Why does my GM airbag light come on?

The bulletin address a problem with the electrical connectors for the airbag system that causes an Airbag Light on or Service Airbag Message to appear. GM will replace the worn/defective connector parts for free as long as your vehicle VIN number is covered by the bulletin (see below for compatibility)

What happens if you ignore the seat side impact air bag light?

When that happens, the seat side impact air bag is fully functional. However, if you ignore the warning light, over time the resistance can increase to a level where the seat side impact air bag may not deploy in a side impact crash. Dealers will replace the front seat-mounted side impact airbag terminals and connector body.

How to turn on the seat airbag light?

Install the blue seals on the body harness and the white seals on the seat airbag harness. Strip the insulation off all four leads 5 mm (3/16 in). Align the seals with the wire insulation. 7. On the body harness, position two FEMALE terminals onto the wires.

How to reset the warning light on a Chevy Silverado?

It is recommended to perform a proper diagnostics check before attempting to reset any warning light, as warning lights are the only way your truck may communicate that there is something wrong. Once you’ve performed the diagnostics check, follow this guide to reset the warning light.

How do I Turn Off the airbag light?

1. Disable the airbag system. 2. Replace connectors on both driver and passenger seats. Then reroute and attach the harnesses to the seat using the service kit. 2. Disconnect connector C308 from driver’s seat cross-beam. 3. Remove the driver’s seat. 4.

Can a GM airbag be replaced for free?

GM will replace the worn/defective connector parts for free as long as your vehicle VIN number is covered by the bulletin (see below for compatibility)

Is the air bag light on on a 2003 Chevy Silverado?

2003 Chevy Silverado air bag dash light on, but get no code when scanned. What might be the issue? Realize you need a code reader which can read your SRS system.

What does it mean when SRS airbag light comes on?

Therefore, when you see the service airbag message pop up, you should immediately get it fixed. What you might also experience with the service airbag message popping up is your SRS airbag light turning on. This may occur if your car was previously involved in an accident that resulted in the crash sensors’ activation without the airbags deploying.

What is the trouble code for GM airbags?

GM has issued a service bulletin to address an airbag light on condition along with the following trouble codes: B0012, B0013, B0015, B0016, B0019, B0020, B0022, B0023, B0026, B0033, B0040, B0042 or B0044 on the vehicles listed below. 2006-2014 Chevrolet Corvette, Impala, Malibu Models (includes Malibu Classic)

What to do if your airbag light is on?

Avoid driving your car if the airbag light is on. Conduct a quick diagnostic by performing the following checks: Charge your battery or replace a faulty battery. Ensure that the passenger occupancy sensor is wired correctly. Check your airbag clock spring (especially if you have a faulty horn). Some airbag issues need professional hands to resolve.

How to reset the air bag on a 2005 Chevy Silverado?

Select the “codes” menu, then select “clear all codes.”. Unplug the scan tool from the vehicle. Start up the engine and check to make sure that the air bag light is no longer on. The air bag system is now reset.

What does it mean when your airbag light is on?

All the same, the most important thing to know is that, an illuminated airbag light indicates a problem in the SRS system. This means that airbags might not deploy in the event of an accident. Here are the common reasons that cause your airbag light to illuminate; 1. Airbag Clock Spring Damage

What to do if your GM airbag light is on?

If your dealer will not cover the repair, contact the GM customer service center. 1. Disable the airbag system. 2. Replace connectors on both driver and passenger seats. Then reroute and attach the harnesses to the seat using the service kit. 2. Disconnect connector C308 from driver’s seat cross-beam. 3. Remove the driver’s seat.

When does the air bag light stop flashing?

The light will flash for exactly seven seconds. Once it is off, you have to turn off the ignition within a second. Turn the ignition on again after three seconds. Repeat this process for two or three times and the airbag light will stop flashing. This is the time you’ll know that it is reset. (Part 1) How To Fix Airbag Light – Fast & Easy!

However, it is best not to drive the car if the SRS light is on. Do not drive the vehicle if the airbag light / SRS light is on. Consider using an OBD2 scanner to reset it or take your car to a professional to take care of the matter. Bonus: ABS light on: Why?

What can a mechanic do about an airbag warning light?

A mechanic can help you to deal with the airbag light by examining the system with the help of the car diagnostic internal system. He will then adjust the airbag sensor or determine what else may be the problem with the airbag system.

Why is my airbag clock spring not working?

An obvious giveaway of a damaged Airbag Clock Spring is a broken horn and an airbag light (unless you have a bad fuse). You will have to remove your steering wheel to fix this one. Luckily, with the right tools, you will be done in under 30 minutes. Make sure to buy the correct Airbag Clock Spring specific to your vehicle.

How to fix your airbag SRS warning light?

A no cost easy way to reset and fix your airbag SRS warning light. Tsukasa Azuma is an awesome car blogger of Car From Japan. He owns a car repair shop at downtown Osaka, and he put all that experience to good use in his sharing posts.

How do you reset an airbag warning light?

Once it is off, you have to turn off the ignition within a second. Turn the ignition on again after three seconds. Repeat this process for two or three times and the airbag light will stop flashing. This is the time you’ll know that it is reset. A no cost easy way to reset and fix your airbag SRS warning light.

How long does the airbag light stay on?

To start the process get your watch ready and turn the ignition switch from “Off” to “On.” Once the airbag light comes on it will stay on for a total of seven seconds. Once it turns off, you will have a second to turn the ignition back to “Off.” After you have the ignition off for three seconds, you will need to turn the key back “On.”

Why is the airbag light on when the seat is vacant?

If the seat is vacant, this light should be on. When the seat is occupied it should turn off implying that the airbag system is online and functioning. If the light is off when the seat is vacant or vice-versa, there could be a problem with the sensor.

What does an illuminated airbag light mean?

All the same, the most important thing to know is that, an illuminated airbag light indicates a problem in the SRS system. This means that airbags might not deploy in the event of an accident.

How do you turn off the airbag light?

Put the key into the ignition and turn the switch to the “on” position. Watch for the airbag light to turn on. It will stay illuminated for seven seconds and then shut itself off. After it shuts off, immediately turn the switch off and wait three seconds.

Why is the airbag clock on the steering wheel?

The airbag clock springs are found on your steering wheel. Its work is to ensure continuity of the electrical wiring with the driver’s airbag. It does this by coiling itself in and out as the steering wheel turns. 2. Why is My Airbag Light On?

What to do if your airbag is not working?

Check your airbag clock spring (especially if you have a faulty horn). Some airbag issues need professional hands to resolve. If you think your car is faulty and the above sensors seem to work fine, consult your mechanic/dealer. Otherwise, I wish you all the best as you try this simple DIY.

Where are airbag codes stored in a GMC?

Below you will find common airbag codes that can be stored in your airbag control module after your vehicle was in an accident.

How to fix the service airbag light on a GMC Sierra?

To fix this error – you need to disconnect both batteries, drop the skid plate, and replace the Front Impact sensor. The sensor was $65 on Amazon. Thanks everyone for all of your support! Send me stuff! The Tools I Use: https://www.amazon.com/shop/bonecrrus… Loading…

How long does it take to reset a GMC airbag?

MyAirbags is proud to offer SRS Airbag Module Reset and Seat Belt Repair services to get your GMC back on the road again safely. Avoid the unnecessary expensive dealership prices and trust in MyAirbags to repair and return your airbag module and your seat belts within 24 hours of receiving it, 100% guaranteed or money back!

Where are the airbags on a GMC?

Left-hand Front Seat Belt Pretensioner High And/Or Low Circuit Short To Ground or Earth OrVoltage (12 volt VSS) Left-hand Roof Panel Airbag Module High And/Or Low Circuit Short To Ground or Earth OrVoltage (12 volt VSS) Left-hand Roof Panel Airbag Module High And/Or Low Circuit Short To Ground or Earth Or Voltage (12 volt VSS)

GM will replace the worn/defective connector parts for free as long as your vehicle VIN number is covered by the bulletin (see below for compatibility)

Why does the service air bag light come on?

Then the DIC message would come on saying Service Air Bag. However this would go away the next time I started the truck and then would come back randomly. I took it to the dealer and they checked it out and said they found no problem with the airbag, and chalked it up to a computer glitch.

Where are the air bag connectors on a GMC Acadia?

The airbag connectors on some 2008 Buick Enclave, GMC Acadia, and Saturn OUTLOOK vehicles, and 2010 Chevrolet Malibu and Pontiac G6 vehicles may wear, leading to corrosion in the connector terminal pins at the connection between the body main wiring harness and the front driver and passenger side impact air bag.

What should I use to keep my airbag light on?

Wrap Woven Polyester Electrical Tape (PET) (preferred) or equivalent anti-abrasion tape or electrical tape around the two exposed wires on the seat harness for a length of 30 mm (1.2 in) from the back of the connector. Continue to wrap the tape around the back of the connector. 15. Slide the conduit back up.

Why does my GM airbag light come on?