What should I do if my Ford Ranger 4×4 is not running?

The dash and 4X4 buttons should light up. If they do not, one of the following is faulty: the dash button, the 4X4 module or the shift motor. To determine which of these three is malfunctioning, have your friend sit near the module. Press the 4X4 button and ask your friend to listen for the sound of the relays in the 4X4 module.

What makes a Ford 4.0L engine not start?

This tutorial is geared toward a Cranks but Does Not Start Condition. To successfully troubleshoot the cause of the no start condition of your Ford 4.0L equipped car or mini-van, you need to know that there are three very basic components the engine needs to start and they are: Air. Fuel.

Why does my Ford Explorer crank but not start?

Spark. So, when your Ford 4.0L Explorer (Aerostar, Ranger or Mountaineer) Cranks but Does Not Start, it’s because one of these components is missing from the mix.

How can I Shift my Ford Ranger to 4×4 high?

Determine if the 4X4 system can be shifted to 4X4 high by pressing the 4X4 button. The dash and 4X4 buttons should light up. If they do not, one of the following is faulty: the dash button, the 4X4 module or the shift motor. To determine which of these three is malfunctioning, have your friend sit near the module.

Why does my Ford Ranger crank no start?

In this video we cover some basics on finding the cause for a crank no start on a Ford Ranger. Many Ford vehicles have the same ignition and fuel design. I eventually trace the issue to a defective inertia switch, causing an electrical issue not allowing the fuel pump to run. Thanks for watching!

Why does my Ford Ranger run for a little then dies?

Next check is the fuel pressure regulator, your looking for fuel coming out the top and bleeding into the vacuum line thus flooding the engine. Another thing that happens is the distributor pickup coil can fracture, it runs good until it gets hot then it will go open and the engine stalls, and the ignition module can act the same way.

What kind of engine does Ford Ranger have?

Truck has 2.9 Liter v6, fuel injected. Turns over freely. Eventually starts after maybe 60 seconds, some jockeying the acelerator. Replaced fuel filter. 92 K miles on vehicle.

Can a Ford Ranger run with low fuel pressure?

So check the lift pump first if it is running and pumping a good stream of fuel then move onto the pressure pump, and yes your fuel pressure is low. Here is a chart. All makes and models. http://jameshalderman.com/links/book_adv_eng_perf_5/s_and_c/F uel_Pressure_Specifications.pdf

Is there a 4 wheel drive Ford Ranger FX4?

I have a 1999 Ford Ranger FX4 4WD and it has just over 96,000 miles. My 4WD doesn’t work anymore. At first, it wouldn’t work sometimes, i’d have to try a few times.

When did the Ford Ranger 4×4 come out?

by Michelle Kerns. Ford Ranger 4X4s have been popular with truck owners since they were first introduced by the Ford Motor Co. in the mid-1960s. Problems with Ford Rangers can arise with either the low or high 4X4 system or the automatic or manual hubs. If you are having problems with your 4X4, follow these steps to diagnose the trouble.

Why is my 4×4 not working on my 2000 Ranger?

2000 ranger 4×4. 4×4 will not engage. Green indicator light on switch will not illuminate. 4×4 high and low lights in dash will flash 4 or 5 times when key is first turned on but they do go off. Turn the 4×4 switch on and nothing happens, no lights, nothing.

Is there a 4 wheel drive switch on a Ford Ranger?

It’s got an electronic switch in the cabin that has 2wd, 4wd high, 4wd low. When it worked, I would switch into four wheel drive and an indication would display on the dash whether it was in 4×4 high or low. That doesn’t come on when I switch anymore and I can tell that the 4×4 hasn’t engaged.

Where are the 4×4 lights on a Ford Ranger?

No 4×4 lights at key on, No click when switch is turned = 4×4 Control module – under passenger side kick panel interior. Just fixed my 2002 xlt ranger. For the lack of one shift lever sticking through the floorboard.

Why is the transfer case on my Ford Ranger not working?

The problem is usually caused by lack of battery maintenance or defective battery terminals. To prevent premature failure of your 4X4 Transfer Case Control Module, you may want to start by keeping your battery clean and terminals free of corrosion. Watch video below on Battery Care and Maintenance Tips by EricTheCarGuy

Why does the transfer case on my 1994 Ford Ranger not work?

Have a 1994 Ford ranger 4.0 5 speed transfer case won’t engage I put a new transfer motor a new module still engaged 13 people found this helpful. My question is this: Son has a 1994 Ford Ranger and when he locks the hubs and puts in 4×4 it makes a clipping sound or grinding sound and eventually stops moving until you disengage the 4×4.

Why is my a / C not working on my Ford Ranger?

Learn if it’s a simple fix or time to seek out a trusted technician. Not your vehicle? Why Isn’t My A/C Working? What are common reasons my Ford Ranger has air conditioning problems?

How does the lock button work on a Ford Ranger?

The knob in the center of the hub has an arrow to indicate if it’s in the FREE or LOCK position. When the hub is turned to the LOCK position, it pushes a splined collar onto the end of the axle shaft, connecting the hub and axle together.

How does the 4WD system work on a Ford Ranger?

When the Ranger is in 4WD, the transfer case splits the power between the front and rear axles. The front axle uses a locking hub (1983-2000) to lock (connect) the front wheels to the axleshafts. If these hubs are not locked, the wheel will not receive power from the axle. Note: the 2001-2011 4WD Ford Ranger has a live front axle.

When did the Ford Ranger get a 4WD system?

The Ford Ranger’s 4WD system shared the same basic operation from 1983 through 1994. However, the Ranger received a larger front axle (Dana 35 TTB), and a slightly different transfer case. Additionally, the transfer case electronic shift module would be mounted in different locations.

Can a Ford Ranger shift to 4WD Low range?

Note: The shift control module receives speed input from a speed sensor on the vehicle. It does not allow the transfer case to shift into 4WD if it is moving to fast, or in to 4WD Low Range if it isn’t stopped. Additionally, the transfer case will not go in to 4WD Low Range (4LO) unless it is in 4WD first.

Is the Ford Ranger a live front axle?

Note: the 2001-2011 4WD Ford Ranger has a live front axle. What that means is that the front wheels are permanently connected to the front axle, and do not use a locking hub. Misconceptions: Some believe that when you activate the 4WD, power is sent to all (4) wheels. I can see where people get that idea….from the name.

Can a 4 wheel drive Ford Ranger work?

172 people found this helpful. Have a 4 wheel drive ford ranger the neg on battery would move and 4 wheel drive would not work I would pull the fuse out it would start working sounds crazy. Battery went bad had to put new one in it now 4 wheel drive will not work. 19 people found this helpful.

How can I test my Ford Ranger 4×4?

To test a car with manual hubs, make sure the 4X4 is off and rotate the axle until it locks up. Again, if the axle does not lock up, the hub is not working or in need of a cleaning. To determine if the automatic hub is no longer working, take the car out of 4X4 mode and rotate the axle shaft.

What kind of engine does a Ranger 4×4 have?

I have a 2001 Ranger EDGE, 4.0 liter engine, 4-Speed 4×4 Auto with about 106,000 miles on it. My 4×4 isn’t working. I flip the switch to 4-High, and the light switches to 4-High, but no power to my front wheels. Stop the truck, put it in neutral, flip it to 4-Low, and it switches over.

What are the four wheel drive warning lights on a Ford Ranger?

• 4L: Four-wheel drive low is engaged. • 4H: Four-wheel drive high is engaged. The airbag warning light on the Ford Ranger should as a system check come on briefly as the ignition is set to on or when the engine has started. It should then go out after a few seconds.

Are there any problems with the Ford Ranger 4×4?

Problems with Ford Rangers can arise with either the low or high 4X4 system or the automatic or manual hubs. If you are having problems with your 4X4, follow these steps to diagnose the trouble.

Why does my Ford Ranger go into reverse?

Spring tension of the shift indicator would pull it out of “park” as soon as the lever was released. Shifter would go into “neutral” and “reverse” at random. Had to shut off the vehicle and restart when I left car even briefly – not something drivers normally do. Vehicle popped into “neutral” about 75 to 100 times and into “reverse” about 50 times.

Why does my Ford Ranger have no power?

I flip the switch to 4-High, and the light switches to 4-High, but no power to my front wheels. Stop the truck, put it in neutral, flip it to 4-Low, and it switches over. I can feel the power difference because it gears lower, but still no power to the front wheels.

Why does my 1994 Ranger not come out of 4Wheel?

I have had this problem with my 1994 from day one of ownership. Chances are it’s the electric motor in the transfer case that is all bound up with dirt and crud. Each year I have my mechanic clean it in the fall. my 1998 will not come out of 4wheel low, the switch on dash doesnt respond as well?

Is there a problem with my Ford Ranger 4×4?

I have a similiar, if not identical problem. My 4WD indicator lights function, and low range engages when selected, but front wheels do not pull. I’ve been told that this may be a rubber bumper stop in the transfer case that is worn that allows the gears to “over shift”. I have had this problem with my 1994 from day one of ownership.

Why is my Ford Ranger not shifting high?

Take it off and check it out, you may just have a bad connection too. My 1998 Ford Ranger 4 liter auto with electronic shift on the fly seems to not be shifting into high or low 4wd. The dash light indicates 4 high but not low. I read the post about solenoid but I am wondering if it could be a fuse problem before the solenoid. Any help appreciated.

What was the problem with the Ford Ranger 4WD control module?

Forum member ‘Rich’ experienced problems with the 4WD control module on his 1996 4×4 Ranger. Rich checked for DTC codes and found none. He worked through the series of pinpoint tests. He pulled the radio for access and disconnect and tested the 4WD switch for resistance in each position.

What are the 4WD lights on a 1995 Ford Ranger?

When you turn on the key in your 1995 and newer Ranger 4×4 with an electronic shifted transfer case, you should see your 4HI and 4LO lights momentarily light up on your dash. When the 4WD lights flash on and off, this indicates that there are 4WD-related trouble codes in the 4WD control module.

What to do if your 4×4 control module is not working?

If the light does not illuminate, check to see if all other dash lights are on – if so, this is the first step for diagnosing a defective 4X4 Control Module. If the 4X4 light on the dash is not on, check to see if the 4X4 ECM fuse is blown (fuse #5 on the inside fuse panel on driver side dash pad).

What should I do if my Ford Ranger 4×4 is not running?