How far can you run a fused spur?
How far can you run a fused spur?
The maximum length allowed for an unfused spur is 3m. The general rule of thumb, is that you can have an unfused spur at each socket, and one at the CU.
How many sockets can be connected to a fused spur?
There is no restriction on the number of sockets that can be supplied from a fused spur as the cable cannot be overloaded, however on a practical basis the use of the sockets would need to be limited to a total of 13A total to avoid the fuse blowing all the time so consideration of expected load would be useful.
Can I use a plug instead of a fused spur?
“The regulations state that the appliance needs to be fused, either with a plug or a fused spur. So as long as the plug sockets are accessible without touching the appliance to turn it off then this is fine, but also a fused spur is fine too.”
Why do you need a fused spur?
Fused spurs are commonly used as an alternative to a conventional socket, for the installation of powerful electrical appliances that can be installed without a plug, such as ovens, washing machines, electric heaters, dishwashers, fridges, and so on.
How many Spurs can I take off a socket?
A spur can be connected to an existing socket, on either a ring main or a radial circuit, providing that socket does not already have a spur. That is only one spur per socket is allowed and the number of spurs must not exceed the number of sockets.
Can you put a spur off a spur?
The easiest way of connecting into a ring circuit is to run a spur cable from the terminals of an existing socket – but you can’t connect it to any socket. The IEE Wiring Regulations are very specific about this. You mustn’t run a spur from a socket that’s already on a spur, or that already supplies a spur.
Can I put 2 double sockets on a spur?
That is only one spur per socket is allowed and the number of spurs must not exceed the number of sockets. A general rule for a ring main is that if you only have two cables in the back of an existing socket then it is ok to spur.
Can I run a washing machine off a spur?
Provided that the spur is directly off the ring main and it is at least 2.5mm cable then this is a “legal” arrangement as far as the regs go. So yes you can do this.
Can you spur off of a spur?
There is no problem in spurring off a fused spur (I think that’s what you mean). The principle is you just need to protect the cable. This week I’ve seen a unfused spur from a socket on the ring to a single socket (in 2.5 6262Y) – then from the single socket to a FCU in 1.5 6242Y for the boiler.
Can you run a spur off a spur?
You mustn’t run a spur from a socket that’s already on a spur, or that already supplies a spur. An alternative to running a spur from an existing socket is to run it from a 3-terminal, 30-amp junction box wired into the main circuit cable.
Is it OK to spur off a spur?
Do You need A 32A socket for a 30A spur?
You can terminate the cable at an industrial 32A socket or a suitably rated switch. Definitely requires an electrician to install to ensure the correct cable rating and protection for the cable and the equipment. You are not going to get what is commonly known as a 30A fused spur.
Can a spur be connected to a radial circuit?
A spur can be connected to an existing socket, on either a ring main or a radial circuit, providing that socket does not already have a spur. That is only one spur per socket is allowed and the number of spurs must not exceed the number of sockets.
Can a spur be connected to a ring main?
A spur can be connected to an existing socket, on either a ring main or a radial circuit, providing that socket does not already have a spur.
How do you wire a spur to a socket?
The spur must be connected to the existing circuit using the same cable as used in the main circuit. You can see how to wire a spur to an existing socket from the images below. The first image is how the back of your double socket should look and the second is the wiring for a spur.