How can I change the oil in my air compressor?
How can I change the oil in my air compressor?
Remove the air compressor. Remove the drain plug on the side of the compressor and drain the oil into a cup. Remove the drain plug on the side of the new compressor and add the same amount of oil that drained from the old compressor, plus 2 ounces.
How do you remove an air compressor from a car?
Push the pulley away from the belt and remove the belt from the air conditioning pulley only. Remove the four bolts securing the air compressor to the engine bracket using a socket. Remove the air compressor. Remove the drain plug on the side of the compressor and drain the oil into a cup.
How do you install a new AC compressor?
Install the new compressor in reverse order. The warranty may also require you to change the orifice tube and receiver/dryer. Install and tighten the compressor-mounting bolts and hook up the electrical connectors. Replace the refrigerant tubes’ O-rings and lubricate with the proper oil.
How do you replace the refrigerant in an AC compressor?
Replace the refrigerant tubes’ O-rings and lubricate with the proper oil. Reinstall the refrigerant lines and put the belt back on the pulley. Pull a vacuum through the system to eliminate any residual atmospheric air or moisture.
Can you add Freon to a 2002 Ford Windstar?
If there is a problem with your compressor or evaporator, adding freon will not restore cooling. How to add freon to your 2002 Ford Windstar: hook up the can of refrigerant (likely r-134a) to the low pressure port. When your compressor kicks on, add freon to the correct pressure.
What to do if your Ford Windstar has a leak?
When the air conditioner in your 2002 Ford Windstar starts blowing hot air, you likely have a freon leak. Recharging the freon in your AC system is an inexpensive and easy first step to restoring the cooling capacity of your A/C system. Most refrigerants include a leak sealer that will seal small leaks in addition to filling the R134a refrigerant.
Why is my Ford Windstar blowing hot air?
Video Description When the air conditioner in your 2002 Ford Windstar starts blowing hot air, you likely have a freon leak. Recharging the freon in your AC system is an inexpensive and easy first step to restoring the cooling capacity of your A/C system.
What kind of refrigerant do I need for my Windstar?
Recharging the freon in your AC system is an inexpensive and easy first step to restoring the cooling capacity of your A/C system. Most refrigerants include a leak sealer that will seal small leaks in addition to filling the R134a refrigerant. The A/C system in your Windstar consists of a compressor that is belt-driven, an evaporator and freon.
How do you install a new air compressor?
Install the new orifice tube in the same manner and plug the two lines together again until they snap lock. Install the air compressor and tighten the four bolts. Place some oil on the O-rings on the manifold and install the manifold lines to back of the compressor. Tighten the single retaining bolt with a socket.
How do you add refrigerant to a new gas compressor?
Remove the drain plug on the side of the compressor and drain the oil into a cup. Remove the drain plug on the side of the new compressor and add the same amount of oil that drained from the old compressor, plus 2 ounces. If no or very little oil has drained from the old compressor, add 7 ounces of refrigerant oil to the compressor.
How do you replace an AC compressor in a car?
Remove the compressor’s mounting bolts and pull the unit from the vehicle. Install the new compressor in reverse order. The warranty may also require you to change the orifice tube and receiver/dryer. Install and tighten the compressor-mounting bolts and hook up the electrical connectors.
Can a recovery machine be used for an AC compressor?
Recovery machines are specialized equipment that are limited to AC shops—you may need to take your vehicle in for this step before going any further. Remove the negative battery cable from its post. Remove the bolt at the compressor that secures the refrigerant lines and inspect the lines carefully for dirt or signs of wear.
Do you need serpentine belt to replace AC compressor?
Remember to wear safety glasses and latex gloves before you get started! Locate the AC compressor and remove the serpentine belt from the compressor’s pulley. You may need a serpentine belt tool to work the tensioner and relieve pressure on the belt so you can take it off. You’ll need to evacuate the system’s refrigerant using a recovery machine.
What’s the best way to charge an AC compressor?
Put a thermometer in the interior AC vent while running the system on max setting and high blower speed. When the system is cooling at 30 to 36 degrees, your AC is charged.
