Will a 429 bolt up to a C6 transmission?
Will a 429 bolt up to a C6 transmission?
The 351m, 400, 429, 460 all bolt up to the C6 transmission without any adapters.
What engines fit a C6 transmission?
The C6 was an automatic transmission used on engines such as the 351 Cleveland and the Ford 385 engines. Some well-known applications of the C6 transmission are the Ford Torino, Thunderbird and Mustang (This transmission has no relation the C6 Corvette).
What transmission goes with a 429?
Although the AOD and AODE are stout transmissions, for high-torque, big-block applications (429, 460, and up) the E4OD is the way to go because with Gearstar’s modifications this transmission is capable of handling 800-1,000 hp and all the torque that goes with big-block horsepower.
How does the 6R80 transmission work?
The transmission utilizes five clutch packs and a single one-way clutch to achieve six forward gear ratios, whereas earlier four speed units use six or more clutches/bands to achieve only four gears. 6R80 Transmission Ratios: 4.17, 2.34, 1.57, 1.14, 0.87, and 0.69:1.
What Fords came with a 460?
460
- Ford Thunderbird (1972-1976)
- Mercury Cougar (1974-1976)
- Ford/Mercury full-size (1972-1978)
- Ford/Mercury intermediate (1973-1976)
- Ford F-Series (1973-1998)
- Ford E-Series (1975-1996)
How to rebuild and modify Ford C4 and C6 automatic transmissions?
This Tech Tip is From the Full Book, HOW TO REBUILD & MODIFY FORD C4 & C6 AUTOMATIC TRANSMISSIONS. For a comprehensive guide on this entire subject you can visit this link: SHARE THIS ARTICLE: Please feel free to share this post on Facebook / Twitter / Google+ or any automotive Forums or blogs you read.
What should I do before installing a transmission?
Converter pump drive should be lubricated with transmission lube prior to installation to prevent seal damage. Install a new transmission mount in order to minimize movement around the driveshaft’s centerline. Also check driveshaft, universal joints, and slip yoke condition. Proper shifter adjustment is important to operation.
How big is a torque converter for a C4 transmission?
If a torque converter does not fit, do not force it. Most common flexplate sizes for C4 transmissions are 157-tooth (left) and 164-tooth (right). Each calls for its own bellhousing size.
What is the flexplate size for a C4 transmission?
Most common flexplate sizes for C4 transmissions are 157-tooth (left) and 164-tooth (right). Each calls for its own bellhousing size.
What kind of transmission do I need for a 429 Ford?
The C-6 is a good transmission choice to use for installing a 429 or 460 engine into earlier Ford models, too. The 31-spline output slip yoke required to hook your driveshaft to the C-6 is Ford part number C7SZ-4841A. This yoke accommodates either a Spicer 1330 series u-joint.
Can a C-6 transmission be installed on a V-8?
Replacement crossmembers are available to help you with the installation of the C-6 into 1955-’62 full-size Ford V-8s as well. The C-6 is a good transmission choice to use for installing a 429 or 460 engine into earlier Ford models, too.
How big is a Ford C 6 transmission?
Most donor cars will have an engine size over 351 cubic inches, up to 460 cubic inches; however, you will find some C-6 transmissions behind small-block Fords, especially in truck applications. Because of the C-6 transmission’s strength, you will find many of these units in four-wheel-drive applications.
This Tech Tip is From the Full Book, HOW TO REBUILD & MODIFY FORD C4 & C6 AUTOMATIC TRANSMISSIONS. For a comprehensive guide on this entire subject you can visit this link: SHARE THIS ARTICLE: Please feel free to share this post on Facebook / Twitter / Google+ or any automotive Forums or blogs you read.
