Other

Is the water pump on my 2001 GMC LB7 Duramax leaking?

Is the water pump on my 2001 GMC LB7 Duramax leaking?

The water pump on my 2001 GMC LB7 Duramax had been leaking for some time – we’ll discuss the exact symptoms in a moment. I knew the pump had to be replaced, so I began accumulating the information I needed to do the job correctly. I wanted to know what parts were preferred and which ones should be avoided.

What should the pressure be on a Duramax water pump?

Normal cooling system pressure is in the range of 8-10 psi. The water pump’s coolant-side seal is there to contain this pressure against a spinning shaft. Over time, this seal will wear until it begins to leak coolant. That’s your cue for a need to install a new pump.

Why is my Duramax water pump leaking coolant?

The water pump’s coolant-side seal is there to contain this pressure against a spinning shaft. Over time, this seal will wear until it begins to leak coolant. That’s your cue for a need to install a new pump.

Is the ACDelco water pump properly machined?

The new ACDelco water pump is a marvel of modern manufacturing – and is beautifully machined. However, there is no evidence of heat treatment or of heat being used to properly fit the gear to the shaft. These gears are not threaded onto the shafts.

What kind of pump does a Duramax 6.6L use?

The BD-Power 1050651 R900 12MM CP3 Pump will increase performance in your 2001-2010 GM 6.6L Duramax. Featuring up to a 72% increase in capacity / displacement, this pump delivers enough fuel to support up to 750hp while maintaining 24,000psi of rail pressure.

What should I replace my Duramax CP3 pump with?

Replace the failing CP3 pump in your 2004.5-2005 GM 6.6L Duramax LLY or 2004.5-2005 GM 6.6L Kodiak/Topkick 4500/5500 with the Bostech HPP7308 Remanufactured CP3 Pump. Bostech CP3’s are remanufactured to stringent specifications. Each unit is 100% inspected and tested for quality and performance.

What kind of pump does a Duramax R900 use?

The R900 pump replaces the existing injection pump and simply bolts in place to produce up to 5.25 LPM versus the stock 3.05 LPM. Thats right, all that fuel without going to a dual pump system no extra pulleys, belts or pumps to install.

How can I Keep my Duramax Diesel pump healthy?

However, there are measures you can take to keep the pump happy and healthy, the first being to always buy your diesel from a high-traffic, reputable filling station that’s known to dispense good, clean fuel. Second, always change the fuel filter at or before the recommended service interval.

When to replace a Duramax water pump seal?

An overnight shutdown in cool weather should result in the upper radiator hose having little to no residual pressure. If the root cause of a water pump seal leak is due to overpressure, simply replacing the water pump will just buy you a little time.

What makes up a Duramax water pump cartridge?

As the lead-in photo and the above photos illustrate, the water pump actually consists of two primary components – the cartridge that includes the impeller and drive gear, and the outer housing that routes coolant both coming and going.

Is the Duramax water pump still corrosion resistant?

From a corrosion standpoint, all wetted surfaces involved with the water pump are as pristine as when they were first assembled more than 16 years ago. This means that Dex-Cool is vastlysuperior to any other coolant used by GM.

What should I do to my Duramax water pump?

Once you get the fan and cage out of the way its no different then the older duramax’s. Going by the book GM says to pull the starter and install the flywheel holding tool for breaking the balancer bolt loose and tightening it. This is where a lot of the excess time comes in.

What do you need to replace a Chevy water pump?

Here is the stuff you will need. Water pump: NAPA PN: WP58595 You dont have to buy a NAPA one but your local autoparts store can cross this number. Fan Clutch service tools. you will need to 47mm wrench, and the holder with pins.

How long is the water pump on a GM Truck?

I want to smack the GM engineer in the head who came up with that fan shroud design on the 2006+ trucks. That thing is the devil. Click to expand… Id rather punch the guy who clocked the one water pump housing fastener behind the balancer. Water pump would be a two hour job at most if it had been designed just a hair differently.

Do you have to pull starter on GM water pump?

Going by the book GM says to pull the starter and install the flywheel holding tool for breaking the balancer bolt loose and tightening it. This is where a lot of the excess time comes in. If you get the Lisle tool kit you can shave off an hour or better right there by not having to pull the starter.

I want to smack the GM engineer in the head who came up with that fan shroud design on the 2006+ trucks. That thing is the devil. Click to expand… Id rather punch the guy who clocked the one water pump housing fastener behind the balancer. Water pump would be a two hour job at most if it had been designed just a hair differently.

Once you get the fan and cage out of the way its no different then the older duramax’s. Going by the book GM says to pull the starter and install the flywheel holding tool for breaking the balancer bolt loose and tightening it. This is where a lot of the excess time comes in.

Going by the book GM says to pull the starter and install the flywheel holding tool for breaking the balancer bolt loose and tightening it. This is where a lot of the excess time comes in. If you get the Lisle tool kit you can shave off an hour or better right there by not having to pull the starter.

How much does it cost to replace water pump on Chevy Silverado?

Chevrolet Silverado 2500 HD Water Pump Replacement costs $432 on average. Following is a breakdown of the labor and parts estimates. What is a water pump and how does it work? The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley.

How long does it take to fix a water pump?

Alldata says 5.9 hours. Mitchell’s says 7.5 hours. Preparing correctly, it can be done in 4 hours. Dealer quote will most likely land in the $1100 parts and labor.

What kind of pump does a Duramax cp4.2 use?

Like all Duramax engines from ’01-’10, the LML was also void of a lift pump from the factory. This means that not only does the CP4.2 have to pressurize fuel as high as 29,000 psi before sending it to the rails, but it also has to pull its low pressure fuel from the tank.

The water pump on my 2001 GMC LB7 Duramax had been leaking for some time – we’ll discuss the exact symptoms in a moment. I knew the pump had to be replaced, so I began accumulating the information I needed to do the job correctly. I wanted to know what parts were preferred and which ones should be avoided.

The water pump’s coolant-side seal is there to contain this pressure against a spinning shaft. Over time, this seal will wear until it begins to leak coolant. That’s your cue for a need to install a new pump.

Author Image
Ruth Doyle