How big is the Idi torque converter nut?
How big is the Idi torque converter nut?
6.9 & 7.3 IDI Torque Specs and Bolt Dimensions, with Images Type Max Torque Bolt/Nut Size Qty Crankshaft Harmonic Balancer Retaining B 90 ft-lbs 5/8″-11 1 Camshaft Screw 15 ft-lbs Torque Converter Nuts (C6) 3/8″-16 4 Air Cleaner Stud Adapter (loctite) 45 ft-lbs 1
What are the torque specs on a Ford truck?
6.9 & 7.3 IDI Intake & IP Gearhouse Torque Specs and Sequencing. Miscellaneous torques: (Taken from the Official Ford “1988-1993 Engine Service Manual, Supplement 7.3 Liter Diesel Engine” and the Official Ford “1988 Truck Shop Manual, Vol.
What are the torque specs for steel bolts?
Oddly-Named Torques: First off, if you don’t already know, there is a baseline torque convention called the “Standard Torque.” For a typical metal thread, there is a corresponding torque limitation. This applies for general steel bolts and nuts, but many other metals and grades of steel require a higher or lower torque spec .
What’s the torque chart for an IDI engine?
The Standard Torque Chart is: Second, ALWAYS CHASE your threads prior to any engine reassembly. Do not use a short cut like a tap-and-die set. It could damage the block. Also, for major fasteners like crank main bolts and head studs, use ARP fastener lube to ensure precise torque measurement.
What is the main purpose of an intake gasket?
The intake manifold gasket works to seal the gaps between the air intake manifold, the engine block and the various cylinder heads . Gaskets can be made of a variety of different materials including cork paper, soft metal, rubber, and asbestos.
What is the intake plenum gasket?
The Intake Plenum Gasket is fitted between the upper intake manifold and the lower intake manifold of your engine. It is usually made of rubber, paper or silicone. The intake manifold is primarily responsible for distributing the air evenly to all the cylinders.
What are torque specifications?
Torque specifications are for dry threads only. The fastener threads should be free of oil, dirt, grit, corrosion, etc. The hardware should turn freely without binding when tightened by hand. It is important NOT to lubricate hardware threads or seats. The friction at which torque is measured against should come from the hardware seats.
What is the definition of an intake gasket?
An intake manifold gasket is a flexible, fitted part of a car engine that helps prevent air from leaking out during fuel combustion and helps regulate chamber temperature. Most cars use a type of engine known as “fuel combustion,” which basically means that they get their main energy from a series of mini-explosions powered by gasoline.
What are the specs for a torque converter?
Application Spec Flywheel to Torque Converter Bolt 46 ft lb Forward Accumulator Cover to Valve Body 6-10 ft lb Heat Shield to Transmission Bolt 13 ft lb Line Pressure Plug 6-10 ft lb
How much torque does a troque engine have?
Main bearing cap bolts. Torque: 39 N·m (29lb ft) NOTE: Do not allow the crankshaft to rotate. Crank case Main Bearing side bolt Torque: 39 N·m (29lb ft) Connecting Rod Cap bolts Torque: 54 NÂ·m (40 lb ft). Install main bearing caps, oil gallery and crank case bolts in the order shown, and tighten each bolt to the specified torque.
What are torque specs for passenger side engine?
Various Passenger Side Engine Torque Specs: 10.) Miscellaneous Torques: 11.) Oil Pump Bolt Information: 12.) Oil Cooler Assembly Bolt Information: (Truck) 13.) Oil Cooler Assembly Bolt Information: (Van) 14.) Oddly-Named Torques: First off, if you don’t already know, there is a baseline torque convention called the “Standard Torque.”
How big is the intake manifold on a GM 2.8L V6?
Type: Bolt Intake Manifold To Cylinder Head 23 276 31.18 Type: Bolt 7.5 90 10.17 Type: Bolt Dim: M 6 X 1.00 18 216 Type: Bolt Dim: M 8 X 1.25 33 396 Oil Pump to Rear Main Bearing Cap Bolt Type: Bolt Head: Hexagon 23 276 Type: Bolt Head: Hexagon Pulley To Vibration Damper/Hub 25 300 Crankshaft Pulley to Vibration Damper Bolts Type: Bolt
What are the torque specifications of a Ford 5.4L V8?
Type: Bolt Engine Mount To Engine Block 45 540 61.01 Modular OHC – Engine Mount to Engine Block Bolts Type: Bolt Head: Hexagon 45 540 61.01 Modular OHC – Engine Mount Thru Bolts Type: Bolt Exhaust Manifold To Cylinder Head 18 216 24.4 Modular OHC – Exhaust Manifold NUTS Type: Exhaust Manifold To Cylinder Head 9 108 12.2
What kind of torque does a dim have?
Dim: M 8 X 1.25 33 396 Oil Pump to Rear Main Bearing Cap Bolt Type: Bolt Head: Hexagon 23 276 Type: Bolt Head: Hexagon Pulley To Vibration Damper/Hub 25 300 Crankshaft Pulley to Vibration Damper Bolts Type: Bolt Head: Hexagon 19 228 Fan/Pulley to Water Pump Bolts Type: Bolt Head: Hexagon 46 552 Type: Stud 22 264 Type: 25 300 Type: Bolt 16 192
What are the torque specifications for a torkspec?
Type: Bolt Dim: M 12 X 1.50 14.92 Type: 20.34 Type: Bolt 9.49 SOHC – Oil Pump Drive Chain Guide Rail Bolts Type: Bolt 29.83 SOHC – Bearing Caps NOTE: 2 Step: 22 FtLbs + 90deg Type: 65.08 SOHC – Crankshaft Main Bearing Cap Bolts Type: Bolt 59.66 SOHC – NOTE: 4 Steps: 30; 44; 90deg; 90deg Type: Bolt