What does b1342 mean on a Ford ECU?

The B1342 code means that the Electronic Control Unit (ECU) has failed, usually the code is combine with other issues or codes. Repair other problems before replacing the ECU What does this mean? Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors.

What does b1342 faulty control module code mean?

The B1342 is a fairly straight forward code pointing to a fault with the Electronic Brake Control Module (aka “ABS Module”). When this code sets alone, more times than not, the module has failed internally and will need to be replaced. Inspect the electrical connector and wire harness for any loose, broken or damaged wires before replacement.

What does b1342 stand for on a car?

The B1342 is a fairly straight forward code pointing to a fault with the Electronic Brake Control Module (aka “ABS Module”).

What does ABS code b1342 on Ford Explorer mean?

Hi, I got Ford Explorer XLS 2006, VIN: 1FMEU72E06UB24150, the computer showed up two errors C1285 Booster Solenoid Circuit Failure and B1342 ECU is failed. What does it mean and which parts are defect … read more I have a 2001 taurus with a/t, a/c, 3.0 dual overhead cams with abs code B1342. Do I need to replace the control modual?

What does it mean when your ECU says b1342?

B1342 – ECU Is Defective. B1342 Possible Causes. The B1342 code means that the Electronic Control Unit (ECU) has failed, usually the code is combine with other issues or codes.

What does the b1342 code on a Ford mean?

The B1342 code means that the Electronic Control Unit (ECU) has failed, usually the code is combine with other issues or codes. Repair other problems before replacing the ECU How is the B1342 FORD code repair?

How much does it cost to repair a b1342 ECU?

The cost of diagnosing the B1342 code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

How much does it cost to diagnose b1342 in a car?

The cost to diagnose the B1342 code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars?

Note that in the case of Ford products, this code can refer to almost any controller that is not concerned with engine/fuel/transmission management functions. After proper recollection of that code, I remembered, it was a body code B1342. Which equals a antilock brake module failure.

What does b1342 stand for on a scanner?

B1342 – Ford: “ECU IS FAULTED”, or on some scanners, “ECU Failure”. Note that in the case of Ford products, this code can refer to almost any controller that is not concerned with engine/fuel/transmission management functions. B1342 – GM: “Device power #4 (high current #2) circuit low”.

What does b1342 stand for on a Jaguar?

B1342 – Jaguar: “Internal ABS control module failure” B1342 – Ford: “ECU IS FAULTED”, or on some scanners, “ECU Failure”. Note that in the case of Ford products, this code can refer to almost any controller that is not concerned with engine/fuel/transmission management functions.

What does the OBD 2 fault code b1342 mean?

END OF SPECIAL NOTES. OBD II fault code B1342 is most commonly defined as “ECU (Electronic Control Unit) has failed”, or sometimes as “GEM (Generic Control Module) has failed”.

What does it mean to have fault code b1342?

Always consult the manual for the application being worked on for accurate and relevant information on code B1342 as it applies to that particular application. END OF SPECIAL NOTES. OBD II fault code B1342 is most commonly defined as “ECU (Electronic Control Unit) has failed”, or sometimes as “GEM (Generic Control Module) has failed”.

Is there a problem with my 2010 Fusion?

On 2010 Fusion’s built before August 2009, there is a problem with the starting process. On occasion, the starter will turn the engine, but the engine will not start. The starter will not time out and the only way to stop the starter is to turn the key to the “off” position.

Where does the b1342 fault code come from?

B1342 means there is a configuration error in the module you are scanning – in this case, since you selected ABS, the code is stored in your ABS module. This is important because the same code number means the same thing if it were stored in the PCM, instrument cluster, even the radio.

What does b1342 mean on an ABS module?

Using my Autel ML629 Scan Tool and checking the ABS module I get a B1342 Fault code saying possible issue with RAM/ROM in ECM.. I assume since I’m scanning the ABS module it means the fault is really with the ABS module not the Engine Control Module? I did look up through Autel to make sure this tool did ABS diag’ on Ford before having a go at it.

What does b1342 stand for on a controller?

NOTE #2: In some cases, code B1342 does not specifically refer to any particular controller. Instead, the code definition as displayed on the scanner might refer to a system such as the ABS, air bags, or electronic power steering.

What’s the trouble code for a Ford engine?

Trouble Code. Fault Location. Probable Cause. P0171. Fuel trim (FT) system too lean, bank 1. Intake/exhaust leak, AIR system, MAFNAF sensor, fuel pressure/pump, injector (s), HO2S. P0300. Random Cylinder Misfire (Cylinder Not Specified) Spark plug (s), HT lead (s), injector (s), ignition coil (s), low compression, wiring.

What causes an intermittent code on a Ford u1900?

U1900 FORD Tech Notes. This is typically a false/intermittent code. It can occur if: Someone hooks up a scanner to the OBDII port while the ignition is on or while the engine is idling. A trailer brake system is installed improperly/incorrectly on a truck with ABS (anti-lock brakes).

What does the p0316 Ford engine code mean?

The Crankshaft Position (CKP) sensor signal is monitored by the Engine Control Module (ECM) for errors. The P0316 code is set when ECMis detects a misfire during the first 1,000 revolution test interval following engine start. P0316 FORD More Information Need more information on how to fix the P0316 FORD code? Get Access to Factory Service Manuals

When does the b1676 code set on a Ford?

The B1676 code is set when the Anti-Lock Brake System (ABS) module detects system voltage is less than 9 volts or grater than 19 volts for more than 8 seconds. In other words if the battery voltage is too low or the alternator is not charging properly the B1676 code will set.

How much does it cost to diagnose b1676 Ford engine light?

The cost of diagnosing the B1676 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

What causes the b1676 code to go off?

Fused battery voltage and fused ignition voltage is supplied to the Anti-lock Brake System (ABS) module from battery junction box fuses. Blown fuse or open circuit could trigger the B1676 code. Need more information on how to fix the B1676 FORD code?

What does the b1342 code in OBDII mean?

The B1342 code means that the Electronic Control Unit (ECU) has failed, usually the code is combine with other issues or codes. Repair other problems before replacing the ECU How do I fix code B1342 FORD? Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors.

What kind of drive does the Ford Edge have?

Front-wheel drive (FWD) is standard; all-wheel drive (AWD) is optional. A turbocharged 2.7-liter V6 endows the Edge ST with 335 horsepower (achieved with premium gasoline), and this model has all-wheel drive included.

What does b1342 mean on a Ford ECU?