter engine. During 2006, Ram received a major overhaul, covering both interior and exterior.

What happens to a 5.2 liter Dodge Ram?

The Dodge 5.2 and 5.9 liter V8’s have their fair share of known issues that can prematurely end their lives. Cracked heads and engine blocks are quite common when mileage exceeds 100,000. Plenum leaks are also an issue, along with various check engine light codes.

The Dodge 5.2 and 5.9 liter V8’s have their fair share of known issues that can prematurely end their lives. Cracked heads and engine blocks are quite common when mileage exceeds 100,000.

Since the Ram uses the serpentine belt to rotate the water pump, when the belt breaks you are forced to come to a stop. This article applies to the Dodge Ram (2002-2008). The serpentine belt is made of a rubber compound and is grooved for optimal friction with the accessory pulleys.

Where do I find the serpentine belt routing diagram?

Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.

What do I need to replace serpentine belt on Dodge Ram?

Make sure the shielding around your wheels and engine is attached for full serpentine belt life. The procedure for the 5.7 Hemi engine differs from the 3.7/4.7 engines. For owners with the 5.7 liter engine, you will need a 3/8″ ratchet (preferably long-handled).

How much does it cost to replace a belt on a Dodge Ram 1500?

The average cost for a Dodge Ram 1500 serpentine belt replacement is between $122 and $136. Labor costs are estimated between $52 and $65 while parts are priced at $70. This range does not include taxes and fees, and does not factor in your specific model year or unique location.

How do you remove a serpentine belt from a car?

Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.

How do you install a serpentine belt on a water pump?

Begin the 4.7 and 3.7 serpentine belt installation by routing the belt around the alternator/generator pulley then under the water pump pulley. Now move it over the A/C pulley and down the outside of the tensioner.

What are the problems with a 2002 Dodge Ram 1500?

Lighting issues are common in Dodge Ram trucks and are one of the most frequently-cited 2002 Dodge Ram 1500 electrical problems specifically. Owners find that their headlights, taillights or turn signals suddenly stop working, causing irritation at best and a safety hazard at worst.

What kind of truck is the Dodge Ram?

All cars and minivans retained the Dodge nameplate, but the Dodge Ram and Dodge Dakota trucks became RAM trucks. This article focuses on the full size pickup formerly known as the Dodge Ram pickup and now known as the RAM pickup.

When to replace the serpentine belt on a Dodge Ram 1500?