What causes a Chevy S10 engine to idle rough?

If an oxygen sensor goes bad, it can make your S10 run too lean (or rich). A super lean running engine will often idle rough. The fuel injection systems job is to atomize the fuel into fine mist.

What’s the diagnostic code for a s 10 engine?

F for at least 4 seconds after the engine had been running for 2 seconds. 16 – System voltage high – Charging system voltage was either below 9 volts or above 17 volts for 10 seconds.

What are the O2 sensors on a Chevy S10?

The oxygen sensors that are equipped in your Chevy S10 are responsible for monitoring the exhaust to help the ECU determine the correct air/fuel mixture. Of all the sensors equipped in your vehicle, the O2 sensors may have it the hardest. They deal with super hot exhaust that can cover them in deposits that can leave them ineffective.

Can a bad oxygen sensor cause rough engine idle?

Rough Engine Idle. Vehicle engines that have a bad oxygen sensor often run irregularly or roughly. Oxygen sensors can control or contribute to many different engine functions, including fuel/air mixture, engine timing and engine combustion intervals. A faulty oxygen sensor can disrupt any of these things and cause a rough engine idle.

If an oxygen sensor goes bad, it can make your S10 run too lean (or rich). A super lean running engine will often idle rough. The fuel injection systems job is to atomize the fuel into fine mist.

Why does my car’s exhaust smell like gas?

The fuel injectors or carburetor on your vehicle regulates fuel flow into the combustion chamber. If an injector or carburetor begins leaking fuel into the combustion chamber, it creates a rich running condition. This results in a rough idle and unburned gas making it into the exhaust, creating a gasoline smell in the exhaust.

Why does my Chevy Cobalt have rough idle?

An internal combustion engine needs air, fuel, and spark in order to achieve ignition. When one or more of these variables is off it can lead to a rough idling condition. Most of the time the culprit is going to be the ignition system, although there are a myriad of other causes.

Why are the spark plugs on my Chevy S10 not working?

Spark Plugs – One of the absolute most common causes (if not the most common reason that your S10 may be misfiring) is the spark plugs. Although most modern vehicles use iridium spark plugs, they still need to be changed at the manufacturers recommended interval. This page has a great chart for you to compare your spark plug condition to new plugs.

What does it mean when your car is idling but not running?

When the engine is running but the vehicle is not moving, this means the engine is idling. During this time, the number of revolutions per minute (RPM) inside the engine will change.

What are the symptoms of engine running rich?

7 Symptoms of an Engine Running Rich 1 Check engine light. When the fuel to air ratio is high, you will have the check engine light coming on. 2 Fuel smell from exhaust. 3 Constantly refilling your gas tank. 4 Poor engine performance. 5 Black smoke from exhaust. 6 High carbon monoxide content. 7 Sooty spark plugs. …

Why does my car run rough at idle?

That is to say combustion may be disrupted. You will feel, and maybe hear, this as a brief stutter in the engine. You might feel that the engine runs rough or vibrates at idle, say, when you’re sitting at a red light. This is similar to the above in that it stems from poor spark timing.

Can a bad throttle position sensor cause idle surging?

Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS. At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges. 3) Check Engine Light

When is a bad throttle position sensor a warning sign?

Engine won’t idle smoothly, idles too slowly, or stalls If you start to experience engine misfires, stalling, or rough idling when the car is stopped, it can also be a warning sign of a failing TPS. You don’t want to wait to get this checked out!

What does it mean when your S10 won’t start?

The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your S10 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

Why is my Chevy S10 2.2 stalling?

Few days ago my wile driving my 1995 S10 2.2 I felt a little hesitation like it was time to change the spark plugs. just stop and id not want it to start at all. I check the fuel filter and visually check the gas pump flow and there is plenty of gas moving trough that area. Also check the sparks and they are all good. What else can it be? Ah!

What to do if your Chevy S-10 ignition switch is defective?

Turn on the S-10’s headlights and attempt to start the truck. If the headlights do not dim, the ignition switch is defective. If the lights dim, the ignition switch is working properly as it sends power to the starter motor and solenoid. Proceed to the next step.

Why does my Chevy S10 stall at idle?

The truck starts up just fine but sometimes when I accelerate it acts as if it doesn’t or can’t accelerate very fast. It takes a little bit of time before it will accelerate. Typically it has issues around 50-60mph Idles fine and starts fine. Just slowly started bogging during acceleration last week.

What kind of engine does a 1988 Chevy S10 have?

I have a 1988 S-10 with a 2.8L V-6 Carb body fuel injection. The vehicle starts every time and will run from a few seconds to sometimes up to 15-20 minutes. Then it just dies like you turned the key off.

What’s the problem with my Chevy S10 engine?

Typically it has issues around 50-60mph Idles fine and starts fine. Just slowly started bogging during acceleration last week. Replaced cap,rotor,plugs,wires,coil last month,fuel filter today. With this high miles, original motor and distrubutor hmmm could be the distributor? ? Today bogging will not stop. Fastest I got on freeway was 50mph.

Why is the intake manifold weak on the S10?

The intake manifold gasket is notably weak on many S10 year models. While this not only can disrupt the air pressure and air flow of the intake manifold, which is not a welcome problem, it can also allow coolant to leak into the combustion chamber.

How do you change the idle speed on a T-30?

Insert a T-30 size Torx driver into the Idle adjustment screw that is located behind the plug removed earlier. Turn the screw to adjust the idle speed to 650 RPM +/- 50 RPM. Turn off the engine and disconnect the negative battery terminal from the battery using a wrench. Reconnect the IAC valve.

What should the idle speed be on a GM TBI?

How does the idle relearn procedure work on a Chevy?

Function An idle relearn procedure is a way to reprogram the vehicle’s computer memory to idle at a specified RPM, or revolutions per minute. Without the programmed idle, the vehicle can run arbitrarily, resulting in unnecessary engine wear. Chevy uses a simple idle relearn process.

What kind of engine was used in 1982 Chevy L69?

It was not until the 1982 model year when GM’s new corporate engine policy took effect, that the 305 then referred to as the 5.0 liter V8, became GM’s most popular V8. The 145 horsepower and 240 lb-ft of torque LG4 4-bbl 5.0 liter V8 was used in many of GM’s 1982 cars.

Where is the idle control valve on a Chevy Vortec?

The idle control valve sits on the throttle body and is responsible for adjusting the amount of air that enters the engine at idle, ultimately controlling engine idle speeds. At idle, the valve blocks a small amount of air from entering the engine, keeping idle RPM’s low.

Why is my Chevy Vortec 4300 V6 leaking fuel?

In the L35 and LF6 engines, the spider injectors are known to leak at the pressure regulator and at the supply and return lines due to a design fault. Outside of leaking fuel onto the exterior of the engine itself, it can cause excess fuel to get sucked into the engine.

What is the idle speed of a 95 Chevy S-10?

I ran compression tests and all cylinders except #5 read around 105 – 110. Number 5 reads 95 +- 5. All plugs are new with only about 5 mins on them. When I pulled them to do the compression test they all are lightly coated with black soot. RICH, RICH, RICH.

Why does my son’s 95 Chevy S-10 quit running?

My son’s has a 95 S-10. Was running great, until one day a couple of months ago, it started running really rough at a red light ( as he tells me ) and he had to work the throttle to keep it running and then about a block or two later it quit and hardly would start. When it does, it will not stay running well even with throttle work.

What to do if your car engine has rough idle?

If you own an old car and are experiencing rough idling, it is a good idea to clean the carburetor and check the hoses for damage or dirt buildup. Rough idling is a serious issue and should not be ignored for a long time. If the problem persists and is not fixed, it can lead to engine failure as well.

What does it mean when your car engine is idling?

Intake leak When you start the engine and let it run without pressing the pedal, it is called idling. When the engine is left in idling position, it maintains a steady but low rate of revolution approximately 1,000 RPM. The RPM needle stays constant, and this indicates that the vehicle’s engine is receiving the correct amount of air and fuel.

Why does my Audi A4 shake when idle?

If the vacuum system gets a leak, it will cause a shake when idle. A vacuum leak can be caused by a bad vacuum hose, intake manifold gasket, and other vacuum powered accessories. Diagnosing a vacuum leak can be tricky. Here’s a good YouTube video on how to do just that.

Why does my Chevy Captiva shake when idle?

Why does my Ford F150 shake when I idle?

Here are the main components of the ignition system, as well as what would cause them to make your F150 shake when idling. Fouled plugs can cause a misfire, which in turn causes an idle shake. Spark Plugs – One of the absolute most common causes (if not the most common reason that your F150 may be shaking) is the spark plugs.

When does a car have a rough idle?

November 27, 2017. It’s easy to tell when your car has a rough idle: When you start the engine, it won’t run at a steady rate. It may almost stall, or it may run at varying RPMs without your putting your foot on the gas, or it may do both.

Why does my vacuum have a rough idle?

Leaks in these hoses and in other parts of the vacuum system can be another cause of a rough idle, often because of a lean air-fuel mixture from excess air entering the system.

What causes a leak in the intake manifold?

These leaks can result from a variety of causes, some of which are: 1 Hose wears out, gets brittle and cracks 2 Hose connection works loose 3 Leaking intake manifold gaskets 4 Leaking vacuum supply tank More

What should the RPM be on an idling car?

When you start your engine, and just let it run without pressing on the accelerator or putting it into gear, that’s idling. A properly idling engine should be able to maintain a steady but low rate of revolutions, somewhere in the vicinity of 1,000 RPM.

Why does my Chevy S-10 not start up?

Once the truck starts and is running you can remove the jumper to the fuel pump and it will continue to run. The only thing i can think of is that you are not getting the priming signal to the fuel pump, that the ECM if faulty. It turns over fine.

Why does my fuel pump not turn on?

Well getting to start by adding fuel to the throttle body is not going to turn on some special switch that will send a signal to the pump and injectors. I’m sure you probably just have a bad fuel pump that doesn’t have enough pressure or volume to start the truck, but at running speed can keep up.

Why does my Chevy S10 engine not start?

The second way that your S10 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own. When the engine isn’t turning over at all, that’s a bit easier to diagnose than when it is cranking but not firing.

What does it mean when your car won’t start?

There are really two main ways that a vehicle will not start. The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your S10 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

What to do when your GMC Truck won’t start?

Try turning your key to the run position a few times (with out starting). Then try to start it. If it starts, sounds like what mine did. I replaced the fuel pump assembly and that fixed the problems. Very common problem.

Why is my Chevy 4.3 engine still running?

Checking your vehicle’s fluid levels is always a good idea to maintain the overall longevity of the engine. Once you have ruled out all the basics, you can go back to what the Chevy 4.3 engine is known for: bad idle air control valves and throttle control switches.

What kind of noise does a Chevy 4.3 make?

by Contributor. A common complaint with the Chevy 4.3 engine is that it doesn’t idle well, it’s loud and makes awkward noises. Examples of this are staling, lurching and poor acceleration. Poor idling and loud engines usually go hand-in-hand.

Is the engine idles fine but no power on acceleration?

This is for a 1995 chevy s10, 2.2L four cyclinder, automatic and regular body style with approximately 170 K miles. After every long trip I have to top off the engine oil. Now, I smell burnt oil and it loses power when driving and also idles rough. Also, on your conclusion, what would be a estimate ( by average ) for repairs. helpful?

Why does my Chevy S10 keep stalling?

One of the most common issues your Chevy S10 is likely to develop is a stalling problem. The most challenging part of diagnosing a stalling problem is reproducing the conditions that led to the stall in the first place. Stalls can happen at any time, and it can be incredibly jarring when it does happen.

Why does my Chevy Aveo stall when I push the gas?

Here are some of the more common causes of an engine timing problem: VVT Problem – Many modern engines are equipped with Variable Valve Timing. This allows for the engine to be in the “sweet spot” of power or economy depending on how hard you are pushing the gas pedal.

Why is my Chevy S10 engine stalling out?

This can be caused by the fuel pump or fuel filter. If your Chevy S10’s engine timing is off, it’s going to stall out, misfire, and altogether not run properly. Here are some of the more common causes of an engine timing problem: VVT Problem – Many modern engines are equipped with Variable Valve Timing.

Why does my GMC S15 stall at high idle?

In looking at the fuel injection, I can see the injectors stop injecting fuel. After it dies, it is very hard to restart unless it is left alone and cools a bit. If the IAC is unplugged, the engine will run at high idle fine. When plugged back in, the correct idle resumes and it may run a few seconds or a minute before it dies.

What’s the problem with my 1997 Chevy S10?

Any ideas on what is wrong? My Chevy 1997 S10, 38,000 miles just died. My mechanic said that he charged the battery and put in a new alternator and got it to run just to move it into his garage then it dies again. It is so dead, that none of the lights work, nothing.

What kind of problems does a 1999 S-10 have?

My 1999 S-10 has some hesitation issues and my mechanic said I needed a new fuel pump. He put one on and since then the truck starts instantly when it’s cold but when it is warm and has set for a while it will crank for a while before it starts.

Why is my Chevy S10 not taking off?

When it asks for a lot of fuel, instead of taking off, it stalls out with the demand. This can be caused by the fuel pump or fuel filter. If your Chevy S10’s engine timing is off, it’s going to stall out, misfire, and altogether not run properly. Here are some of the more common causes of an engine timing problem:

How to troubleshoot a Chevy 4.3 engine?

1 Common Problems. A common complaint with the Chevy 4.3 engine is that it doesn’t idle well, it’s loud and makes awkward noises. 2 Idle Air Control Valve and Throttle Conrtol Switch. Open up the hood and look at all the wires, spark plugs, tubes, vacuum lines and valves. 3 Check Your Oil. 4 Vehicle Fuilds. …

What are the symptoms of a Chevy Vortec engine problem?

Symptoms of Failing Idle Control Valve and Throttle Position Sensor 1 Rough idling 2 Engine stalling 3 Hesitation during acceleration 4 Hard shifting and lack of power 5 Lack of accelerator responsiveness 6 P0122 engine code (TPS sensor)

What should the idle rate be on a 1997 GMC Truck?

Underdog, I don’t know the 1997 5.7, but 1000rpm sounds like a high idle, not where it should “bottom out”. A V8 should idle at 500rpm. GoNDown, did you recently disconnect your battery? After I left mine dead in the yard for a while and didn’t charge it, when I started it up it ran like you describe for a few days and then it was fine.

What’s the idle RPM on my Chevy Suburban?

My 1997 Chevy Suburban (5.7) is acting up on me. When I start it up the RPM and idle seem fine. As I let it sit for a couple of seconds the RPM’s slowly begin to drop until they finally bottom out at about 1K. As soon as I put it into Reverse/Drive etc. the RPM’s drop below that mark and it struggles to stay running.

Can a Chevy S10 stall at any time?

Stalls can happen at any time, and it can be incredibly jarring when it does happen. Before troubleshooting any automotive issue, including stalling issues with the S10, make sure that you check the vehicles trouble codes with an OBD2 scanner.

Where is the throttle position sensor on a Chevy S10?

Your Chevy S10 uses a series of complex sensors to report what is going on to the ECU. The ECU then uses this information to adjust the timing, air fuel mixture, and more. When one of them goes wrong, it can lead to stalling for sure. Throttle Position Sensor – The throttle position sensor is typically located on the gas pedal.

What kind of engine does the Chevrolet S-10 have?

The flex-fuel (gasoline/ethanol) engine had an upgrade for some versions (LT and LTZ) and offered 206 hp with a 2.5 L LCV Ecotec with direct fuel injection. Also, for the first time in Brazil, Chevrolet offered the flex-fuel S-10 with four-wheel drive.

When did the Chevrolet’s 10 go out of production?

The S-Series ended production in Brazil in 2012, being replaced by the Chevrolet Colorado, but still with the name S-10. The first compact truck from the big three automakers was the rebadged Isuzu KB sold since 1972 as the Chevrolet LUV, and Ford quickly responded with the Mazda-built Ford Courier the same year.

What’s the fuel pressure on a Chevy’s 10?

I checked the fuel pressure and it is reading 11psi down to about 7psi. The pressure moves down and back up slowly as you race the engine and basically is pretty stable most of the time around 9-10psi.

Why is my Chevrolet S10 4×4 not working?

(Diagnose and Fix) – YouTube Chevrolet S10 4×4 Not Working? (Diagnose and Fix) If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.

Why does my car idle rough all the time?

3. Dirty Fuel Injector. Sometime dirty parts can also be the root cause of a rough idling engine. Fuel injectors disperse fuel into your vehicle’s engine at a precise angle and quantity, to ensure optimal performance. That being said, dirty fuel injectors are also a major contributor to poor gas mileage.

How often does a 94 S-10 4.3 drop rpm?

After you take it out and drive it, it’ll idle fine for a couple minutes, then will drop a couple hundred rpms every 30 seconds or so for just a count, then back to normal. Any ideas? I’m pulling my hair out.

Why does my Chevy S-10 idle so bad?

Computer does show that it is in OPEN LOOP MODE and O2 Sensor shows RICH and while working the throttle and watching the code meter, the reading will move from RICH to LEAN and back to RICH again. While all of this has helped the engine somewhat, it still barely idles and it still lops really bad.

How is my 1994 S-10 4.3 running?

Starts fine, even today when it was -15, fuel pressure 52 running, holds after shut down, newer plugs/wires/cap rotor, tested MAP sensor and tests good, tested resistance changes in TPS (with sensor out) and changes were smooth along range, unplugged every sensor I could find individually looking for changes, no luck.

What causes a misfire on a 94 S-10?

Typically if the lower intake gasket leaks vacuum, it only affects one cylinder and causes a noticeable misfire all the time. On your engine, the ECM batch fires the injectors, it can not richen the mixture for individual cylinders.

Why does my car engine run rough while idling?

When your car engine runs as it should, everything should be smooth without any noise. When any number of things goes wrong, the engine can start running rough, especially while idling. By understanding the causes of a car engine that has a rough idle, you can resolve the issue easily.

How can you tell if your car engine is idle?

You can often also feel the strange vibrations inside your car while sitting in the driver seat. However, modern cars do often have great engine mounts, and you do sometimes have to open the hood to check if the engine is vibrating or even jumping on idle.

When to clean throttle body 4.3L V6 position sensor?

Clean the throttle body to fix a sticky throttle on a 4.3 in a Blazer, S10, Silverado, and express. Also GMC Jimmy, Sonoma, Sierra, Savana. This applies to 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007.

Why are the Spider injectors leaking in the L35 engine?

The spider system uses a central pump with 6 tubes connected to it that lead to each of the 4.3L vortec cylinders. In the L35 and LF6 engines, the spider injectors are known to leak at the pressure regulator and at the supply and return lines due to a design fault.

Why is the idle speed of my car so high?

Step 2 – The idle air control motor (valve) is responsible for controlling the engine idle speed, if this part fails or becomes weak the engine idle speed could become erratic, additionally, this condition may or may not trigger the MIL (check engine, service engine soon light.)

How can I keep my car at idle?

Step 3 – Engine vacuum is a sealed system and must hold a specific amount to maintain proper idle conditions, inspect the engine vacuum hoses and intake gaskets. Step 4 – The air intake boot or tube is used to deliver air to the intake system of the engine.

What causes a Cadillac Escalade engine to stall?

If the converter doesn’t unlock, then the engine will stall much like a manual vehicle does when it doesn’t have enough speed to carry a gear. It’ll often throw code P0740. If there is almost no oil left at all, the engine could be on its way to locking up.

What is the diagnostic code for engine stall?

Diagnostic trouble codes P0120, P0121, P0122, P0123, and P0124 are what will commonly appear. The engine can stall for no reason and without any warning. This happens when the TPS gives incorrect information to the ECM. The engine can stall at high speed, at low speed, or even at idle.

How can I tell if my S10 Blazer has good spark?

If you have good spark, check the fuel filter and fuel pressure at the fuel rail. Back firing could be timing,cam position or crank position sensor.Worst case scenario, timing chain or belt.

Why does my 1990 Ford F150 not start?

83 people found this helpful. Ok I have a 1990 ford f150 300 6cylinder iv replaced starter solenoid coil and still not wanting to start don’t seem to be getting fire what could be the problem any suggestion from any one here I really like this ole truck and I will do what ever it takes to get her back on the road plz help me

What are the symptoms of a bad crankshaft position sensor?

It’s one of the most serious crankshaft position sensor symptoms. The computer receives a malfunction code when the sensor is completely gone. The symptom starts with difficulty in starting and leaves the car dead one day if you don’t get it fixed. The starting problem could be the result of electrical connection or circuit problems too. 5.

Why does my Ford truck not start when its hot?

I have an 89 f 250 mine wont restart when hot. I can move the distributer and it will start again. So weird. When its hot it sounds like the battery is dead and wont turn over till I retard the timing. 83 people found this helpful.

What causes idle surges on a car ECM?

What causes a Chevy Silverado to run rough?

If an oxygen sensor goes bad, it can make your Silverado run too lean (or rich). A super lean running engine will often idle rough. Fuel Injectors. The fuel injection systems job is to atomize the fuel into fine mist.

What causes an Audi A4 to idle rough?

A super lean running engine will often idle rough. The fuel injection systems job is to atomize the fuel into fine mist. If a fuel injector has an issue with this process, it will either let too much or too little fuel into the combustion chamber relative to the amount of air.

What happens to your car when you idle?

A rough idle will result in intense vibrations forming whenever your vehicle is stopped with the engine running. Since less air will be going into the engine during its idle state, the car will react by shaking profusely.

Why does my Chevy Blazer have a rough idle?

What are common reasons my Chevrolet Blazer has a rough idle? While there are a variety of reasons your Chevrolet Blazer has a rough idle, the most common 3 are a vacuum leak, an issue with the spark plugs, or a problem with the ignition coil. See what others are asking about their Chevrolet Blazer.

What are the symptoms of a bad idle air control valve?

Below are the top 5 symptoms of a bad idle air control valve which you will easily notice. Since the idle air control valve is supposed to manage the idle speed of the engine, a bad valve will certainly throw that out of whack. It will cause the idle speed to randomly fluctuate to different speeds rather than stay at one constant speed.

What can go wrong with a Chevy S10?

The internal combustion engine is so complex that even the slightest problem can potentially disrupt the power delivery in a very serious way. While there are things that can go wrong with any car, every car also has its own “Achilles heel” for that specific engine, and the S10 is no exception.

What causes a rough idle on an air conditioner?

A clogged air filter will not allow clean air to pass through causing a rough idle. To remedy the situation, have your air filter replaced with a new one and also have the housing serviced to clean any dirt buildup. 7. Dirty Oxygen Sensor

Are there any issues with the Chevy S10?

After that it started having a number of other issues, such as power loss, really bad acceleration, stalling, and a really rough idle.

What causes a Chevy S10 to start sputtering?

Normally it idles around 950-1050 RPM, what has been happening is that it would start, idle high, around 1500, then drop to normal, and then start sputtering and RPMs would fluctuate anywhere between 750 on the high side, all the way to 0, stalling the motor.

How to troubleshoot an automotive engine high idle?

The troubleshooting procedure for high and low idle conditions are similar, which are included in the following: Step 1 – If the check engine or service engine light soon has illuminated retrieving the diagnostic trouble codes could lead you in the right direction of what the problem is, or is related too.

When to idle high on the idle cam?

There is adjustments on the idle cam on the carb and mentioned, on warm days after you already started it, it should not idle high. But on cold days it should always idle high unless you drove it already and it has not cooled back off. You said you hit the pedal and it idles fine.

When to reset high idle cam on Carb?

Your engine should idle high (1000 – 1200 rpm) until either the choke warms and shuts off the high idle cam on the carb or like stated you hit the pedal to reset the high idle cam. I am assuming your carb has an electric choke.

Can a LS engine be swapped into a C10?

Swapping LS engines into C10s isn’t a new science, and it pays to make use of some of the well-engineered kits out there because they’ll make your swap cleaner and your conversion less complicated. You can piecemeal your way into a successful swap, or you can source parts that are known to work together already.

What do you mean high idle ( what rpm )?

There is a screw on the carb linkage to adjust the high idle.If you back it off to much,it may not idle when its cold.My truck idles at about 1200 rpm at hight idle. What do you mean high idle ? (what rpm), both answer’s are correct.

What does it mean when your car Idles smooth?

Smooth idling indicates that your engine’s fuel and air are mixing just right. What is rough idling? If your vehicle’s idle is rough, possibly rising and falling, or having difficulty maintaining a steady rate of rotation, you may have a problem that needs fixing.

Why does my GM V8 engine misfire when cold?

Because, GM V8 engines are very prone to a rough idle and engine misfire when cold. The check engine light may also come on, with codes P0300, P0171 and PO174. But, as the engine warms up, the engine misfire or rough idle tends to go away; which seems confusing.

What causes rough engine idle or TDC code?

So, should the engine misfire, rough engine idle or (TDC) code; point to an air leak in the intake manifold gasket, following the below directions. A very common cause of a leaking intake manifold is the gaskets and bolts used from the factory.

Why does my 2001 S10 have a hard starting problem?

My 2001 S10 has a hard starting problem if the truck sits between 1 to 4 hours. It starts fine if left over night. Has 46,000 miles. Cranks for about ten seconds before it starts. some part of your fuel injector is leaking into the manifold. Have fuel pressure tested, have a feeling it will shoot up to the desired 60 psi then fall back now quickly.

What causes a Chevy S10 engine to idle rough?