How to install a front wheel bearing and hub assembly?

Place the new wheel hub on to the spindle , Take the new hub nut and start it by hand. Take the 36mm socket and torque wrench and tighten the new hub nut to the torque of 221 to 295ft-lbs 9. Take new dust cover and center it on the hub. 10.

How much torque does a hub bearing have?

Hub Bearing Torque Specification Guide 2010 Make year Model Front torque ft-lbs/Nm Rear torque ft-lbs/Nm

What happens if your spindle nut is over torque?

It will also leave your spindle nut under or over torque resulting in hub assembly failure. Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer. It is important that you properly torque the spindle nut to ensure optimum bearing life.

How to remove hub nut from front wheel?

Take flat head screwdriver and easily tap it in around the dust cover with the hammer to remove it from the hub (the dust cover is a onetime use item, so you will have to replace it with a new dust cover each time) 6. Using the 36mm socket remove the hub nut (this is a onetime use hub nut) Remove wheel hub 7.

Hub Bearing Torque Specification Guide 2010 Make year Model Front torque ft-lbs/Nm Rear torque ft-lbs/Nm

What happens when an axle nut is over torque?

Under torque of an axle nut will allow excessive movement causing uneven loading and excessive wear. Over torque of the axle nut will cause excessive load and cause the bearing to overheat, this is one of the most common causes

Are there front wheel bearings on a Pontiac Grand Am?

The front wheel bearings on the 2000 Pontiac Grand Am are complete sealed wheel bearing and hub assemblies. They do not require servicing and repacking with bearing grease like the older rear-wheel drive cars.

How do you unlock the front wheel on a Grand Am?

Loosen the lug nuts on the front wheel with the faulty bearing using a tire iron. Do not turn the wheel nuts more than a half a turn. Lift the front end of the Grand Am with a service jack and place a jack stand under each front frame rail. Turn the ignition key a half click to unlock the steering wheel.

How do you remove a front wheel bearing?

Your objective is to remove the knuckle assembly from the vehicle so you can place it on the press and remove the wheel bearing. This is how the knuckle assembly will look once you removed it from the vehicle. Step 1.

What kind of bearings are in a wheel?

A wheel bearing is a crucial part of the wheel assembly that connects the wheel and the axle. It is a set of steel balls (ball bearings) or tapers (tapered bearings), held together by a metal ring. It enables the wheel to rotate smoothly with a minimum of friction.

What makes a front wheel bearing go bad?

If a bolt-on hub/bearing, the only thing that makes new bearings go bad is the axle nut not being torqued on tight enough. Also, you may have one bad tire (a tire that is out of round) or a bent wheel. Easiest way to find out is to move the front tires to the rear …

How to install a front wheel assembly on a car?

Jack front of the car up. Use the Lug nut wrench remove the lug nuts on the wheel and remove the wheel and place to the side. 2. Use 15mm socket to remove the brake caliper (2 bolts on back of caliper) 3. Place brakes caliper either on a cinderblock or hang it the proper height so not to damage the brake line). 4.

Where are the wheel bearings on a car?

This is because the front rotors are often behind the front hubs, which means that to change the rotors you have to pull the hubs off the front spindles, at which point the bearings are practically in your hand. So, if you need to do a front brake job, check the wheel bearings.

How does a wheel bearing support the center race?

Support the center race of the wheel bearing from underneath so that when you are pressing the hub into the center race, it will not push out the rear center race through the back side of the knuckle assembly.

How do you replace a hub bearing?

Part 1 of 1: Replacing the hub bearing. Step 1: Loosen the nuts. Loosen the lug nuts from the wheel which the bearing is going to be replaced. Step 2: Raise and secure the vehicle. Raise the vehicle and secure it on jack stands, and then remove the wheel.

What do I need to replace my front wheel bearing?

Wheel bearing assembly
Breaker bar
Jack
Socket set
Ratchet
Screwdriver
Rubber mallet
Sandpaper

Should I replace wheel hub bearing?

As a rule, sealed wheel bearings and hubs should have no play or roughness when a wheel is spun by hand. If a wheel bearing feels loose, or has play that exceeds specifications when measured with a dial indicator placed against the hub, it is worn out and needs to be replaced without delay.

What causes a wheel hub assembly to go bad?

Good wheel hub assemblies are built like tanks. But sometimes they break or wear out, like any other part on a car. When that happens, it’s easy to wonder what went wrong. There are three common causes of bearing failure: impacts, contamination, or improper alignment.

Jack front of the car up. Use the Lug nut wrench remove the lug nuts on the wheel and remove the wheel and place to the side. 2. Use 15mm socket to remove the brake caliper (2 bolts on back of caliper) 3. Place brakes caliper either on a cinderblock or hang it the proper height so not to damage the brake line). 4.

Is it possible to remove and replace a wheel bearing?

In some cases, it’s possible to remove and replace just the bearing; however, this method is fraught with risk, so most professional mechanics avoid it when they can. This configuration is most common on older cars and 2WD trucks and vans. They are the easiest to remove and replace.

Can you replace a wheel bearing at Pep Boys?

On some cars, you can just replace the bearing and call it a day. On others, the hub assembly must be removed and replaced. The most difficult type involves removing the hub assembly and setting it in a press. If you’re not sure what type of wheel hub assembly you have, stop by or give your local Pep Boys store a call.

Do you need a shop press to replace wheel bearings?

One wrong move with the press and you run the risk of damaging the hub assembly. If you’re not sure how to do this, get help from a professional mechanic. If your car or truck has a non-serviceable wheel hub assembly with press in bearings, you will need a shop press to remove and replace the bearings.