How do you change the steering pump on a Taurus?

How do you change the steering pump on a Taurus?

Rotate the belt tensioner clockwise using the ratchet and socket and slide the drive belt over the steering pump pulley. Refill the steering pump reservoir with new steering fluid and make sure the level is at the Full Cold mark. Turn on the engine and then turn the steering wheel from left to right five times.

How do you remove a power steering pump?

Place a drain pan under the vehicle to catch power steering fluid after you remove the two hoses from the steering pump. Detach the pressure hose from the steering pump by loosening the retaining nut with a flare wrench. Let the steering fluid drain into the drain pan.

How to attach a pulley to a power steering pump?

Attach the pulley to the new power steering pump using special tool 211-009 (T65P-3A733-C). See the Resources section below. Set the new steering pump in place and start the mounting bolts by hand using the ratchet extension if necessary. Then tighten the mounting bolts using the ratchet, ratchet extension and socket.

Do you need a power steering pump for a Taurus?

Taking corners in your Taurus shouldn’t be difficult. If your car squeals or whines in protest every time you turn the wheel, get back the smooth handling you used to enjoy with a replacement Ford Taurus power steering pump from AutoZone. Taurus power steering pumps need fluid to function.

Where is the power steering fluid located on a Ford Taurus?

The OHC-equipped Taurus uses a remote reservoir for the power steering fluid. This is located on the right side of the strut tower while the standard OHV model has the reservoir built into the pump housing. Check the fluid level by starting the engine and allowing it to warm up.

Do you need a new power steering pump?

If your car squeals or whines in protest every time you turn the wheel, get back the smooth handling you used to enjoy with a replacement Ford Taurus power steering pump from AutoZone. Taurus power steering pumps need fluid to function.

Why is my Taurus steering wheel not turning?

Taurus power steering pumps need fluid to function. When the fluid is low, it often indicates a leak, which makes it difficult to turn the steering wheel. Damage to the belt causes the same issue because the belt is connected to the engine and doesn’t work if it isn’t adjusted properly.

How do you replace a power steering pulley?

Anytime you install a new power steering pump and pulley, you need to install a new belt. The process for installing this unit is exactly opposite from the removal. Secure the pump to the engine block by screwing bolts through the bracket to the block. Tighten bolts before proceeding to recommended torque pressure.

What happens when a power steering pulley breaks?

This pressure is applied to the hydraulic fluid inside the lines that connects the pump to the steering gear box. When the power steering pump pulley is wearing out or has broken, it may display a few common warning signs that indicate service is needed.

How do you attach a power steering pump?

Unfasten the power steering pump mounting bolts using a ratchet, ratchet extension and socket and lift the pump off the engine compartment. Attach the pulley to the new power steering pump using special tool 211-009 (T65P-3A733-C). See the Resources section below.

When to replace the power steering pump on a Taurus?

by Dan Ferrell. The power steering pump provides for safe and easy handling of your Ford Taurus. Actuated under high pressure, the pump helps you steer the vehicle down the road. However, the control valve and other internal pump components wear down after years of service, and once the pump fails, you must replace it as soon as possible.

Attach a socket and ratchet to the bolt head on the end of the puller shaft. Turn the ratchet clockwise to draw the pulley off the power steering pump shaft. Place the power steering pump pulley squarely on the power steering pump shaft. Thread the pulley installer into the pump shaft until it bottoms out.

How does a power steering pump work on a Ford truck?

On a Ford light truck or car, it is pressed onto the power steering pump shaft. It is held on by friction, meaning no bolts or retaining clips hold the pulley onto the shaft. To remove the pulley from the power steering pump, a special power steering pump pulley puller is required.

How to replace power steering pump pulley in Chilton Ford?

Turn the nut on the installer shaft clockwise until the pulley is installed on the pump shaft. Unscrew the installer from the power steering pump shaft. Place the power steering belt over the pulley. Slide the power steering pump away from the engine and tighten the adjusting nut. “Chilton Ford Service Manual 2008 Edition Vol.