How to check fuel pump signal in gmflash?
How to check fuel pump signal in gmflash?
1. CONNECT PIN1 (BLACK GROUND) TO PIN16 (PINK GROUND) 2. CONNECT PIN32 (RD/WH BATT + ) TO PIN47 (GY FUEL PUMP 12+) THIS WILL POWER THE PUMP TO RUN AND CHECK FOR A FAULTY FUEL PUMP. 3. NEXT, CHECK FOR FUEL PUMP SIGNAL AT THE FUEL SYSTEM CONTROL MODULE. 4. FIND THE DARK GREEN/WHITE WIRE IN PIN13.
What to look for in fuel system control module?
AFTER COMPLETING THE STEPS ABOVE, IF YOU FIND NO POWER AT THE FUEL SYSTEM CONTROL MODULE, AT THE DARK GREEN/WHITE WIRE, MOVE TO THE POWERTRAIN CONTROL MODULE. AT THE POWERTRAIN CONTROL MODULE, CHECK PIN 50, IN THE BLACK CONNECTOR, FOR 12 VOLTS WITH THE KEY ON, FROM THE DARK GREEN/WHITE WIRE.
How to check for a faulty fuel pump?
THIS WILL POWER THE PUMP TO RUN AND CHECK FOR A FAULTY FUEL PUMP. 3. NEXT, CHECK FOR FUEL PUMP SIGNAL AT THE FUEL SYSTEM CONTROL MODULE. 4. FIND THE DARK GREEN/WHITE WIRE IN PIN13. WITH A TEST LIGHT CONNECTED TO THAT WIRE, TURN THE KEY TO THE RUN POSITION.
Where do I find the fuel pump test light?
FIND THE DARK GREEN/WHITE WIRE IN PIN13. WITH A TEST LIGHT CONNECTED TO THAT WIRE, TURN THE KEY TO THE RUN POSITION. IF THE POWERTRAIN CONTROL MODULE IS SENDING THE SIGNAL TO COMMAND THE FUEL PUMP ON, THEN THE TEST LIGHT WILL BE ILLUMINATED. Check for one of the following three conditions. 1. Constant 12v Power 2. Power only when cranking 3.
1. CONNECT PIN1 (BLACK GROUND) TO PIN16 (PINK GROUND) 2. CONNECT PIN32 (RD/WH BATT + ) TO PIN47 (GY FUEL PUMP 12+) THIS WILL POWER THE PUMP TO RUN AND CHECK FOR A FAULTY FUEL PUMP. 3. NEXT, CHECK FOR FUEL PUMP SIGNAL AT THE FUEL SYSTEM CONTROL MODULE. 4. FIND THE DARK GREEN/WHITE WIRE IN PIN13.
AFTER COMPLETING THE STEPS ABOVE, IF YOU FIND NO POWER AT THE FUEL SYSTEM CONTROL MODULE, AT THE DARK GREEN/WHITE WIRE, MOVE TO THE POWERTRAIN CONTROL MODULE. AT THE POWERTRAIN CONTROL MODULE, CHECK PIN 50, IN THE BLACK CONNECTOR, FOR 12 VOLTS WITH THE KEY ON, FROM THE DARK GREEN/WHITE WIRE.
THIS WILL POWER THE PUMP TO RUN AND CHECK FOR A FAULTY FUEL PUMP. 3. NEXT, CHECK FOR FUEL PUMP SIGNAL AT THE FUEL SYSTEM CONTROL MODULE. 4. FIND THE DARK GREEN/WHITE WIRE IN PIN13. WITH A TEST LIGHT CONNECTED TO THAT WIRE, TURN THE KEY TO THE RUN POSITION.
FIND THE DARK GREEN/WHITE WIRE IN PIN13. WITH A TEST LIGHT CONNECTED TO THAT WIRE, TURN THE KEY TO THE RUN POSITION. IF THE POWERTRAIN CONTROL MODULE IS SENDING THE SIGNAL TO COMMAND THE FUEL PUMP ON, THEN THE TEST LIGHT WILL BE ILLUMINATED. Check for one of the following three conditions. 1. Constant 12v Power 2. Power only when cranking 3.
How does a bad ECM affect fuel economy?
Poor Fuel Economy. A faulty ECM disallows your engine from knowing how much fuel to burn in the combustion process. Typically, the vehicle consumes more fuel than it should in this situation. You’ll end up paying more for gas than you would with a functioning ECM. The ECM plays a vital role in engine performance.
What happens if the fuel pump relay fails?
If the fuel pump relay fails, what usually happens is that the oil pressure switch feeds power to the fuel pump and gets the engine started and keeps it running. When this happens, the engine will crank till the oil pressure gets up and the oil pressure switch closes. Fuel pump in-line fuse -20 Amp.
How does the engine control module ( ECM ) work?
The ECM takes the information from the engine’s various sensors, and uses that information to calculate and tune engine spark and fuel for maximum power and efficiency. The ECM plays a crucial role in newer vehicles, where many (if not all) of the essential functions of the car are controlled by the ECM.
