Easy tips

How do you replace the hub on a Ford Explorer?

How do you replace the hub on a Ford Explorer?

Step 9: Pull the hub from the vehicle. The spindle should now be completely unbolted from the vehicle and ready to remove using the wheel hub puller. Install the wheel hub puller using a few lug nuts, and then tighten the puller center bolt until the hub is pulled free. Step 10: Install new hub components.

How to replace wheel hub on Ford F-150?

Install new wheel hub to steering knuckle with four 18mm bolts. Reinstall the 13mm wheel bearing center nut and bearing cap. Reinstall brake caliper bracket and brake calipers.

How to replace your wheel hub and bearings?

1 Step 1 – Remove wheel from truck. 2 Step 2 – Unbolt caliper from brake disc. 3 Step 4 – Pop off wheel bearing cap. 4 Step 6 – Unbolt hub from wheel spindle 5 Step 5 – Remove wheel hub and bearing. 6 Step 6 – Install new hardware. 7 Featured Video: How to Replace Wheel Hub and Bearings

How do you replace wheel bearings on a Ford F-150?

Use an 18mm socket to detatch the four bolts holding the hub to the wheel spindle Figure 8. Figure 9. Remove the wheel bearing and hub by plling it out. use your breaker bar for leverage if it’s stuck. Figure 10. Old wheel bearing Figure 11. New wheel bearing Figure 12. New and old wheel hub

How to replace Ford Explorer rear wheel bearing-DIY?

This video outlines replacement of the rear wheel bearing, hub, parking brake shoes, brake rotors and pads. A shop press is required to service this bearing. The example vehicle is a 2002 Ford Explorer 4X4 however this example is similar to many 2000-2010 Ford Explorer and Mercury Mountaineer vehicles. Watch this video for more information.

When to replace the hubs on a Ford 4 wheel drive?

Ford specifies 56 oz. of F1TZ-19580-A or equivalent gear oil.) If the hubs are noisy or are failing to disengage, Ford recommends replacing both locking hubs. If you hear a popping or banging noise while driving in four-wheel drive, one or both hubs may be slipping or broken.

When to replace the hubs on a Ford Bronco?

If the hubs are noisy or are failing to disengage, Ford recommends replacing both locking hubs. If you hear a popping or banging noise while driving in four-wheel drive, one or both hubs may be slipping or broken. Ford used Warn Automatic Hublocks Model M350 on Bronco II and Ranger with the Dana 28 Axle from 1983-90 (through build date 10/4/89).

Step 9: Pull the hub from the vehicle. The spindle should now be completely unbolted from the vehicle and ready to remove using the wheel hub puller. Install the wheel hub puller using a few lug nuts, and then tighten the puller center bolt until the hub is pulled free. Step 10: Install new hub components.

What kind of rear axle does Ford Explorer have?

The Ford Explorer 8.8-Inch rear axle has found homes in numerous vehicles besides the Explorer. It has been swapped in to Ford Rangers, Bronco II’s, Jeeps, Chevy S-10’s and even some cars. The 8.8-Inch axle used in the Explorer is highly desirable because it came with 31-spline axles over the typical 28-spline found in the Ranger version.

What happens when a rear hub bearing fails?

They hold the entire weight of the vehicle and are subject to the harsh conditions of the road, as well as exertion from the torque of the engine. When they fail, they will begin to make a howling noise, which will progress into a grinding, and when completely failed may seize, rendering the vehicle undriveable.

What kind of brakes does a Ford Explorer have?

The 1990-1994 Explorer 8.8-inch axle came with 10-inch drum brakes. 1995 and newer Explorers have disc brakes. People have reported that they have swapped in a newer disc brake 8.8-inch axle in place of their original drum brake axle without having to switch to a disc brake master cylinder.

Author Image
Ruth Doyle