How to replace a Chevy Silverado heater blower motor?

The experts at 1A Auto show you how to replace a broken or failing blower fan blower motor on you 99-02 Chevy Silverado or Tahoe; or GMC Sierra or Yukon. step 1 :Remove Fan. Remove the four 7mm bolts securing the cover under the dash. Remove the 7/32 bolts securing the blower motor. Unplug the resistor.

How to replace the blower motor on a 2003 Chevy tracker?

Be careful of the courtesy light. Remove the blower moter and disconnect the purple/black power connector to it – – you’ll need this extra room to work with. 2 more screws, same size, 6.5mm on mine, 7or 8mm on some others, that holds the blower motor resistor in place. This replacement part is less than 40 bones at most parts store.

How to replace heater motor GMC Sierra 2500?

1 Remove the four 7mm bolts securing the cover under the dash 2 Remove the 7/32 bolts securing the blower motor 3 Unplug the resistor 4 Remove the three screws holding it in using your T25 torx bit or a 5/16 socket or a flat blade screwdriver 5 Pull it back toward the back of the car, down and out

Can a broken blower motor on a GMC Sierra be replaced?

The experts at 1A Auto show you how to replace a broken or failing blower fan blower motor on you 99-02 Chevy Silverado or Tahoe; or GMC Sierra or Yukon. Brought to you by 1A Auto.com– your source for quality replacement parts and the best service on the internet.

What to do if your Chevy blower motor relay blows out?

The blower motor relay on your Chevy vehicle is essential for the operation of the blower. If the relay is blown out, you will need to install a new one is soon as you can. Thankfully, it is fairly simple to tell if the relay is malfunctioning and to install a replacement.

Can a GM blower control switch be replaced?

This is no cause for concern since the circuit descriptions are the same for all of the GM vehicles covered by this repair tutorial. You don’t have to buy the whole A/C-Heater Control Panel to replace the blower control switch since the switch is removable. You can find the blower switch just about in anywhere.

Where is the HVAC controller on a Chevy Silverado?

Remove the panel under the driver side’s dash board (For passenger actuator remove the panel under the glove box). The actuators are mounted near the HVAC controller. Pry off the electrical harness plugged into the actuator. Unscrew the mounting screws and remove the actuator. Install your new actuator and tighten it down with the mounting screws.

Why does my Chevy Silverado blow hot air on one side?

This article applies to the Chevrolet Silverado (1999-Present). Does your Silverado blow hot air on one side and cold air on the other? If you have dual zone controls you may have run into this problem before. There is a way to fix this if you’re patient and willing to troubleshoot your way through it.

What happens to the climate control unit when the blower is off?

If the Blower is off, the Recirc door defaults to the fresh air position. The Recirc door actuator is closed when a ground is applied at Pin 4 of the Climate Control PCB. When Pin 4 is open the actuator opens the door allowing fresh air to flow into the cabin.

Why does the blower speed Hi stop working?

‘HI’ is the only blower speed that doesn’t depend on the blower resistor to function. When the blower motor resistor fails, 1 of the 3 or all 3 first speeds stop working. To explain this a bit further, this is due to the nature of how a resistor reduces the voltage that passes thru’ it by converting some of it into heat.

Is the inside cab blower on a 1995 Chevy Silverado?

Related Chevy Questions 1995 Chevy Silverado 1500 My inside cab blower is not 1995 Chevy Silverado 1500 My inside cab blower is not blowing and we replaced the blower relay And took the blower out and it works fine with no debris in it And I replace the fans with in the climate… read more

What to do if your Chevy heater stops working?

Describe your issueThe assistant will guide you Chat 1:1 with a chevy mechanicLicensed Experts are available 24/7 100% satisfaction guaranteeGet all the answers you need Ask Ron Z. Your Own Question Ron Z., – Chevy Tech – Category: Chevy Satisfied Customers:23,899 23,899 Satisfied Customers Experience: 18+yrs experience.

How do you replace a fan switch on a heater?

Replacing the fan switch begins by removing the knob. Most of the time the knob just pulls off, but sometimes it’s a little more tricky. Carefully inspect the knob all around using your inspection mirror to look underneath.

What happens when you change the fuse on a heater blower?

If the fuse is blown, replace it and then try the blower. If the fuse blows right away, your car may have a bad blower motor or some other problem in the system. If the blower works when you change the fuse, you may not be out of the woods yet. When the motor gets old and tired it will draw more current through the wires than a new motor.

Where is the blower motor on a 1998 Chevy c1500?

This 1998 Chevrolet C1500 came in with a no blower complaint. The starting place for testing is at the blower motor. The blower motor is located behind the passenger side of the dash and is accessed by removing the glove box. After opening the glove box there are two retainers that have to be dealt with.

Which is the best GMC heater blower motor?

Shop AutoZone for GMC C1500 A/C Heater Blower Motor. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only

How do you remove the cover on a blower motor?

To remove the cover over the blower motor the wires of course have to be disconnected. Then you have to release the upper and lower retainers. At the top, the cover has a slot in it that hooks over a flat pin. Lift up on the rear edge and lift the cover off of the flat pin.

How do you change a blower motor on a car?

Change the cabin air filter at this time if it is due for replacement, since you have easy access to the filter. Going headfirst into the footwell with a flashlight, look up until you locate the blower motor. Locate the three to six bolts keeping it in place, and remove with sockets and ratchet.

How much does it cost to replace a blower motor?

Motor type. Standard blower motors operate at a single speed and cost around $450 to replace, including parts and labor. Variable-speed motors cost $600 and up to replace.

How do you install a blower motor?

To install: Position the blower motor and install the mounting bolts. Attach the blower motor electrical connection. Connect the blower motor ventilation tube. Install the resistor and the glove box assembly. Install the right side instrument panel undercover panel. Connect the negative battery cable.

How much does an AC blower motor cost?

The costs to replace the furnace blower motor will depend on a few factors, including the type of blower motor required, the contractor you decide to hire and your geographical region. Based on these factors, the costs, including both parts and labor, can range anywhere from $250 to more than $500 for a standard single speed blower motor.

How to remove a heater core on a 1971 Chevy?

1970-72 Vehicles WITHOUT AIR CONDITIONING Drain the cooling system and disconnect the negative battery terminal. Remove the electrical connection at the blower. Remove the heater hoses at the core tubes. Remove the right front fender skirt. Remove enough screws so that the fender can be moved outward.

How do you reset a blower motor on a GM Truck?

However, you can reset the system by pulling the yellow 60 AMP VSES/ECAS fuse located in the under hood convenience center. After you remove the fuse you then start the truck and let it run for two minutes. Next shut it off and replace the fuse.

How much does it cost to change a blower motor?

In this case, the blower motor in my 2008 GMC Sierra Z71 4×4 (5.3L) stopped working completely. The price of a new blower motor at O’Reilly Auto parts was about $98.00. Installation was very simple. The cheapest local mechanic wanted almost $300 to do the same job. DO IT yourself….Hope this helps someone. Loading…