What are the trouble codes on a truck?

NOTE – Diagnostic Trouble Codes listed in this document are Body Controller, Auxiliary Gauge Switch Pack, Secondary Instrument Cluster, Instrument Cluster, Rear HVAC Module, and Compass Module. Comm. fault from ESC/BC to PP3.

Where do I find the trouble code on my Chevy?

These are listed in numerical order for easy searching. When retrieving Chevy trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.

Where do I find the diagnostic trouble code?

The ability to display diagnostic trouble codes (DTC) is an optional feature. Codes may be displayed on either the gauge cluster or an optional vehicle information display (VID). The vehicle must be equipped with the option to display codes in both cases. Codes will not be displayed on the gauge cluster if the vehicle is equipped with the VID.

Where are the diagnostic codes stored on an Impala?

These codes are stored on the computer until you run a diagnostic test and retrieve them. Once retrieved, you can fix your Impala, but the codes will remain on the computer. To get rid of them, you’ll need to clear the codes using a special tool called an OBD (onboard diagnostic) scan tool.

What is the CDL code for a C13 engine?

J1939 Code and Description CDL Code and Description CAT C13, C15, and C18 Tier 4 Final Engine Fault Codes 654-5 4-5 Engine Injector Cylinder #04 : Current Below Normal Cylinder #4 Injector : Current Below Normal 654-6 4-6 Engine Injector Cylinder #04 : Current Above Normal Cylinder #4 Injector : Current Above Normal 655-5 5-5

What are the fault codes for International trucks?

International Trucks Fault Codes List (DTCs) for Model: 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600, BE 200, CE Bus, CXT, DuraStar, LoneStar, MXT, ProStar, RXT, TranStar, WorkStar. See also: International Trucks Service Repair Manuals PDF

What is the fault code for a Volvo truck?

Reset ABS Faults, Body Controller Faults and more. 1 Volvo Link System Faults (MID 142) Fault Code Description FMI MID 142 PID 155 Input 1-4. 2 Vehicle ECU Faults (MID 144) 3 Climate Control Faults (MID 146) 4 Light Control Module Faults (MID 216) 5 Gear Selector Module Faults (MID 223)

What is the fault code for a mid 128 engine?

Engine ECU Faults (MID 128) Fault Code Description FMI Codes MID 128 PID 26 Engine Fan Speed Percent 3,8 MID 128 PID 27 EGR Valve #1 Position Sensor 3,4,5 MID 128 PID 45 Preheater Relay Status 3,4,5 MID 128 PID 81 Particulate Filter 0,2,3,5,12

How to know if a DTC is not available?

Suspect parameter number (SPN), failure mode indicator (FMI) and occurrence count numbers are listed. Source addresses and DTC descriptions are presented in plain text. NOTE – The VID will display “Not Available” if a DTC description is not available for a particular fault.

How to check the DTC code on a truck?

Turn the key switch to the ACCESSORY position to view only previously active codes. Turn the key switch to the IGNITION position to view both active and previously active codes. Momentarily press the Cruise “ON” switch and the Cruise “Resume” switch at the same time. A gauge sweep will be performed on the gauges.

What does DTC 99 mean on a Ford?

The lamp stays on when OSC is toggled to prevent vehicle from shifting into overdrive position. DTC 99 indicates a fault in the E4OD transmission Electronic Pressure Control (EPC) circuit. Under this condition, the lamp serves as the Transmission Malfunction Indicator Lamp (TMIL).

What are the trouble codes on a truck?