Why does my Ford F-150 have no spark?

If you get no spark via the tester on both towers then the problem could be with wiring or connections or problems with the PCM. You have to determine if you are getting a switching signal from the computer.

What kind of engine does a Ford 4.2 have?

The Ford 4.2-liter V-6 engine, commonly known as the Canadian Essex engine, overcame early gasket problems to become a dependable long-running motor. Those early problems, however, dogged the engine’s reputation until the motor was phased out in 2008. The 4.2 replaced the well-regarded Ford 300 straight-six engines and powered the F-150 pickups.

Where to find cylinder one on Ford F150?

An important thing to understand when finding the location of cylinder one is that it’s going to be the first cylinder in the firing order of the vehicle, and not the first cylinder that you might see when looking at the engine. The P0302 trouble code will trigger the F150’s service engine soon light.

Why is my Ford 4.2 liter engine not working?

The 4.2-liter V-6 engine missing or making a popping noise on acceleration, but may not have a “check engine” light illuminated, may have a coil or fouling spark plug problem. If the engine is vibrating at idle, the problem is likely collapsed motor mounts, which is not uncommon in high-mileage trucks.

What kind of engine does Ford 4.2L V-6 have?

A co-worker has a ’97 F-150 with the 4.2L V-6 with straight drive. It’s an extra vehicle at the house; she normally drives a 2010 Fusion Sport V-6. She had the F-150 at work the other day and started it and heard a gawd-awful clanking noise from the engine. Turned it off and called her husband.

Why does my 1992 Ford F-150 have no spark?

15 people found this helpful. 1992 Ford F-150 5.8L died while driving – replaced ignition coil and ignition module (no luck). there is still no spark. Talked to a mechanic – the signal from the distributor is not being transmitted to the ignition module. Instead of replacing the pickup, I decided to replace the whole distributor. Fingers crossed.

What causes no start on a Ford 4.6L?

If no voltage is present, as your helper cranks the engine, then the cause of no fuel condition is due to either a bad fuse, fuel pump relay, or inertia switch. How To Test The Fuel Pump -No Start Test (Ford 4.6L, 5.4L).

What causes a cranks but not start condition?

TIP 3: The ignition coil is not the only thing that can cause a cranks but does not start condition, when it fails. Other components can fail and provoke a no start. If you have already replaced the ignition coil or the tests in this tutorial show that it’s good, the following tutorial may be of help:

How to test the crank sensor in a Ford 4.6L?

You can find the crank sensor test here: How To Test The Crankshaft Position Sensor (Ford 4.6L, 5.4L). Checking for fuel involves two separate tests. One is to check that the fuel pump is functioning and supplying the correct amount of pressure. The other test is making sure that the PCM is activating the fuel injectors.

What causes a Ford F150 to not start?

In this article I’ll show you a very simple, easy and highly accurate way to see if the ignition coil on your 4.9L, 5.0L, 5.8L Ford F150 (or E150, Bronco, Crown Victoria, Grand Marquis, etc) is fried and causing your vehicle to NOT START or not the cause of the problem.

How to know if your engine has no spark?

First Confirm Your Engine Has No Spark. 1 Disable the fuel system by removing the fuel pump fuse or relay. 2 Insert a spark plug tester into the plug boot and ground it on a piece of metal on the engine. 3 Finally, Have someone crank the engine and watch for spark.

How to troubleshoot a no start Ford 4.9L?

Once you’re tapped in, have a helper crank the engine while you observe your multimeter in Volts DC mode. If voltage is present (12 Volts), then you have confirmed that the fuel pump fuse, fuel pump relay and inertia switch are working perfectly.

What does spark tester look like on Ford F-150?

The tester is only about 15 bucks and looks like a spark plug. You can use the tester directly on the coil pack. This will go a long way in figuring out the problem. If you get no spark via the tester on both towers then the problem could be with wiring or connections or problems with the PCM.

Why do I get no spark from my PCM?

You can use the tester directly on the coil pack. This will go a long way in figuring out the problem. If you get no spark via the tester on both towers then the problem could be with wiring or connections or problems with the PCM. You have to determine if you are getting a switching signal from the computer. 5 people found this helpful.

What causes no spark in the ignition module?

Specifically: You have a No Spark Condition from all of the spark plug wires. No fuel injector pulses from any of the fuel injectors. This is usually caused by a bad crank sensor or a bad module. Your starting point is TEST 1. You have spark from all of the spark plug wires.

What does no spark no start condition mean?

Check that power is reaching the coil packs or ignition coil-on-plug coils. If power is not reaching any of the coil-on-plugs or ignition coil packs, you’ll get a bona-fide ‘no spark no start condition’.

Why does my Ford F-150 have no spark?