Easy tips

Why do my brake lights not work on my GMC Sierra?

Why do my brake lights not work on my GMC Sierra?

I have a 1994 GMC Sierra C1500 2WD with 4.3l w/automatic. It was a fleet vehicle. Plain Jane accept for High Output Heater, Limited Slip Diff and Engine Block Heater. Brake lights were working intermittently. Would come on when pedal as first depressed then go out after pedal traveled down a bit. I put in a new switch and all was well for 3 months.

What to do if your brake lights are not working?

Ok, changed out turn signal switch and still have no brake lights. Again, i changed the bulbs, replaced the brake switch, and replaced the turn signal switch. The parking lights work, the blinkers work, the back-up light works, and the hazzards work. But still no brake lights.

What makes the brake lights come on on a 1998 Silverado?

It does look like a bracket, that wraps around the brake pedal arm. When the brake pedal is pressed down it pushes the cylinder switch together which closes the circuit and makes you brake lights come on. Check your fuses as well as your wiring to the brake light housing. Also make sure that you have working bulbs and the right bulbs are inserted.

Why are my tail lights not working but brake lights are working?

Burnt out light bulbs – The other reason your tail lights are not working but your headlights are maybe a blown bulb. When the filament inside the bulb breaks it cannot illuminate the gas enclosed within the glass cover. This burnt-out bulb does not affect the circuitry of the light system and it continues to function normally.

I have a 1994 GMC Sierra C1500 2WD with 4.3l w/automatic. It was a fleet vehicle. Plain Jane accept for High Output Heater, Limited Slip Diff and Engine Block Heater. Brake lights were working intermittently. Would come on when pedal as first depressed then go out after pedal traveled down a bit. I put in a new switch and all was well for 3 months.

Where are the brake lights on a Chevy Silverado?

Check the Brake Lights Circuit. Start at the fuse box under the hood and make sure the brake lights fuse is not blown, that the terminals are free of corrosion and that the connections are tight. Then check the brake light switch on the bake pedal arm. Back probe the switch terminals with a test light.

Ok, changed out turn signal switch and still have no brake lights. Again, i changed the bulbs, replaced the brake switch, and replaced the turn signal switch. The parking lights work, the blinkers work, the back-up light works, and the hazzards work. But still no brake lights.

Where do the brake lights go in a car?

The way those taillights work theres a white wire under dash on the column that white wire is for brake light. So the way the brake lights work they go through a relay and through blinker switch.

Where is the brake light switch on a 1998 Silverado?

The brake light switch is on the arm from the brake pedal to the brake booster (under the hood). It is held in place by a snap clip that is nearly impossible to get off, so don’t. Buy your switch and a new snap clip and then take a large screwdriver and shove it between the top of brake petal and the switch.

What to do when none of the brake lights work?

None of the Brake Lights Work When none of the brake lights work, you need to concentrate on those components or devices that may affect the whole circuit: This includes the fuse, brake light switch, turn light switch (on some vehicle models), and the part of the circuit feeding current to the brake light circuit.

Where are the brake lights on a C / K 1500?

There is a switch. I think on most C/K 1500/2500 it is on the brake pedal arm or the arm hits it. It is $5-$10; you might take ALL your truck data to the auto parts store, buy a new switch, then look for the same thing around the brake arm or under the hood. There’s a fuse. Find the fusebox and look for “brake”. The Owner’s Manual may have clues.

There is a switch. I think on most C/K 1500/2500 it is on the brake pedal arm or the arm hits it. It is $5-$10; you might take ALL your truck data to the auto parts store, buy a new switch, then look for the same thing around the brake arm or under the hood. There’s a fuse. Find the fusebox and look for “brake”. The Owner’s Manual may have clues.

Where are the 3rd brake lights on a Chevy 1500?

The 3rd brake light is on a seperate circuit from the brake lights . Test for power at the brake switch.Orange is 1 and white is the other,they are next to each on the switch.If that checks out try fiddling with the hazards and turnsinals since the brake light power flow goes form the brake switch to the turnsignals.

Why does the emergency brake light stay on in my Chevy C1500 pickup?

Why Does the Emergency Brake Light Stay on in My Chevy C1500 Pickup? Vincent Ciulla is a certified master automotive technician who has diagnosed and repaired light trucks, domestic and foreign cars, and diesel engines, for more than three decades.

What kind of brake light is not working?

The C/K line includes pickup trucks, medium-duty, and heavy trucks. Same issue . Driver’s side tail light brake light and turn signal not working . Passenger side is working no reverse lights that I know of . Bulbs seem good fuses seem good.

Which is the GMC light duty pickup truck?

GMC light duty pickup trucks deliver exceptional power and efficiency without sacrificing attention to detail. The GMC Sierra 1500 light duty pickup delivers intelligent power and performance, while the Sierra Denali pickup truck feature standard signature appointments and premium accents.

What is the brake light pattern on my 1992 Chevy C / K 1500?

I have a 1992 Chevrolet C/K 1500. My brake light on my dash has been on ever since I got it, and today the light started blinking in a pattern. I’ve looked everywhere, but I can’t find anything about it. The pattern is 3 short blinks and 1 long blink. Any Ideas?

Why Does the Emergency Brake Light Stay on in My Chevy C1500 Pickup? Vincent Ciulla is a certified master automotive technician who has diagnosed and repaired light trucks, domestic and foreign cars, and diesel engines, for more than three decades.

What causes the brake warning light to come on?

It can also be the result in worn disc brake pads. If you see the Brake Warning Light illuminated, it is probably a leak. Although, if you have a fluid level sensor in the master cylinder reservoir, you may see this light come on when the fluids are low. Brake failure is common if the fluid leaks out of the system.

Can a DTC 9 be set while the brake lamp is off?

DTCs 6, 9, and 10 will only turn the BRAKE lamp on while the fault exists. These are soft codes faults and can only be read with the Tech 1 scan tool. Do not jump terminal A to terminal H if the BRAKE dashboard lamp is not on. Jumping the terminals while the BRAKE lamp is off will set a false DTC 9.

The way those taillights work theres a white wire under dash on the column that white wire is for brake light. So the way the brake lights work they go through a relay and through blinker switch.

It does look like a bracket, that wraps around the brake pedal arm. When the brake pedal is pressed down it pushes the cylinder switch together which closes the circuit and makes you brake lights come on. Check your fuses as well as your wiring to the brake light housing. Also make sure that you have working bulbs and the right bulbs are inserted.

Why does my brake light work when I Turn on the turn signal?

For that to work, the brake wire runs to the turn indicator, so that when you turn on the flashing turn signal, it switches out the brake light signal for that side so that the two signals don’t collide. So don’t just check the brake light. Also check the turn signals.

The 3rd brake light is on a seperate circuit from the brake lights . Test for power at the brake switch.Orange is 1 and white is the other,they are next to each on the switch.If that checks out try fiddling with the hazards and turnsinals since the brake light power flow goes form the brake switch to the turnsignals.

Where is the brake light switch on my car?

Fuse Box and Light Switch. You have to find the fuse box or the power distribution center (PDC). You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm.

How do you replace the brakes on a 1998 GMC Sierra?

Replacing the brakes on the 1998 GMC Sierra is a relatively easy task. Open the Sierra’s hood and remove approximately half of the fluid from the brake master cylinder using a turkey baster. Place this fluid in a clean container for reuse. Loosen the front lug nuts with a ratchet and socket, but don’t remove them yet.

Why does my GM ABS brake still run?

The antilock brake system (ABS) is controlled by its own computer. When it senses a problem, the ABS module on the dashboard will light up. When the problem is fixed, the module will sometimes still stay on, and it will need to be rest.

How can I reset the GM ABS brake module?

Navigate to the “ABS” menu on the computerized scan tool by pushing the down arrow button. Select “Clear all codes.” Power off the computerized scan tool and disconnect it from the DLC connector. Turn on the vehicle and verify that the ABS module is no longer lit. A computerized scan tool can be purchased online, or at any automotive supply store.

What kind of brake lights are not working?

I have a 1994 Chevy 1500. Brake lights are not working. I… i have a 1994 Chevy… i have a 1994 Chevy 1500. Brake lights are not working. I replaced the bulbs and the brake light switch.

Where are the brake lights on a Chevy C / K 1500?

There is a break light relay I think down under drivers side, or under the hood in the fuse box. Blinkers are working so the circuit is good. 32 people found this helpful. Thanks Rowefast, it was the brake light relay.

Where are the brake lights and tail lights?

In most European cars, the same bulb does the job of the tail and brake lighting. However, it has double filaments, allowing one set still working while the other set is burnt. You have to find the fuse box or the power distribution center (PDC). You will get the fuse panel under the dashboard and the PDC under the hood.

Why are the brake lights not working but the tail lights are?

Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). Push the bulbs and turn them counterclockwise to remove from the socket.

When do the brake lights turn on in a car?

The brake lights turn on when you apply pressure on the brakes. In most automobiles, the taillights are red while the brake lights are a brighter, more luminous red. The rear lights are controlled by the same switch as the headlights. The power flows through a relay to the rear lights when the switch is turned on.

Where is the fuse on the brake light?

You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm. Any problem with the fuse box and light switch will affect the brake lights. In case if the fuse is blown, change it with a new one.

How long does it take to replace a brake light bulb?

How long does it take to fix a brake light? 1 hour. This is the maximum time for brake light bulb replacement since it is not complicated at all. The process should be around 40 to 60 minutes to complete.

What to do when your brake lights are not working?

In the situation when brake lights are not working properly, you need to make sure that the power is going through and check the fuse. If the brakes lights are turned on at the same time as turn signal lights, you need to bring it to the mechanics for a check.

The brake lights turn on when you apply pressure on the brakes. In most automobiles, the taillights are red while the brake lights are a brighter, more luminous red. The rear lights are controlled by the same switch as the headlights. The power flows through a relay to the rear lights when the switch is turned on.

Why are the brake lights on my GMC Sierra not working?

GMC Sierra Questions – Why won’t my turn signal and brake lights on the rear of the truck wor… – CarGurus rear turn signals and brake lights don’t work. no power in yellow wire all the way to the firewall. everything under dash works right, looks right, indicator lights work and front lights work fine.

Why are the brake lights on my car not working?

Both rear Running lights work. The green wire with red strip on left side gets no power all the way up to the front speaker kick panel. BUT, when I check for power at the brake light light switch, power is on one side of switch, then I press pedal down, power on other side.

What to do when your brake light comes on?

Only one of the switch terminals should turn on the test light. When you depress the brake pedal, both switch terminals should turn on the test light. If only one of the wires turns on the test light, unplug the switch and jump the two connections at the connector. If the brake lights come on, replace the switch.

What to do when your brake lights won’t turn off?

Have an assistant stand behind the vehicle. Check if the stopper is on the pedal. Press the brake pedal to gain access to the switch, and press button on the brake light switch. If this does not turn the brake lights off or the button fails to depress all the way, the switch might need to be replaced.

Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). Push the bulbs and turn them counterclockwise to remove from the socket.

Locate the switch near the top of the brake pedal underneath the dash. Have an assistant stand behind the vehicle. Check if the stopper is on the pedal. Press the brake pedal to gain access to the switch, and press button on the brake light switch.

Have an assistant stand behind the vehicle. Check if the stopper is on the pedal. Press the brake pedal to gain access to the switch, and press button on the brake light switch. If this does not turn the brake lights off or the button fails to depress all the way, the switch might need to be replaced.

Locate the switch near the top of the brake pedal underneath the dash. Have an assistant stand behind the vehicle. Check if the stopper is on the pedal. Press the brake pedal to gain access to the switch, and press button on the brake light switch.

How can I tell if my brake lights are blown?

Usually, you can tell if the fuse is blown by looking at the fuse element through the clear plastic box. However, if you need to confirm that the fuse is still good, you can check it using a digital multimeter. Set your multimeter to Continuity, or to a low setting in the Ohms scale. Touch each fuse connector with a multimeter lead.

What happens when your brake lights are not working?

While the brake light switch is connected to the brake pedal which comes on when the pedal is pressed. When the tail lights fail or do not function properly the car becomes a danger or hazard to self and others on the road. You may receive a ticket or citation from the traffic police. The Causes Why Tail Lights Not Working

What do you need to know about brake light switches?

When checking the brake light switch (or any type of car electrical circuit for that matter), it’s a good idea to have on hand the repair manual for the particular vehicle model. The manual comes with the location of the brake switch, the brake light circuit diagram, and lets you identify wires and connections.

Can you drive a GMC Yukon without brake lights?

Driving around without brake lights is a traffic violation. A car can not pass safety inspection without brake lights so the owner is forced to pay the money for the replacement part from which GMC profits. . Why is this not a safety recall? GMC knows it is a manufacturing defect that can possibly cause a serious accident as a result.

Where is the brake light switch on a car?

When the brake pedal is pressed, it closes the switch, and the current flows through the wiring to the brake lights. This turns on the rear brake lights. The brake light switch can also be located on the master cylinder. Hydraulic pressure from the master cylinder brake light switch system can close the switch to turn on the brake lights.

Why is the warning light on my Chevy c2500 not working?

The most obvious culprit is the switch located immediately under the parking brake pedal. If this malfunctions, the warning light may glow even if the brake has been released. Check this first and rule it out as a possible cause. This is a known issue on Chevy C1500 pickup trucks equipped with rear-wheel anti-lock (RWAL) brake systems.

Why is the brake warning light still on?

And when the obvious problems have been considered and ruled out, sometimes the dashboard warning light still remains illuminated. Naturally, the first step is to consider the obvious reasons why that dashboard warning light keeps glowing. The most obvious culprit is the switch located immediately under the parking brake pedal.

Why does the parking brake light stay on on a GMC Truck?

If You Have Air Ride On Your Truck I Know If You Dont Have Bumpstops In That The Bed Or Something Back There Will Smash The Line That Runs Over The Top Of The Axle… I Had To Relocate Mine Cause I Was Hauling My Motorcycle And Hit A Bump And Cracked The Line.

The most obvious culprit is the switch located immediately under the parking brake pedal. If this malfunctions, the warning light may glow even if the brake has been released. Check this first and rule it out as a possible cause. This is a known issue on Chevy C1500 pickup trucks equipped with rear-wheel anti-lock (RWAL) brake systems.

Why does the brake warning light keep glowing?

Naturally, the first step is to consider the obvious reasons why that dashboard warning light keeps glowing. The most obvious culprit is the switch located immediately under the parking brake pedal. If this malfunctions, the warning light may glow even if the brake has been released.

What should I do if my brake lights dont work?

Solder and shrink tube the new wire to these pigtails and give it a test. If you are unsure of the wire color associated with brake light function, you can access wiring diagrams online, but be warned, chev/gm have been known to change color codes from time to time.

For that to work, the brake wire runs to the turn indicator, so that when you turn on the flashing turn signal, it switches out the brake light signal for that side so that the two signals don’t collide. So don’t just check the brake light. Also check the turn signals.

Solder and shrink tube the new wire to these pigtails and give it a test. If you are unsure of the wire color associated with brake light function, you can access wiring diagrams online, but be warned, chev/gm have been known to change color codes from time to time.

What are the fuses for the brake lights on a Silverado?

The current path from what I can guess starts at the battery, through a 25 amp stop lamp fuse, connector c202, 15 amp vehicle stop fuse, connectors e7 and c3, rear lamps junction block, then to the stop lamps themselves. Edit; there’s also a separate 10 amp fuse for the high center stop lamp it appears, named “vhl chmsl” fuse for some reason.

What causes brake lights to not work but tail lights do?

5 Causes of Brake Lights Don’t Work But Tail Lights Do 1 Bad Light Bulbs 2 Bad Brake Light Switch 3 Broken fuse or fuse box 4 Bad sockets and connectors 5 Broken wire More …

Where are the brake lights on my 2001 Silverado?

When this happened on my 2001 Silverado, there was a corroded connection in the junction box under the rear of the truck, behind the spare tire. Your model year is not that far off from mine, so there may still be this junction box.

Where is the fuse block on a GMC Sierra?

The center instrument panel utility block is located underneath the instrument panel, to the left of the steering column. The underhood fuse block in the engine compartment on the driver’s side of the vehicle near the battery. Lift the cover for access to the fuse/relay block.

What’s the brake light on a GMC Sierra?

Since I got it back however the abs light was coming on and off and the left front brakes would bddddtttt grab and make an awful ffflllllpppp sound and scare me to death. Took it to Auto Zone and the girl put the code diagnostic on it and showed me it was the left front brake with a code of 225 and 227, the speed sensor.

Why does my abs light come on on my GMC Sierra?

Im having a problem on my 2004 sierra where my abs light comes on when i hit bumps in the road. but then it will go away either on its own or when i turn the truck off and back on. this all started happening after i got my tires aligned. ive already replaced the front two wheel bearings this year as well 293 people found this helpful.

Where is the ABS sensor on a GMC Sierra 1500?

64 people found this helpful. In many cars and trucks, the abs sensor is built into the wheel bearings of each wheel. These thin wires can become corroded and break, especially if you live in the Northern states where road salt is a plenty in the winter. As the previous reply stated- check the fluid first.

Why does my third brake light not work?

Jim, common problem. If your third brake light works either way but the rear brake lights stop working when the truck is on its a faulty ground wire to the stop lamp relay. Other things use that ground when the key is on so its not strong enough then to activate the armature within the relay.

Where is the brake light switch on a GMC Truck?

Brake Light Switch: How Do I Change My Brake Light Switch on My How do I change my brake light switch on my 1996 GMC 1500 series truck? have the same problem? The switch is located at the top of your brake pedal. You pretty much just have to unclip the old one and put the new one on.

Why are my brake lights not working on my 1998 Silverado?

When the brake pedal is pressed down it pushes the cylinder switch together which closes the circuit and makes you brake lights come on. Check your fuses as well as your wiring to the brake light housing. Also make sure that you have working bulbs and the right bulbs are inserted.

I have a 1994 Chevy 1500. Brake lights are not working. I… i have a 1994 Chevy… i have a 1994 Chevy 1500. Brake lights are not working. I replaced the bulbs and the brake light switch.

How do you turn on the brake light on a Chevy Silverado?

Back probe the switch terminals with a test light. Only one of the switch terminals should turn on the test light. When you depress the brake pedal, both switch terminals should turn on the test light. If only one of the wires turns on the test light, unplug the switch and jump the two connections at the connector.

What should I do if my brake light wont turn on?

Only one of the switch terminals should turn on the test light. When you depress the brake pedal, both switch terminals should turn on the test light. If only one of the wires turns on the test light, unplug the switch and jump the two connections at the connector.

What kind of brake lights do GM cars have?

Description: Silverado, sierra. Power Adjustable Pedals. Without active brake control. Description: XT5. XT6. Acadia. Enclave. Traverse. Blazer. 3.6l. Blazer. 2.5l. Without e-boost. Brake pedal position sensor. Description: Verano. Description: Auto trans. Canyon, Colorado. Brake pedal position sensor.

Author Image
Ruth Doyle