Most popular

What causes a Chevy Astro van to not start?

Table of Contents

What causes a Chevy Astro van to not start?

In the Chevy Astro van, power is supplied to the fuel pump by the the gray wire on the electrical connector when the engine is being cranked. If power is supplied, hitting the fuel tank with the flat side of a hammer while someone else is turning the ignition key to start will sometimes bump the fuel pump enough to allow it to start.

Where is the fuel pump on a Astro van?

If it is good, check for power at the fuel pump electrical connector located near the rear of the fuel tank on the driver’s side of the van. In the Chevy Astro van, power is supplied to the fuel pump by the the gray wire on the electrical connector when the engine is being cranked.

Where to check for no start fuel pump?

The first thing you want to do is check the fuse panel to see if the fuse is blown. If your car has two fuse panels than the one in the engine compartment; should be the correct one to check. The fuse panel or circuit box is usually located near the battery; and is a small black box with a removable lid.

Why is my GM fuel pump not working?

One of the things that can have you replacing a good fuel pump is an anti-theft system (PassLock) failure. How? This is due to the fact that when the Passlock system arms itself on your GM pickup or SUV, the engine will crank but won’t start, since the PCM has disabled the fuel injectors.

What to do if your starter doesn’t turn?

If battery voltage is present at the purple wire, and the starter doesn’t turn, replace the starter. If the voltage measurements at the starter are correct, and the starter cranks the engine over when the key is turned to the start position, proceed to the next step.

Why is my car not starting when I Turn on the ignition?

You pop into your garage in a hurry, but the car will not start when you turn on the ignition key. You can hear the starter spinning, but it’s not engaging with the flywheel. What could be wrong? Here is a more detailed list of the 5 most common causes why your starter won’t engage.

What does it mean when your car says no start?

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. If your vehicle is suffering a No Crank Condition, this tutorial may be a good starting point: How To Test The Starter Motor (GM 4.3L, 5.0L, 5.7L).

How to diagnose no start, turn key and nothing happens?

Spark (Only gas engines need a spark, diesel engines need high compression and glow plugs in cold weather to start) Compression (without compression the engine will not run, or not have any power) To read my article where I really lay out the FastC method of diagnosing any no start condition read here.

Why does my car not start when I turn the key?

There are a lot of ways the cars can not start. One of the most annoying ways is when you turn the key and nothing happens. Also, you may have just changed the battery and have no reason to believe it is bad.

Can a PassLock system failure cause a no start?

Passlock system failures are a very, very common cause of no start conditions. OK, the list of possible things that can go wrong looks pretty long but it is rare to see (or have) two different components go bad from two separate systems at the same time.

What should battery voltage be in Astro van?

A measurement of 12.5 volts is considered discharged, and the battery should be charged before any further testing. Any measurement below 11 volts indicates a severely discharged battery–the battery is most likely damaged and should be replaced. If the battery measures above 12.7 volts, proceed to the next step.

Where is the fuel pump fuse on a Astro van?

Check the fuel pump fuse located in the under-hood fuse block. If it is good, check for power at the fuel pump electrical connector located near the rear of the fuel tank on the driver’s side of the van. In the Chevy Astro van, power is supplied to the fuel pump by the the gray wire on the electrical connector when…

Why does my car not start when I Turn on the ignition?

The most common causes are in the ignition (for example, a bad ignition coil) or fuel system (for example, a clogged fuel filter). However, the source may also be a mechanical fault (for example, a leaking valve), or faulty components in other systems.

What is the fuse box on a Astro?

Cluster Illum, HVAC Controls, Chime Module, Radio Illumination, Rear Heat Switch Illumination, Rear Wiper/Washer Switch Illumination, Rear Liftgate Switch Illumination, Remote Cassette Illumination, O/H Console (Circuit Breaker) Power Door Lock Relay, 6-way Power Seat, Remote Control Door Lock Receiver, Dutch Door Module, Dutch Door Release

In the Chevy Astro van, power is supplied to the fuel pump by the the gray wire on the electrical connector when the engine is being cranked. If power is supplied, hitting the fuel tank with the flat side of a hammer while someone else is turning the ignition key to start will sometimes bump the fuel pump enough to allow it to start.

Check the fuel pump fuse located in the under-hood fuse block. If it is good, check for power at the fuel pump electrical connector located near the rear of the fuel tank on the driver’s side of the van. In the Chevy Astro van, power is supplied to the fuel pump by the the gray wire on the electrical connector when…

Cluster Illum, HVAC Controls, Chime Module, Radio Illumination, Rear Heat Switch Illumination, Rear Wiper/Washer Switch Illumination, Rear Liftgate Switch Illumination, Remote Cassette Illumination, O/H Console (Circuit Breaker) Power Door Lock Relay, 6-way Power Seat, Remote Control Door Lock Receiver, Dutch Door Module, Dutch Door Release

A measurement of 12.5 volts is considered discharged, and the battery should be charged before any further testing. Any measurement below 11 volts indicates a severely discharged battery–the battery is most likely damaged and should be replaced. If the battery measures above 12.7 volts, proceed to the next step.

What should temp be for Astro van to start?

Seems that van runs perfectly if temp is below 32 degrees or when no humidity when warmer. It has been raining about once a week and problem is back. Van is in garage and will start after a few days. I decided to put a ceramic heater near the front under carriage and the van started after a day.

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. If your vehicle is suffering a No Crank Condition, this tutorial may be a good starting point: How To Test The Starter Motor (GM 4.3L, 5.0L, 5.7L).

If it is good, check for power at the fuel pump electrical connector located near the rear of the fuel tank on the driver’s side of the van. In the Chevy Astro van, power is supplied to the fuel pump by the the gray wire on the electrical connector when the engine is being cranked.

Why does my car not start when I start it?

There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start…it’s because one of these components is missing from the mix.

This condition is usually due a failed fuel pump, a failed ignition coil, a failed ignition control module, a failed crank sensor, etc… that lets the engine crank (turn over) but does not let it start. A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine.

Why does my GM car say no start no crank?

How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.

How to troubleshoot a no start GM 4.3L pick up?

Testing a Cranks but Does Not Start condition on your GM 4.3L, 5.0L, 5.7L pick up, van or SUV is not that hard to do, if you have a solid diagnostic strategy. In this article I’ll show you the basics of testing such a problem.

Testing a Cranks but Does Not Start condition on your GM 4.3L, 5.0L, 5.7L pick up, van or SUV is not that hard to do, if you have a solid diagnostic strategy. In this article I’ll show you the basics of testing such a problem.

Can a bad check engine light be a bad TPS?

The check engine light will randomly turn on and off even if the car is running smoothly without any jerks and stalling. This is often the first ever symptom of a bad TPS. Using a code reader, you should be able to confirm whether a faulty TPS is the culprit or a different component.

If battery voltage is present at the purple wire, and the starter doesn’t turn, replace the starter. If the voltage measurements at the starter are correct, and the starter cranks the engine over when the key is turned to the start position, proceed to the next step.

What causes a Chevy truck to turn over but not start?

Plenty of turn over speed. With a test light there’s voltage at both sides of the coil but NO spark. Voltage at the throttle body injectors but NO fuel sprays. Fuel pump pumps. NO spark and NO fuel, turns fine. Rotor button turns, cap and rotor clean. Under the dash at the fuse panel there’s no voltage on the crank fuse.

Plenty of turn over speed. With a test light there’s voltage at both sides of the coil but NO spark. Voltage at the throttle body injectors but NO fuel sprays. Fuel pump pumps. NO spark and NO fuel, turns fine. Rotor button turns, cap and rotor clean. Under the dash at the fuse panel there’s no voltage on the crank fuse.

What causes a car to have a no start condition?

The engine pistons and valves (and all the other related components like: timing chains, etc.) are the ones responsible for the induction of the fresh air the engine needs for the combustion process. Although rare, internal engine mechanical problems can and do cause no-start conditions. Blown head gasket. Blown engine. 4.)

What does no start no crank no click mean?

If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that. In the old days, power flowed through the ignition switch and down to the starter solenoid. Not anymore.

How to test a no spark no start condition?

How To Test A Misfire / No Spark No Start Condition (at: easyautodiagnostics.com ). How To Test The Crank Sensor (GM 4.3L, 5.0L, 5.7L). How To Test The Camshaft Position Sensor Diagnostic Trouble Codes: P0340, P0341.

What’s the difference between no start and no crank?

It’s important to know that a no crank and a no start condition are not the same thing since this article only concentrates on testing a no start condition. In layman’s terms, a No Start Condition means that your vehicle’s starter motor is cranking the engine but the engine is not starting.

What does it mean when your car says no crank?

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. The most common problem, that causes this condition is a failed starter motor.

Why does my GM pickup engine not start?

How To Test The Fuel Pump On GM TBI Fuel Systems (for throttle body fuel injection fuel system equipped vehicles). A failure in one of the Passlock system’s components will cause the engine to start and then stall after a few seconds. This is due to the fact that the PCM, in your GM pickup or SUV, has disabled the fuel injectors.

Can a fuel pump cause a no start condition?

CASE 1: If your fuel pressure gauge read 50 PSI or more as the engine cranked. This means that the fuel pump on your 4.3L, 5.0L, or 5.7L is OK and not the cause of your No Start Condition. The next step is to observe the fuel pressure gauge’s needle (after your helper stopped cranking the engine).

How much psi does a fuel pump need to start?

The fuel pump produces much more than just 50 PSI of course.. but the bare minimum the engine needs to start is 50 PSI… so anything less and it will crank for ever before it starts or not start at all.

What should the fuel pressure be to start a Vortec engine?

The fuel system in your 4.3L, 5.0L, or 5.7L Vortec engine needs at least 50 PSI of fuel pressure to start. The fuel pump produces much more than just 50 PSI of course but the bare minimum the engine needs to start is 50 PSI… so anything less and it will crank for ever before it starts or not start at all.

How to check no fuel condition on GM 4.3L?

I’ve also included how to check a no fuel condition with starting fluid (although this is not the most effective way to test the fuel pump). It’s been my experience that misdiagnosing a bad fuel pump is a common occurrence on the 4.3L, 5.0L, 5.7L GM vehicles with the ‘Spider’ fuel injector assembly.

When did the Chevrolet Astro minivan come out?

The Astro and Safari were introduced for 1985 as the first minivan from General Motors. While marketed as a response to the first-generation Chrysler minivans, GM adapted a rear-wheel drive layout, sizing the Astro and Safari closely to the short-wheelbase Chevrolet G10 van.

When was the last time the Chevy Astro was made?

The Chevrolet Astro and GMC Safari twins were originally scheduled to be discontinued after 2002, but they soldiered on because of good sales; the last Astro and Safari rolled off the assembly line on May 13, 2005.

Where is the fuse for the fuel pump?

If the engine starts, the fuel pump is not supplying fuel or the ignition module is not pulsing the injectors. Check the fuel pump fuse located in the under-hood fuse block. If it is good, check for power at the fuel pump electrical connector located near the rear of the fuel tank on the driver’s side of the van.

If the engine starts, the fuel pump is not supplying fuel or the ignition module is not pulsing the injectors. Check the fuel pump fuse located in the under-hood fuse block. If it is good, check for power at the fuel pump electrical connector located near the rear of the fuel tank on the driver’s side of the van.

What causes a car to have no start?

If the TPS sensor sees closed throttle, but a high idle with matching MAF/Map signals, it flags the codes. That could have been caused by an open Pcv system or stuck open IAC valve. It could also be an electrical issue, but highly unlikely. Now we have the no start condition, which may or may not be caused by the repairs for the first issue.

What does it mean when your car won’t start?

An intermittent no-start condition references any time where starting is possible sometimes, and other times the engine will not start. This implies that the difference between starting and failure to start is not understood.

Why is my Chevy Silverado 1500 not starting?

However, today, when the truck will crank and start, the antitheft icon goes off after a few seconds with the key on and stays off while the truck is running. It never flashed either today or yesterday though. And I don’t know if the antitheft system disables cranking or starting or both.

What do you need to know about an Astro van?

Discuss things like air conditioning, refrigerant recharging, and dual climate controls, a/c vents, accumulator or defrosters, heater core, or fan inside the van. Discussion specific to electric components of vans.

How to change AWD fluid in Astro Safari?

First check tires for even wear and pressure, rotate/swap tires around. Second step is to replace the fluid with AT2, then do a bunch of figure 8s, put 50-100miles on it, and then replace the fluid again with AT2. Note that the clutch packs can hold the old fluid for several hundred miles.

Seems that van runs perfectly if temp is below 32 degrees or when no humidity when warmer. It has been raining about once a week and problem is back. Van is in garage and will start after a few days. I decided to put a ceramic heater near the front under carriage and the van started after a day.

The engine pistons and valves (and all the other related components like: timing chains, etc.) are the ones responsible for the induction of the fresh air the engine needs for the combustion process. Although rare, internal engine mechanical problems can and do cause no-start conditions. Blown head gasket. Blown engine. 4.)

What causes a car to not start with no gas?

Problem may be at wiring connector on top of fuel tank (hard to reach!). No gas in fuel tank (Check the fuel gauge, and keep in mind the gauge may not be reading accurately). Bad gas (Contaminated with water or too much alcohol or diesel fuel). If you just filled up with gas and now your car won’t start, suspect bad gas.

Why is my fuel tank not venting properly?

Make sure not to blow too much pressure into the tank since a leak from the fuel pump seal or from some other component could be created. If the tank is not venting properly it may actually swell when blowing air in through the hoses. It may be normal for the tank to expand a little and quickly contract when the air exits the tank.

Why does my gas pump shut off before I put gas in?

A very frustrating ordeal at the pump is to have the pump shut-off while putting gas in BEFORE the tank is full. Some vehicles even have the fuel splash back out due to improper vent tube operation.

Where does the water go in an Astro van?

The heating system on an Astro van starts at the water pump, where the water is picked up and transferred through a hose to the heater core. The water runs through the heater core and returns to the Astro’s intake manifold on the engine side of the thermostat housing.

Why does my 2001 Astro van not start?

by Lee Sallings. The three most common causes of a no-start condition in your 2001 Chevy Astro van are starting/charging system failure, ignition system failure and fuel system failure.

How to troubleshoot a no start GM 4.3L?

The following tutorial may be of help: How To Troubleshoot A No Start (GM 4.3L, 5.0L, 5.7L). CASE 3: The engine started and stayed running. This confirms that the fuel pump is starting to fail. The next step is to confirm the exact fuel pressure with a fuel pressure gauge to be absolutely sure.

What causes the fuel pump to not start?

The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.

What kind of car cranks but won’t start?

In this video we encounter a condition where a 2002 Chevy Silverado ( Similar to GMC Sierra ) pickup has a symptom of the engine cranks over but won’t start…. AboutPressCopyrightContact usCreatorsAdvertiseDevelopersTermsPrivacyPolicy & SafetyHow YouTube worksTest new features

In this video we encounter a condition where a 2002 Chevy Silverado ( Similar to GMC Sierra ) pickup has a symptom of the engine cranks over but won’t start…. AboutPressCopyrightContact usCreatorsAdvertiseDevelopersTermsPrivacyPolicy & SafetyHow YouTube worksTest new features

Why does my GM 4.3L engine not start?

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

It’s important to know that a no crank and a no start condition are not the same thing since this article only concentrates on testing a no start condition. In layman’s terms, a No Start Condition means that your vehicle’s starter motor is cranking the engine but the engine is not starting.

What’s the problem with my 1998 Chevy Venture?

1998 chevy venture, cut off yesterday while i was at a stop light and will not start back. It turns over but wont start. what is wrong. Im having similar problem Melissa I have replaced ALTETNATOR battery fuel pump all that goes wit them IM HAVING NEW STARTER INSTALLED as well as wat goes wit it..

What to do if your engine cranks but won’t start?

If so then that is where your problem is. 2004 ford e450 v10 class c motorhome…. cranks but won’t start…we have 1. Changed the crankshaft sensor 2. changed the PCM 3. Camshaft sensor 4. Replaced the fuel Pump 5. Replaced the computer (again) 6. changed the ignition switch 6. checked the Mass air flow sensor.

Where is the crank position sensor on a V6?

A fuse supplies 12 volts to the injectors, the ECM control the ground side. It depends on what engine you have. If you have the 3800 V6, then the crank position sensor behind the crankshaft pulley is most common. If you have the 3400 V6, most common is the ignition module.

What to do if your car won’t start after running out of gas?

Priming the fuel pump will remove any air that may have gotten into the lines as a result of the vehicle running out of fuel. If priming the fuel pump does not start the vehicle, I would recommend having a fuel system inspection performed by a qualified professional, such as one from YourMechanic.

Can a car start without priming with gas?

Engine wont start until you prime the throttle body with fuel, then it starts and runs great! Clicking this will make more experts see the question and we will remind you when it gets answered.

Why does my fuel pump not start when primed?

Q: Trouble starting unless I prime the fuel pump, turn off key and then prime again and start it. Trouble starting engine, I have to switch to “on” wait a few seconds, then back to “on” then finally turn the key to start engine. If I try to start normally, it would hold the idle and dies after a couple seconds or doesn’t crank over at all.

Priming the fuel pump will remove any air that may have gotten into the lines as a result of the vehicle running out of fuel. If priming the fuel pump does not start the vehicle, I would recommend having a fuel system inspection performed by a qualified professional, such as one from YourMechanic.

What makes a 1997 GMC C2500 no start?

1997 GMC C1500, C2500, C3500 Pick Up. 1997 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a misfire or a no-start problem (caused by the ignition coil, the ignition module, or the crankshaft position sensor).

Can a GM car still start with a misfire?

If you have one or just two readings that are under 90 PSI your GM vehicle will still start and run, albeit with a misfire condition. I’ve written a ‘How To Do a Compression Test’ article that you may find useful.

Author Image
Ruth Doyle