Where is the hub bearing on a Chevy Silverado?

Unless you’ve replaced a wheel hub bearing yourself, chances are you’ve never actually seen one. The wheel hub bearing is buried deep inside the wheel assembly of your Silverado, and it plays a big role in safety, but primarily handling and road-worthiness.

When to replace front wheel bearing Assy on 2500HD?

Replace Front Wheel Bearing Assy on 2500HD/3500SRW (dually similiar) Preface:If you are running oversized tires, high hp, or subjecting your truck to extreme shocks on the front, like drag racing or sled pulling, your front wheel bearings will not last much past the 36k mi warranty.

Do you need to replace wheel bearings on a Chevy Silverado?

Replacing the wheel bearings is a bit of a tedious process, but definitely important for the well being of your truck. This article applies to the Chevrolet Silverado 1500 (2007-2013). Unless you’ve replaced a wheel hub bearing yourself, chances are you’ve never actually seen one.

How big is the front wheel bearing Assy?

IMPORTANT TORQUE SPECS Hub and Bearing Assembly to Steering Knuckle Bolts – 180 N·m / 133 lb ft Axle Shaft Nut – 210 N·m / 155 lb ft Caliper Mounting Bracket to Knuckle, Front – 300 N·m / 221 lb ft Here’s the new hub/bearing assy. There is some electrical tape on the wire holding them together, tear it off.

Does the torque spec vary for the front wheel bearing assembly?

Does the torque spec vary for the front wheel bearing assembly depending depending on the year? Are you looking for the spec for an 08 hub assembly? If so, yes they are the same spec. The nnbs should be the same for half tons.

Why is my front wheel bearing making a noise?

Gotta do a long haul on Monday so I’m going to replace one of my front hub assemblies that has started making a bit of noise. I can’t believe how often these damn hubs wear out.

Are you looking for the spec for an 08 hub assembly?

Are you looking for the spec for an 08 hub assembly? If so, yes they are the same spec. The nnbs should be the same for half tons. Get a factory service manual or a after market book for your truck, it should have all or most of the torque numbers you’ll need.

How do you remove a wheel on a Chevy Silverado?

Remove the wheels after jacking up the truck. In order to remove the spindle where the bearing is housed, you must first remove the brake assembly. Start by using the 19mm socket and ratchet wrench to remove the two bolts that hold that caliper in place. Then use the 18mm socket to remove the caliper bracket.

How do you remove a brake bearing on a Chevy Silverado?

In order to remove the spindle where the bearing is housed, you must first remove the brake assembly. Start by using the 19mm socket and ratchet wrench to remove the two bolts that hold that caliper in place. Then use the 18mm socket to remove the caliper bracket.

Is the rear wheel seal leaking on a 2002 Silverado?

2002 Silverado 2500HD had a rear wheel seal leaking. This is what is involved with replacing the seal. Should be the same for most trucks with the floating axle. This video contains affiliate links, which means that if you click on one of the product links and buy, I’ll receive a small commission. Loading…

How do you replace the front wheel on a Chevy Silverado?

Once the lubricant wears out due to mileage or abuse, they can start grinding and vibrating. Start by using the lug nut wrench to partially loosen the lug nuts, then find the appropriate jacking spot for your truck, and jack it up using the floor jack.

When to replace the spindle on a Chevy Silverado?

But even parts designed for this kind of job eventually wear out. Keep in mind that in the Silverado, the bearing is sealed in the spindle assembly, and the whole part may be replaced. Once the lubricant wears out due to mileage or abuse, they can start grinding and vibrating.

How big is the hub nut on a Chevy Tahoe?

Discussion in ‘ Engine & Drivetrain ‘ started by Mr T, Jan 19, 2019 . Doing a left front Hub replacement. Want to make sure I have the right size long socket for the hub nut for the cv joint.

What’s the size of a hub bearing nut?

From buying research to owner support, join 1.5 MILLION GM Truck Enthusiasts every month who use GM-Trucks.com as a daily part of their ownership experience. What Size Socket For Hub Bearing Nut? No registered users viewing this page. What’s your preference, AT4 or Denali? 1995 GMC C1500 rear end noise.

Discussion in ‘ Engine & Drivetrain ‘ started by Mr T, Jan 19, 2019 . Doing a left front Hub replacement. Want to make sure I have the right size long socket for the hub nut for the cv joint.

How big is the nut for the CV joint?

Want to make sure I have the right size long socket for the hub nut for the cv joint. I drive an ‘08 Yukon Denali; I’m sure all are the same, but just in case. I’ve ordered ACDelco replacement HUB and knockoff axle since I’ve heard the hub should be OEM—if possible—but the axle isn’t as critical in terms of OEM quality.

How big is the CV axle nut on a Yukon Denali?

I drive an ‘08 Yukon Denali; I’m sure all are the same, but just in case. I’ve ordered ACDelco replacement HUB and knockoff axle since I’ve heard the hub should be OEM—if possible—but the axle isn’t as critical in terms of OEM quality. Thanks! I believe it’s 35mm. I’d have to check out in the garage to make sure, but it’s either 35mm or 36mm

How to remove and install a truck hub bearing assembly?

Watch the experts at Timken remove and install a truck hub bearing assembly on a GM 4×4 front wheel with outboard mounted rotors. The experts will show you how to remove a hub assembly and then show you how to install a hub assembly.

Hammer the back of the assembly. Remove the 33mm nut again and then pull the hub assembly off. Remove the triangle shaped backing plate from the back of the assembly; you’ll be reusing this. Install the backing plate onto the new hub assembly; it just slides on.

How do you jack up a Chevy Silverado?

Using the tire iron, loosen the lug nuts on the wheel. Raise the vehicle using the floor jack high enough to get the wheel off. Position the jack stand under the lower control arm. Finish removing the lug nuts and then remove the wheel. Lower the truck onto the jack stand. (Related Article: How to Jack Up Your Truck – ChevroletForum.com) Figure 1.