How to remove an axle shaft from a Mustang?

Axle Shaft Removal (1994-2012 Mustang typical) STEP 1: Remove the 10 differential housing cover bolts and drain the lubricant from the axle housing. STEP 2: Remove the differential housing cover. STEP 3: Mark driveshaft position and remove driveshaft STEP 4: Remove the rear brakes

How big is the rear axle on a Mustang?

One of the first steps to knowing your Mustang rear axle ratio is knowing which rear end is actually under the backside of your pony car. As we have already covered, all 1979-1985 Fox Body Mustang rear axles featured the 7.5” rear.

How do you put a sway bar on a Mustang?

Put wheel chocks around the front wheels of the Mustang, then lift up the rear end with the jack. Put jack stands beneath the chassis and the rear axle, then lower the jack. Unbolt the rear wheels with the tire iron and pull them off of the axle. Unbolt the sway bar bracket from the frame with the 3/8-inch ratchet and socket.

What was the rear end of a 1979 Ford Mustang?

If you own a 1979-2014 Mustang, then it came equipped with one of the two Ford rear ends – Ford 7.5 rear end or the Ford Mustang 8.8 rear end. All 1979-1985 Mustangs featured the 7.5 rear end. Starting in 1986 Ford introduced the popular 8.8” rear end in the Mustang.

Where can I get 1985 Ford Mustang parts?

See results below for 1985 Ford Mustang Parts. Classic Industries is America’s first choice for 1985 Ford Mustang parts and accessories. Holley’s new series of aluminum double pump carburetors are constructed from aluminum, which compared to their zinc counterpart offer a 38% weight savings.

What kind of rear axle does a Ford Mustang have?

All 79-04 Ford Mustang Rear Ends used 28 spline axles except for the 2001 and 03-04 SVT Cobras – they used a 31 spline axle in their IRS rear end. The 2005-2010 V6 Mustangs with a Ford 7.5 rear end used 28 spline rear axles whereas the 2005-2010 V8 Mustangs with 8.8”rear ends used 31 spline rear axles.

How to remove rear axle universal joint flange?

Remove Companion Flange STEP 1: While holding rear axle universal joint flange with Companion Flange Holding Tool, remove pinion nut. STEP 2: Remove rear axle universal joint flange with Companion Flange Remover. STEP 3: With a soft-faced hammer, drive pinion out of differential pinion bearing and remove through rear of rear axle housing.

How to remove the pinion on a Ford m-4209?

STEP 1: With pinion removed, place differential case (ring gear removed) with differential bearings and differential bearing cups in rear axle housing. STEP 2: Install a 6.75 mm (0.265-inch) differential bearing shim on LH side of subassembly. STEP 3: Install LH bearing cap finger-tight.

What kind of rear end does a Ford Mustang have?

All 1979-1985 Mustangs featured the 7.5 rear end. Starting in 1986 Ford introduced the popular 8.8” rear end in the Mustang. From 1986-2010 the Ford Mustang 8.8 rear end went into all V8 Mustangs (5.0L, 4.6L and 5.4L) and the Ford 7.5” rear end went into all 4 cylinder (2.3L) and V6 Mustangs (3.8L).

How many axles does a Ford Mustang have?

The 2005-2010 V6 Mustangs with a Ford 7.5 rear end used 28 spline rear axles whereas the 2005-2010 V8 Mustangs with 8.8”rear ends used 31 spline rear axles.

What is the rear end gear ratio for a Mustang?

Here are a few things to help you differentiate between a 7.5 & 8.8 rear end. Measure the diameter of the ring gear. A 7.5 Ring Gear will measure 7.5. An 8.8 Ring Gear will measure 8.8. You can also count the splines on the Pinion Gear. A 7.5 Pinion will have 28 splines & an 8.8 pinion will have 30 splines.

What kind of driveshaft does a Ford Mustang use?

The original driveshaft is likely fine as long as it’s not damaged and the U-joints are in good shape. Almost all firstgeneration Mustangs used a singlepiece, steel driveshaft with an integral soundproofing liner on the inside surface of the tube. Tube diameters ranged from 23 ⁄4 to 31⁄2 inches with various lengths and U-joint types.

What’s the gear ratio on a 1979 Mustang?

Use this guide to have your Mustang gear ratio explained! If you own a 1979 to current Mustang, then it came equipped with one of the two Ford rear ends – Mustang 7.5” rear end or the Ford Mustang 8.8” rear end.

How to remove an axle shaft from a Mustang?