How to troubleshoot a GM fuel pump relay?

The following tutorial may be of help: Troubleshooting The Fuel Pump (GM 4.3L, 5.0L, 5.7L) (at: troubleshootmyvehicle.com ). The following links will help you comparison shop for the fuel pump relay:

What should fuel pressure be if fuel pump is not activating?

If the fuel pump relay IS NOT activating the fuel pump, the fuel pressure test gauge will register 0 PSI when cranking the engine. If the fuel pump relay is activating the fuel pump, then it’ll register about 56-62 PSI even if the engine does not start. Any fuel pressure below 50 PSI and the engine will NOT start.

Where are the fuel pump and AC relays located?

The AC relay is located in the same under-hood fuse/relay box the fuel pump relay is in (see illustration above). Locate the fuel pump and AC compressor relays in the under-hood fuse and relay box. Swap the relays .

What is the PSI of the fuel pump?

Why is my fuel pump relay outside the fuse box?

If it’s located inside the engine bay, which can get hot from the engine’s heat, the heat can impede the relay’s performance. In addition, in the rare cases where you will find the relay placed in the engine bay but outside the fuse box, it will be exposed to heat plus dust and dirt.

How to test the fuel pump relay Chevy Silverado?

How To Test The Fuel Pump Relay ( Chevy/GMC Pick Up) Fuel Pump Circuit Diagram. The following tutorial may be of help: Troubleshooting The Fuel Pump (GM L, L, L) (at: schematron.org). Backfiring Distributor Wiring Diagram l 2wd C Asked by Pelacaman · Chevy Silverado Fuel Pump Wire. Electrical Problem.

The following tutorial may be of help: Troubleshooting The Fuel Pump (GM 4.3L, 5.0L, 5.7L) (at: troubleshootmyvehicle.com ). The following links will help you comparison shop for the fuel pump relay:

What should fuel pressure be when fuel pump relay is activated?

If the fuel pump relay is activating the fuel pump, then it’ll register about 56-62 PSI even if the engine does not start. Any fuel pressure below 50 PSI and the engine will NOT start. If you do see any fuel pressure below 50 PSI, the fuel pump although working, is not creating enough pressure to start the engine and is defective.

Can a 6.5L fuel lift pump be replaced?

This video is about replacing the 6.5L diesel engine fuel lift pump on GM full size old body style (OBS) trucks from Chevrolet and GMC. In this scenario the vehicle was operating fine, until the fuel filter was replaced, at which point the lift pump is discovered to be defective during bleeding air from the new filter.

What kind of fuel pump does a Chevy Tahoe have?

This tutorial will show you how to test the fuel pump relay on your 1997, 1998, 1999 Chevrolet/GMC full-size Pick Up, Suburban, Tahoe, or Yukon. It’ll also show you how to bench test the fuel pump relay in a step-by-step way to find out if it’s defective or not.

Where is the fuel pump fuse box located?

The engine’s or the dashboard fuse box is usually a long black box containing a fuel pump relay and various other fuses and relays. For different vehicles, the fuel pump relays can be located in different places.

Where is the Chevy P30 fuel pump relay?

Well the book shows 3 places it could be. 1 where I already said, 2 under the doghouse on drivers side, 3 inside of the frame rail in the rear. The relay should have 4 but could have 5 or 6 wires in it. The orange wire is 12v power, black= ground, dk/grn/wht is switched power, gray goes to the pump.

How can I Fix my Chevy fuel pump?

Ask a Chevy Mechanic for Answers ASAP By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them. My Chevy has no power to fuel pump. How can I fix it? no power to fuel pump… Submitted: 10 years ago. Category: Chevy

Is there no power to the fuel pump?

No power to the fuel pump and the fuel relay is not getti… Q: No power to the fuel pump and the fuel relay is not getting power. My car has 190000 miles.

Where is the power wire on a Chevy fuel pump?

Want to make sure its a 5.7L engine with the classic style truck and not the new style truck with the 6.0L Right? On the fuel pump connector, the gray wire is the power wire. The thick black wire is the ground.

Why is my Chevy fuel pump not working?

The thick black wire is the ground. If the fuel pump has been replaced before, It could have had the connector replaced with the new style ( old style is square and the new style is more rectangle/flat) and where they splice the new connector in could have gone bad.

Why is the fuel pump and relay not working?

The ignition circuit, which includes the ignition switch, controls power to many components, including the fuel pump and relay. If there is an issue with the switch or the circuit, perhaps a wiring problem, then power to the fuel system may be cut off.

No power to the fuel pump and the fuel relay is not getti… Q: No power to the fuel pump and the fuel relay is not getting power. My car has 190000 miles.

How to troubleshoot the fuel pump on a GM 4.3L?

Troubleshooting the fuel pump (GM 4.3L, 5.0L, 5.7L) (for ‘Spider’ fuel system equipped vehicles). How To Test The Fuel Pump On GM TBI Fuel Systems (for throttle body fuel injection fuel system equipped vehicles).

Is there an ECM signal to the fuel pump relay?

The fuel pump relay works as it should. I always have power to Pin 30. I believe the ECM tells the relay to work via the green/black wire to Pin 85. This should happen for 2 seconds when the key is turned on. I have tested this when the issue is occurring and have confirmed that no signal is being sent from the ECM.

How to test a GM 4.3L fuel pump?

More GM 4.3L, 5.0L, and 5.7L Tutorials. It’s very important that you start off your fuel pump relay diagnostic by first testing the fuel pump pressure with a fuel pressure test gauge. If the fuel pump relay IS NOT activating the fuel pump, the fuel pressure test gauge will register 0 PSI when cranking the engine.

Where is the fuel pump control module located?

It is often found in the fuse box located in the engine bay and functions as the primary electronic switch that controls power to the fuel pump. The fuel pump relay is usually controlled by the ignition or Powertrain Control Module, and when switched on, will provide current to the fuel pump so that it may function.

How many pins does a fuel pump relay have?

The fuel pump relay does often have 4 pins, and in this case, it is often easy. If your relay has more pins and not the same numbers mentioned here, you need to check a wiring diagram. Lift it and check under it for the numbers 30, 85, 86, and 87. If you locate these numbers, you can put the fuel pump relay back.

How to test a GMC fuel pump relay?

TEST 1: Swapping Out The Fuel Pump Relay. TEST 2: Making Sure The Fuel Pump Relay Has Power. TEST 3: Bypassing The Fuel Pump Relay. TEST 4: Bench Testing The Fuel Pump Relay. Fuel Pump Circuit Diagram. Where To Buy The Fuel Pump Relay. More GM 4.3L, 5.0L, and 5.7L Tutorials.

What kind of parts do I need for a 1999 GMC?

1999 GMC Parts | RockAuto ALL THE PARTS YOUR CAR WILL EVER NEED Show Prices In US Dollars ($)Australian Dollars (AU$)Brazilian Real (R$)Canadian Dollars (CAD$)Swiss Francs (CHF)Euros (€)British Pounds (£)Japanese Yen (¥)Mexican Pesos (Mex$)Norwegian Krone (kr)New Zealand Dollars (NZ$) EnglishEspañolDeutschFrançais Help Order Status & Returns