Common questions

How much does a 671 Detroit weight?

How much does a 671 Detroit weight? 2,185 lb Engine characteristics The engine's compression ratio is 18.7:1 with a 4.250 inch bore and a 5.00 inch stroke. The engine weighs 2,185 lb (991 kg) and is 54 inches long, 29 inches wide and 41 inches tall. At 2,100 revolutions per minute the engine is capable of producing 230 horse power (172 kilowatts). Is the Detroit Diesel 6-71 a sport fishing boat? Many years later while I walked the docks at Pier 66 in Fort Lauderdale, Florida, that familiar racket stopped me in my tracks — first in mono as the...
Easy lifehacks

Can a tractor be used to remove fence posts?

Can a tractor be used to remove fence posts? It’s also possible to remove fence posts by chaining them to the front-end loader of your tractor. While this works well in many cases, the three-point hitch can be stronger, and there is always the risk that the rear end of your tractor will lift off the ground, which can obviously be dangerous. What to do if you cant pull a fence puller? If you end up unable to tighten the straps because you’ve tightened too far for the ratchet strap, you can put a strap in place over the old...
Easy lifehacks

Why is there no engine braking?

Why is there no engine braking? Engine braking is prohibited in some areas because of the loud noise it creates. Typically, when an interstate travels near a residential area is when you will see the signs prohibiting the action. Mostly, engine braking is regulated because of residential areas located close to tolls roads and interstates. Can you drive with the Jake Brake on? You might see the sign Jake Braking Prohibited, No Jake Brakes within City Limits, or No Engine Braking within City Limits in your travels across California. It's kind of like a machine gun or jackhammer, but this...
Easy lifehacks

How did the first hydraulic press work?

How did the first hydraulic press work? First Hydraulic Press Bramah patented a design for a hydraulic press in 1795. The press used a hydraulic cylinder to generate compressive force, which then was used to produce mechanical force. Bramah's press quickly replaced the steam hammer as the machine of choice for metal forging in his time. Who is the father of hydraulics? Along with William George Armstrong, he can be considered one of the two fathers of hydraulic engineering....Joseph BramahNationalityEnglishKnown forhydraulic press Can a hydraulic press crush a diamond? Diamonds can be crushed with any hard enough object that is...
Easy lifehacks

How does a caterpillar check engine diagnostic work?

How does a caterpillar check engine diagnostic work? Caterpillar Electronic Engines have self diagnostic capability. When the system detects a problem, the CHECK ENGINE/DIAGNOSTIC (YELLOW) lamp activates. In most cases a diagnostic code will be stored in permanent memory within the ECM. Why does my truck engine not start when I replace the ECM? NOTE: A new ECM comes with an unprogrammed Personality Module in it. If the ECM has been replaced, the ECM WILL NOT COMMUNICATE and the ENGINE WILL NOT START until the integral Personality Module has had software flashed into it. 4. Where can I Find my...
Easy tips

Is the D6 steering clutch the same as the D5?

Is the D6 steering clutch the same as the D5? THAT COMES FIRST. The D6 steering clutches ( D6 4R, 5R, 8U, 9U) and D6B 37A and 44A are the same design as the later D5 model machines, using the same inner driving drums, same bimetallic friction discs, same steel separator plates, clutch springs, and even the same brake drum and brake linings! What kind of undercarriage does a Caterpillar crawler have? UNDERCARRIAGE IS NOT AS GOOD AS IT LOOKS. FOR GOOD UNDERCARRIAGE SEE THE D4 4G THE MACHINE. ENGINE ROTATED SO WE GAVE IT A TEST RUN. OF THEIR...
Common questions

What kind of engine does a Massey tractor have?

What kind of engine does a Massey tractor have? It has a Continental 4.3L 4-cyl gasoline 45 hp engine, with liquid-cooled vertical I-head, 2 wheel drive, tricycle front, manual steering, with mechanical brakes, the rear hitch is the Massey Hitch-All type, front tires are 5.50-1... What kind of tractor is a 1946 Massey junior? Hello! I'm new to the forum, and I'm probably not going to be very active, but i have some questions about a 1946 Massey Harris 102 junior that i bought as a non-runner some time ago. Where to find the serial number on a Massey 44?...
Common questions

What kind of hydraulic fluid goes in a New Holland skid steer?

What kind of hydraulic fluid goes in a New Holland skid steer? MULTI G is a multi-purpose fluid that has been recommended in New Holland and Ford oper- ator manuals for many years. It's recommended for current low-and medium horsepower trac- tors and loader backhoes. It helps ensure the best performance of your transmission, PTO clutches, wet brakes and hydraulic system. How do you check hydraulic fluid in a New Holland skid steer? Carefully remove the cap from the reservoir, remove the dipstick, and wipe it clean using a dry piece of cloth. Put it back and draw it out...
Easy lifehacks

How long does a Cummins ISM 500hp motor last?

How long does a Cummins ISM 500hp motor last? Over 12 years, this motor has had about $7K of EGR work (valve, bellows and stuff). It is also on its 3rd Turbo for $8K. First one lasted 10yrs and 70000 miles. Second one last 9 months and 3500 miles and the third one is going strong at nearly 2 yrs and 14,000 miles. How to tell if a Cummins engine is an ISM? The ISM is easy to identify visually: The slanted design of the valve cover isn't shared by any other engine. Location: Over the next hill, around the...
Common questions

Can a left rear axel be replaced on a New Holland skid steer?

Can a left rear axel be replaced on a New Holland skid steer? The left rear and front right axel seals will be replaced because of a leak. The left rear axel was easily removed and the seals are on order. There is a oil seal and a dust seal, both will be replaced. How can I Turn my steering wheel to the left? Turn the wheel all the way to the left and hold it there tightly. Then loosen the hose line and and turn the wheel all the way to the right to bleed it out with hope...