Why is my turn signal not working on my 1999 Yukon?
Why is my turn signal not working on my 1999 Yukon?
1999 Yukon; rear turn signal not working. Front working fine, fast blinking indicator, was not the bulbs, was not a loose wiring harness, or dirty connectors (although all worth a quick try) * The board that the 3 lightbulbs plug into, goes bad ! Super easy fix ]
Why is my turn signal not working on my GM Truck?
“No power coming out of BCM for turn signal-tested-found circuit 1334 yellow & black wire shorted to ground-found short located in underhood fuse block-replaced underhood fuse block.” My cost for repair: $600. However, a few weeks later, the left rear turn signal stopped working again. I took it back to the dealer.
Why does my turn signal light not blink?
I have a problem like this on my 2008 Chevy Suburban. Left rear turn signal light does not blink when using the turn signal. The light doesn’t blink when I turn on the hazard flasher. The bulb is good. The fuses are good. I took it to the dealer. They tried replacing the Body Control Module (BCM) but that didn’t fix it.
Where is the turn signal on a GM Truck?
This relay is found behind the fuse panel on the left side of the dash. The easiest way to get to it is Pull the plastic trim around your gauges. You can do this by lowering the steering wheel as low as it can go and then moving the shift lever down all the way. You’ll have to use your key, turn on and then lower. Then carefully pop the trim.
Which is GM original equipment turn signal Flasher?
Video Player is loading. This is a modal window. ACDelco GM Original Equipment Hazard Warning and Turn Signal Flasher is a GM-recommended replacement component for one or more of the following vehicle systems: body-electrical and lighting.
Where is the relay on a 2003 Silverado?
Seems like a Relay starting to go bad. The Orignal part# that I pulled out from my 2003 Silverado is 15764153. 2/4-W/Opt. Trailering. This relay is found behind the fuse panel on the left side of the dash.
1999 Yukon; rear turn signal not working. Front working fine, fast blinking indicator, was not the bulbs, was not a loose wiring harness, or dirty connectors (although all worth a quick try) * The board that the 3 lightbulbs plug into, goes bad ! Super easy fix ]
“No power coming out of BCM for turn signal-tested-found circuit 1334 yellow & black wire shorted to ground-found short located in underhood fuse block-replaced underhood fuse block.” My cost for repair: $600. However, a few weeks later, the left rear turn signal stopped working again. I took it back to the dealer.
I have a problem like this on my 2008 Chevy Suburban. Left rear turn signal light does not blink when using the turn signal. The light doesn’t blink when I turn on the hazard flasher. The bulb is good. The fuses are good. I took it to the dealer. They tried replacing the Body Control Module (BCM) but that didn’t fix it.
Which is GM hazard warning and turn signal Flasher?
ACDelco GM Original Equipment Hazard Warning and Turn Signal Flasher is a GM-recommended replacement component for one or more of the following vehicle systems: body-electrical and lighting. This original equipment flasher will provide the same performance, durability, and service life you expect from General Motors.
What should I do about my blinking turn signal?
Check inside the bulb socket for corrosion, check the plug where the wires connect to the lamp circuit board for corrosion, etc. I haven’t even begun to check it out, except for glancing at a reflection of my left turn signals as I’m driving.
How do you change the bulb on a GMC Yukon?
Open the hood of your GMC Yukon. Unscrew the bolts that hold the air cleaner in place and remove it. Remove the studs that hold the cover that protects the headlight housing from the back. Turn the old bulb counter-clockwise to remove it. Replace it with a new bulb and test it to see if it works.
What kind of bulbs do GMC Yukon fog lights use?
For its high beam headlights, bulbs used include 9005, H6054, and 9008. The fog lights come with either an H3 -55W, PSX26W, PS24WFF, 880, 894, or 9145 bulbs. Before upgrading to LEDs or HIDs, it’s important to ensure that you read the fine print.
It is located on the frame crossmember above the spare tire. It was corroded and the clip was weak. I cleaned it up, put some electronics grease on it and put it back together. Then I used zip ties to hold the connector together. I never had an issue after that.
Is there a turn signal for both left and right?
Although some models use a separate light for the left and right turn indicators, other models use a single light for both turns. If your instrument panel has only one indicator light for both left and right, check the flasher unit. Some vehicle models combine the brake light, taillight and turn signal into one light bulb.
What should I do if my turn signal is not working?
A bolt or unpainted metal bracket will do. Then touch the socket contacts with your test light tip and have your assistant operate the turn lights. The test light should flash. If it does, check the ground connection at the socket.
Why is my brake light and turn signal not working?
@chevy88burban, Katelyn , Switch or replace the bulbs from one side to the other to ensure it is not the bulbs, check the bulb sockets for any corrosion/burnt/damaged contacts.
Why is the brake light the signal light?
On one lamp, it is the brake light, on an other it will be the reverse light, on an other, it will be the signal light. Note, on some trucks the stop light and the signal light will be shared. If the bulbs (lamps) are good, the problem may be a broken wire, or a poor connection somewhere.
