Easy lifehacks

How do you take a seat belt buckle off?

How do you take a seat belt buckle off? Remove the seatbelt buckle mounting bolt with a socket and wrench or Torx wrench. Turn the bolt counterclockwise until it can be removed from the mounting hole. Remove the old seatbelt buckle from the vehicle. How to turn off the seatbelt alarm on a Ford Explorer? Insert the key and turn the power on, but do not crank the engine. There is a knob on the dash panel that toggles your trip and total odometer reading, hold and press this button until it says "odo". Turn the key off and then...
Easy tips

How many quarts of oil does a Ford Econoline take?

How many quarts of oil does a Ford Econoline take? 7 quarts. . . (with filter)After refill check oil level. What kind of transmission is in a 2008 Ford Focus? The Focus comes with a five-speed manual transmission and an optional four-speed electronically controlled automatic transmission. How many quarts does a Ford Focus 2008 take? 4.5 quarts Capacity: 4.5 quarts (with filter)After refill check oil level. How many quarts of oil does a Ford v10 take? According to my technical source at Ford, all of the V-10 6.8L engines have a six-quart oil capacity with filter change. What type of...
Easy lifehacks

What size wire do I need for 200 amp sub panel?

What size wire do I need for 200 amp sub panel? Per Article 250 of the NEC , The minimum size for a grounding conductor for a circuit protected by a 200 amp breaker is #6 copper or #4 Aluminum. This conductor may need to be increased in size for any of several reasons, including the length of the run, available fault current or other reasons that would fill a book. What gauge wire do I need for a subpanel? The cable must have a wire gauge sufficient to the amperage of the subpanel—a 100-amp subpanel requires #4 copper wires...
Easy lifehacks

How do you read the codes on a 1993 Ford Ranger?

How do you read the codes on a 1993 Ford Ranger? How Do I Read Trouble Codes on a 1993 Ford Ranger?Locate the two plugs required to perform the test on your Ranger. Connect a wire from the negative battery terminal to the STI. Turn the key in the ignition to the "Run" position. Look at the Ranger's check engine light. Write each of these numbers down. How do I read Trouble Codes on a 1993 Ford Ranger? Look at the Ranger's check engine light. It will blink multiple times and then stop. The light will flicker to give a...
Easy lifehacks

Why is the OBDII port not working on my Ford Expedition?

Why is the OBDII port not working on my Ford Expedition? All of my cigarette lighter ports have power as does the OBDII port. There is just no communication. I noticed there is a 4-pin gray connector taped back behind the OBDII port and was wondering if something needed to be plugged into that as well to enable the reader to read the codes from the PCM. Why is the OBD II scanner not communicating? Check the fuse box (Power Panel), it might be the reason why PCM isn’t able to receive power as well as communicate. What to do...
Other

Are all Ford Explorers 7 seaters?

Are all Ford Explorers 7 seaters? The three-row Explorer seats seven people, or six if you opt for second-row captain's chairs. Cloth upholstery and power-adjustable front seats come standard. When was the third row added to the Ford Explorer? For 1997, a third-row seat was introduced as an option; expanding seating to seven passengers, the design was only offered in export markets. For 1998, the exterior of the Ford Explorer was given a mid-cycle update. Are there heated front seats in Ford Explorer? Heated front seats were a new extra for both the Sport Trac and the two-door Sport wagon....
Other

What PSI should Ford Expedition tires be?

What PSI should Ford Expedition tires be? Ford recommends that You inflate the tries on Your expedition to 35psi per tire. What is the ideal tire pressure for SUV? Since maintaining your tires is so important to your safety and your car's overall performance, it's important to know what tire pressure is right for your vehicle. Air pressure in tires is measured in pounds per square inch, or PSI; usually, the recommended pressure ranges between 30 and 35 PSI. What is the tire pressure for a 1999 Ford Expedition? 1999 Ford Expedition XLTFront TireRear TireRecommended Tire Pressure30 psi35 psiAcceptable Winter...
Easy tips

What happens if my oil pressure switch is bad?

What happens if my oil pressure switch is bad? Oil pressure switches can develop external leaks (that is, they can leak oil onto the engine) and/or the switch can fail internally such that the switch either fails to warn of low oil pressure or the switch goes off prematurely and illuminates the oil pressure warning light when in fact nothing is wrong. What causes oil pressure sensor to leak? Oil leaks: A bad oil pressure switch or sender may leak engine oil. Oil leaks can be caused by a number of issues, so a professional inspection is order here. What...
Easy lifehacks

Why is my Honda Odyssey keyless entry not working?

Why is my Honda Odyssey keyless entry not working? Now they do not unlock anything. This is on my 2001 LX with the kit 08E61-S84-100 added by the previous owners at the date of purchase. Any ideas other than replacing the module? What to do if your keyless entry remote is not working? So before you go out and buy one, try this quick fix that worked for Redditor diggalator, and cost absolutely nothing. Basically, he pried the remote apart and took out the board, noticing that the 'Lock' and 'Unlock' buttons had come loose. Why does my key fob...
Most popular

Why are the fuses not blowing on my amplifier?

Why are the fuses not blowing on my amplifier? If the battery fuse blows 'as soon as it's inserted into the fuse holder' (amplifiers off), the problem could be anywhere in the power distribution line. If the system is set up as shown below, and the fuses in the dblock are not blowing, the problem is likely a direct short to ground between the main fuse block and the dblock. When to replace a fuse in an amp? When an amp blows a fuse (or fuses, for amps with multiple fuses), you should replace the blown fuse with a fuse...