Common questions

Why does my Car start hard when the engine is warm only?

Why does my Car start hard when the engine is warm only?

Valves are an important part in the distribution of fuel into the engine block, after the engine warms there maybe some blockage or expansion from heat. Be sure to check your distributor cap and other electrical connections, sometimes the slightest electrical sensor misread tells the vehicle it’s not working correctly when it really is.

Why does my car not start in the morning?

Used best quality fuel system cleaner 3-4 times when tank was empty (to diagnose the problem) Recently changed oil/oil filter (to make sure I’m using correct viscosity oil) The problem is still there. The reason why I’m not leaning towards fuel pump / filter is because first thing in the morning it starts perfectly.

What happens to my Chey when the engine is cold?

2003 Chey. When engine is cold engine starts and runs just great. Only when engine is starting. After starting it runs a little rough but then it runs fine. When I shut it off I can

When to run the fuel pump before cranking the engine?

Some systems will run the fuel pump for a short period when the drivers door is opened or when the key is turned to the ignition stop before being turned to crank. If this isn’t happening for some reason, you may be having to wait until the fuel pump provides enough pressure at the fuel rail to start the vehicle. My vote is for the injectors.

What causes a Chevy Silverado 1500 to hard start?

As it warms up the idle air control adjusts to this vacuum leak and when the key is off the idle air control resets itself causing a hard start up due to the vacuum leak not being compensated for. Just a possibility 16 people found this helpful. K6, see what I mean by listen to John?

How can I tell if my car starter is running?

Next check for ground at the starter relay control. The relay should only get ground from the PCM when the ignition switch is in the START position. If you find ground in the RUN position, check the ignition switch wiring for your year, model/engine the START wire is NOT hot while the switch is in the RUN position.

Why does my Ford starter keep running even after I Turn Off the engine?

Some Ford owners encounter a situation where the starter run continuously or keeps running even after the engine has started and even after they’ve removed the key from the ignition. At first, this may make you think the starter drive is binding. Or you may think you have a bad starter relay.

Why does my Car start when the engine is warm?

Second possibility also has to do with the injectors. When worn they can get out of resistance spec from the internal wires developing an open condition that gets exacerbated when the engine is warm thus demanding too much current to jump the gaps to fire which would also cause a warm start issue.

How can I tell if my car engine is hot or cold?

It seems like it’s a flooded condition, when starting after a brief shutdown. Like the injector driver from the computer is holding the injectors open. The PCM can’t tell if the engine is hot or cold. Cleaning the throttle body may help, as well as air and coolant temp sensors too.

What makes a Chevy Silverado hard to start?

Even 2-3 lbs. less can cause this concern. This 5.3 engine is also known for the intake manifold gaskets leaking vacuum. This causes a hard start and also high idle in cold ambient temperatures, as well as hesitation off idle and unstable idle when engine hot.

When does a Chevy Silverado pickup start cold?

MY SILVERADO PICKUP STARTS GREAT WHEN COLD BUT WILL NOT START WITH OUT CRANKING FOR PROBABLY AROUND 6 SECONDS. SOMETIMES MORE AND SOMETIMES LESS. IT WILL START BACK UP EASILY RIGHT AFTER YOU SHUT IT OFF BUT ABOUT 5 MINUTES LATER IT WILL NOT START VERY WELL. MY CRUISE QUIT ALSO, DON’T KNOW IF IT HAS ANYTHING TO DO WITH IT.

Why does my air conditioner start up when its cold?

When its cold it is in open loop mode and by default would add extra fuel possibly neutralizing the effects of the small vac leak. As it warms up the idle air control adjusts to this vacuum leak and when the key is off the idle air control resets itself causing a hard start up due to the vacuum leak not being compensated for. Just a possibility

Why is my Chevelle 350 hard to start?

Fuel pump check valve doesn’t maintain pressure in the fuel rail so it boils and then you have to crank excessively to get rid of the vapor before it will start. Bought a 1972 Chevelle 350 a couple years ago. Every time I drove it it wouldn’t restart easily or sometimes not at all unless I waited a while.

Why does the Cold motor start longer than the warm motor?

Reason being, with bleeding injectors, the longer they sit, the more fuel gets dumped into the cylinder (until all the pressure is bled off). The OP would see the issue more on the cold side than on the warm. Also, there shouldn’t be any “gaps to fire” in the injectors. If there are, they wouldn’t fire at all.

What causes fuel pressure to drop on a warm start?

The pintles can wear out and allow fuel to bleed off into the cylinder thus dropping pressure. This excess fuel in the cylinder can cause a flooding condition on warm start which the PCM doesn’t know how to deal with since it expects fuel pressure to be there and thus won’t immediately demand anything from the fuel pump.

Why does it take so long to start a 300K engine?

Sure why not. On high mileage engines (200k to 300k) the pistons ring can wear causing low compression which increases crank time and causes hard starting. This is because the compression ratio is low and it takes time for the engine to gain enough speed cranking by the starter to ignite the fuel air mixture.

What causes a car to have a hot starting problem?

Hot starting problems have five principal causes: Starter Tight Engine Engine Malfunction Fuel problems Electrical The cause can be isolated using the guide at the right. Symptom: Engine doesn’t crank*at all Engine cranks, but very slowly Engine cranks fine, but never fires Engine cranks fine, with intermittent firing * NOTE!

Why is my boat hard to start after warm up?

My theory is a leaky carb float valve (is that a carb or injection motor?) or maybe primer valve, just slightly flooding the engine. At home on the muffs, engine is much easier to start without backpressure on the exhaust. On the water, lifting the hi-idle lever advances the timing, let’s it start right up.

What causes a car to start at low rpm?

Normal voltage at starter when cranking (8.5V or better) Tight engine Defective starter with worn bearings Too much ignition advance at low RPM (Starter will intermittantly strain to turn the engine over.) Engine cranks fine, but never fires Nospark found at the coil connection? (Also check for spark at the distributor

Can a power stroke 6.0 liter diesel have a hard start?

When the FICM starts to fail, the 6.0L Power Stroke will have a hard start or no start issue, rough idle and loss of power. When replacing the FICM, 6.0 Complete FICM Part number: 4C3Z-12B599-ABRM, you must use the Ford IDS scan tool to remove the programing from the bad FICM and reprogram the new FICM and the PCM or get the Pre-Programmed FICM.

What’s the trouble code for a cold Ford?

It may run extremely rich, which you will notice with rough idle and poor MPG. It may also store trouble codes P0172 and P0175. However, once the engine warms up, it runs fine and will restart just fine.

Are there any problems with a 6.0 liter diesel engine?

Below are the most common problems associated with the 6.0 Power Stroke engine. The 6.0L Power Stroke fuel injection system operates on oil pressure, very high oil pressure.

Why does my Ford PowerStroke diesel not start when hot?

Diesel is Power!!! I’ve had two separate issues with a hot start problem. The first time it was a dummy plug and the truck wouldn’t restart until the oil temp was below 150deg using 15 40w oil. I tried and put in 10 40w syn oil and that made it worse and I had to wait till it was below 130deg.

Is there a problem with my Ford diesel?

FORD Diesel ~6.0L & 7.3L~ Troubleshoot Hard or Won’t Start Problems ~Can’t Start Hot/Cold? If playback doesn’t begin shortly, try restarting your device.

Valves are an important part in the distribution of fuel into the engine block, after the engine warms there maybe some blockage or expansion from heat. Be sure to check your distributor cap and other electrical connections, sometimes the slightest electrical sensor misread tells the vehicle it’s not working correctly when it really is.

When the FICM starts to fail, the 6.0L Power Stroke will have a hard start or no start issue, rough idle and loss of power. When replacing the FICM, 6.0 Complete FICM Part number: 4C3Z-12B599-ABRM, you must use the Ford IDS scan tool to remove the programing from the bad FICM and reprogram the new FICM and the PCM or get the Pre-Programmed FICM.

Author Image
Ruth Doyle