Why does my cat school bus not start?
Why does my cat school bus not start?
Still haven’t had a scanner on it but the cat dealer thinks the heui pump and all 6 injectors need replacing ($3600.00 parts only). He says the low oil has killed the pump and spread metal cuttings throughout the injectors.
Is there any warranty on Cat 3126 cranks?
The diagrams I have seen don’t look exactly like my configuration. No warranty! Any thoughts?
Is there a problem with my C12 diesel truck?
Discussion in ‘ Heavy Duty Diesel Truck Mechanics Forum ‘ started by raferko, May 9, 2019 . okay so I have a c12 with a fuel problem, it runs rough/sounds like it has a miss almost and is low on power, the fuel filter and water separator are new.
What are the codes on a cat 3126?
The intake heater relay energizes when it is supposed to and I can feel the intake get a little warm to the touch after a couple of cycles so I believe it is probably ok. The cruise/rpm switch method revealed 2 codes. #39 and #38. I don’t have access to a code reader.
How to restart Pi-hole / FTL issue # 12?
Type run debug to start FTL (you should see some lines of text and FTL should start successfully). You can now close the terminal (Ctrl+A and then D to detach) and come back later using (screen -r) when it has crashed If it has crashed, copy&past the terminal output, and type also backtrace and post the output
Is there a way to restart FTL after 12h?
There should be away to restart it via web ui like you can whit DNS, FTL is always offline after like 12h for me. This comment has been minimized. So far FLT goes offline after 8h uptime This comment has been minimized. Check the log to see if you can figure out why it’s crashing. This comment has been minimized.
How to run run debug to start FTL?
Type run debug to start FTL (you should see some lines of text and FTL should start successfully). You can now close the terminal (Ctrl+A and then D to detach) and come back later using ( screen -r) when it has crashed Hopefully, this gives enough information so we can do proper debugging. This comment has been minimized.
What kind of engine does a cat 3126 have?
I have a 3126 in a 2004 Ford that was running fine when I parked it. Tried to start it after is sat for a couple of weeks. The engine cranks like it should but makes no signs of starting.
What should I do if my hydraulic system is not working?
Hydraulic systems dissipate heat through the reservoir. Therefore, the reservoir fluid level should be monitored and maintained at the correct level. Check that there are no obstructions to airflow around the reservoir, such as a build up of dirt or debris. It is important to inspect the heat exchanger and ensure that the core is not blocked.
What makes a cat 902 compact wheel loader so good?
With the VersaLink™ loader linkage and contoured hood, these machines offer unmatched visibility to the ground, enabling the operator to easily see the work being done. Ergonomically designed joystick and low effort pilot hydraulics reduce fatigue and increase comfort. Three cab options and two canopy options are available. pg. 4 Power Train
Why is my hydraulic valve not unloading properly?
Consider the following when troubleshooting these valves because a valve fails to completely unload a pump: • Valve setting is too high. • Pump does not build up to the unloading valve pressure. • Valve spool binds in the body.
Hydraulic systems dissipate heat through the reservoir. Therefore, the reservoir fluid level should be monitored and maintained at the correct level. Check that there are no obstructions to airflow around the reservoir, such as a build up of dirt or debris. It is important to inspect the heat exchanger and ensure that the core is not blocked.
What are the symptoms of a hydraulic system failure?
Many of the failures in a hydraulic system show similar symptoms: a gradual or sudden loss of high pressure, resulting in loss of power or loss of speed in the cylinders. The cylinder (s) may not move at all, or if they do they may move too slowly or may stall under light loads.
What happens when cavitation occurs in a hydraulic system?
The consequences of cavitation in a hydraulic system can be serious. Cavitation causes metal erosion, which damages hydraulic components and contaminates the fluid. In extreme cases, cavitation can cause mechanical failure of system components.
Can a clogged intake line cause a hydraulic failure?
In extreme cases, cavitation can cause mechanical failure of system components. While cavitation can occur just about anywhere within a hydraulic circuit, it commonly occurs at the pump. A clogged inlet strainer or restricted intake line will cause the fluid in the intake line to vaporize.
