How do you change the brake pads on a Dodge Ram?
How do you change the brake pads on a Dodge Ram?
The calipers must be compressed back into the assembly. Using a C clamp or similar tool along with the old brake pad slowly compress the calipers. Open the brake fluid reservoir and make sure there is room in it for more fluid; compressing the calipers will result in fluid entering the reservoir.
What should I do when I Change my brake pads?
Commercial product to quieten brake squeal when changing brake pads. The clips holding the caliper assembly in place are also shown. To replace the brake rotor, the caliper must be removed as in the preceding section, as well as the bracket that surrounds the caliper.
How do you change the brake fluid on a Dodge Ram 1500?
Open the brake fluid reservoir and make sure there is room in it for more fluid; compressing the calipers will result in fluid entering the reservoir. Check periodically to make sure it is not running over. If needed, a clean rag can be inserted into the reservoir soaking up some of the fluid and remove it.
How do you replace the front brake caliper?
With the front brake caliper removed from the steering knuckle (see Step 2), remove the brake line from the caliper using a 3/8″ combination wrench or socket. Figure 8. Brake line removal. Install the the brake line into the new brake caliper.
How do you replace brake pads on a Dodge Ram?
Using a 3/8″ Allen (Hex) socket an ratchet or 3/8″ Allen wrench, remove the two socket head bolts securing the brake caliper to the steering knuckle. If planning to replace the brake calipers as well as brake pads, the brake line should be loosend prior to removing the caliper.
With the front brake caliper removed from the steering knuckle (see Step 2), remove the brake line from the caliper using a 3/8″ combination wrench or socket. Figure 8. Brake line removal. Install the the brake line into the new brake caliper.
What kind of brake system does Dodge Ram have?
This article applies to the Dodge Ram 1500 2nd Generation (1994-2001). In a world concerned with horsepower numbers, torque ratings, and towing capacities, we often forget about one of the most important systems on a vehicle: the brake system.
What should torque be on new brake pads?
Torque to 38 ft/lbs. After installing new pads on the front axle, several pumps of the brake pedal will be required to move the caliper pistons into position and restore proper brake pedal travel.
What kind of brakes does a Dodge Ram have?
Your Dodge Ram’s brakes tend to work a little harder than most average vehicles. You want to make sure the brakes are fresh so it can keep working just as hard. This article applies to the Dodge Ram (2002-2008). The brakes on your Dodge Ram tend to take quite a beating.
Where to replace the brake pads on a Dodge Ram 1500?
You can take the now-removed rotor to any auto parts supply store and someone at the store can turn the rotor or point you in the direction of someone that can do it for you. If they can’t turn it, then it should be replaced. Go ahead and pick up two as you will want to replace the other side as well.
Your Dodge Ram’s brakes tend to work a little harder than most average vehicles. You want to make sure the brakes are fresh so it can keep working just as hard. This article applies to the Dodge Ram (2002-2008). The brakes on your Dodge Ram tend to take quite a beating.
How do you remove the brake rotor from a Dodge Ram?
The only thing keeping it from being removed at this point is the brake caliper’s mounting bracket. There are two bolts that hold this bracket onto the steering knuckle. Once these are removed, you can remove the caliper mounting bracket, and finally remove the brake rotor. The brake rotor might take a few taps with a mallet to remove it.
Open the brake fluid reservoir and make sure there is room in it for more fluid; compressing the calipers will result in fluid entering the reservoir. Check periodically to make sure it is not running over. If needed, a clean rag can be inserted into the reservoir soaking up some of the fluid and remove it.
Are there disc brakes on 2nd generation Dodge Ram?
The rear brakes on the 2nd Generation Ram are of a drum design and are a bit more complex than contemporary disc brakes. Servicing of brake drums can be overwhelming for some, but do no fret as you can disassemble one drum assembly at a time while using the other as a guide.
What are the tools you need to change your brakes?
The Tools Needed to Change Brakes. 1 Start With the Right Protection. Before you start any project on your car, make sure that you are properly protected. You should have a pair of 2 Brake Pads and Rotors. 3 Jack and Jack Stand. 4 Lug Nut Wrench. 5 Brake Caliper Piston Tool.
What’s the best way to change brake pads?
A C-clamp — This will press on the caliper assembly and push the piston all the way in, resetting the brake once the new pads are in place. Note: Some vehicles will require the use of a special brake caliper tool to retract the brake caliper piston.
