Common questions

How do you remove a solenoid valve from a transmission?

How do you remove a solenoid valve from a transmission? Use a wrench and a screwdriver to remove all bolts and screws that are holding the block-like assembly in place. Carefully pull the solenoid valve body off the underside of the transmission and place it on a flat work surface. Where are the solenoids located in an automatic transmission? The Transmission shift solenoids are located inside the valve body of your automatic transmission. They are integrated into the valve body, and on some car models, you can see them without removing the valve body, while on others, you have to...
Other

What should I do if my engine is hydrolocked?

What should I do if my engine is hydrolocked? An engine hydrolock could be as little as the cost of new spark plugs and an oil change. Or, if the engine was damaged when the hydrolock happened, you may need to replace the engine at a cost of thousands of dollars. Can a dash cam drain your car battery? Using a hard wire kit for parking mode features MIGHT drain your car battery depending on how it is setup. With a hard wire kit that is made for a dash cam using parking mode, it will usually have 3 wires,...
Other

How do you start a Dodge Ram 1500?

How do you start a Dodge Ram 1500? What you need to do is link the ignition wire on/off the wire to the battery wire. You do that by twisting both of the wires together. Now strip the starter wires about half an inch. Do wear plastic hand gloves before doing this to prevent any electric shock. Why does my Ram 1500 not start up? Turn the key, gauges radio everything but the starter comes on. The trick I found I'd if I hold the ignition switch to the starting position, 15, 30, a minute, sometimes longer, it'll finally crank...
Other

What transmission does the RAM srt10 have?

What transmission does the RAM srt10 have? Dodge Ram SRT-10RelatedDodge Ram 1500PowertrainEngine8.3 L (505 cid) V10Transmission6-speed manual 4-speed 48RE automatic What is the horsepower of the third generation Ram srt10? 500 @ 5,600 rpm Horsepower. When was the first Dodge Ram SRT 10 made? The first SRT-10 was produced November 10, 2003. Ram SRT-10 production ended after the 2006 model year Total production for the 2004 Dodge Ram SRT-10 was 3,057. For 2005, the total production was 5,113 and the 2006 total production was 1,973. Over the 3-year lifespan of this truck, 10,046 Dodge Ram SRT-10s were manufactured. Where are...
Easy lifehacks

How to change the brakes on a Dodge Ram?

How to change the brakes on a Dodge Ram? 1 Elevate the vehicle off the ground. Loosen the lug nuts on the wheels before jacking up the truck. 2 Remove wheels. Now that the vehicle is elevated, you can remove the wheels where you will be changing the brakes. 3 Depress piston on caliper. 4 Wash down brakes. 5 Remove brake caliper. How does the brake fluid work on a Dodge Ram? Pressing the brake pedal applies pressure to push the master cylinder piston forward, and transfers the brake fluid to each of the four brakes via the brake lines....
Common questions

What causes fuel sensor failure on Dodge Ram 1500?

What causes fuel sensor failure on Dodge Ram 1500? After looking around online, seems many vehicles get this error and Sea Foam or Techron (black bottle) seems to clear it up in some cases due to sulfur build up from shitty gasoline. Anyone else have luck with this DIY method? How big is the fuel tank on a Dodge Ram? Car fuel tank capacity: 98.0 litres (25,76 gallons). The above information shows the orignial Dodge Ram fuel consumption, miles per gallon or litres/ km that are taken from vehicle owners manual (book car). Consumption can be affected depending on the...
Easy tips

What should I do if my starter makes noise?

What should I do if my starter makes noise? Though usually the flywheel had good and bad spots, its grind,normal,grind normal,ect... Pull the lower inspection cover off and look at the flywheel teeth. Alternatively you could pull the starter and check it out with a mirror or camera if you don't have a jack for some reason. Why does my car starter make a grinding noise? Since you mentioned that there was a new starter installed in your car, it is unlikely that it is the cause of the grinding noise you are hearing. How can I swap out my...
Most popular

How to get aftermarket bumpers for Dodge Ram 2500?

How to get aftermarket bumpers for Dodge Ram 2500? If you need help deciding on what you want give us a call at 1-720-895-1744. As a family-owned company, we are available Monday-Friday to help you pick the best option for your truck. Our dedicated team will find you the front or rear Aftermarket Bumpers for Dodge Ram 2500 that works best for you. Can You flush mount a Dodge truck bumper? Flush mount refers to light mounting option, not the fit of the bumper on the truck.Hammerhead Bumpers are made to order. Once an order is submitted, it cannot be...
Other

How much does an 8.5 ” rear end cost?

How much does an 8.5 " rear end cost? The going rate for the 8.5” rear end used is usually between $800 - $1200, depending on if it’s an open differential or a posi differential. The 8.5” are becoming harder to find and typically sell fast when someone posts them for sale. If you are fortunate enough, you can find one in a junkyard, which is how I came about mine. When did the 8 3 / 4 inch rear end come out? Originally created by Chrysler in 1957, the 8 3/4-inch rear was used in many Chrysler cars and...
Easy tips

How can I tell if I need to add coolant to my radiator?

How can I tell if I need to add coolant to my radiator? Check the freezing and boiling point of your coolant. Over time, the ability of your radiator fluid to absorb and dissipate heat declines. You test the freezing and boiling points with an antifreeze hydrometer. See the directions under "Checking the Coolant Protection Level." Add coolant as needed. What should I do if my radiator fluid level is low? If the level is low, pour the antifreeze directly into the tank, not the radiator. If your vehicle doesn't have an overflow tank, remove the radiator cap and check...