Most popular

What causes a Dodge Challenger engine to misfire?

What causes a Dodge Challenger engine to misfire? Something is causing cylinders to misfire at random, which is a lot less cut and dry than a cylinder specific misfire code. The P0300 Dodge trouble code will trigger the Challenger’s service engine soon light. The vehicle itself may begin to run rough. It depends on how serious the misfire is. How much does a Dodge Challenger SRT8 cost? Monthly Estimate based on a 4.4% rate for 60 months, $23,995 vehicle price, $0 down payment, $0 trade-in, $0 sales tax. Gilbert was extremely helpful with any and all questions my bf and...
Easy tips

How to install a crankshaft positioning sensor on a 99?

How to install a crankshaft positioning sensor on a 99? Disconnect the negative battery cable using a 13 mm wrench and lay it beside the battery so it cannot accidentally touch the battery terminal and cause sparks. Disconnect the electrical connector from the sensor located on top of the transmission bell housing angled slightly to the driver side of the truck. What does the CKP sensor on a 1999 Dodge Durango do? The crankshaft position (CKP) sensor in your 1999 Dodge Durango provides a cranking signal to the onboard computer that is used, along with the camshaft position sensor, to...
Common questions

How much does it cost to replace intake manifold runner?

How much does it cost to replace intake manifold runner? How much does it cost to replace a intake manifold runner control? Know what price you should pay to get your vehicle fixed. The average cost for an intake manifold gasket replacement is between $427 and $558. Labor costs are estimated between $334 and $423 while parts are priced between $93 and $135. What was the code for the P2004 intake manifold runner? 2009 Doge Journey SE, 2.4L V4 with 87000 miles Code 1 � p2004 "Intake Manifold Runner Control Stuck Open Bank 1" - I replaced the intake manifold...
Common questions

What are the specs of a Dodge Ram 3500?

What are the specs of a Dodge Ram 3500? (c) Not available on 3500 SRW. (d) Meets Federal heavy-duty diesel emission control requirements. (e) Meets California medium-duty vehicle engine certified diesel emission control requirements. Hydraulic control, electronically controlled governor overdrive, overdrive lockout and converter clutch Is the Dodge Ram 2500 a Cummins truck? Cummins Diesel With No Power – 2005 Dodge Ram 2500 2005 Diesel Dodge Ram 2500 Customer complaint was severe lack of power and performance on this 05 Dodge Ram 2500 Diesel 5.9 Cummins. Other concern was poor shifting. I took the truck for a test drive as...
Easy tips

Where does the washer go on a bolt head?

Where does the washer go on a bolt head? If you are fastening pieces of lumber together you will want to put washers on both the nut and bolt head sides. Otherwise as was pointed out it generally goes inside of the nut, outside of and against the fastened piece. When do you need to use flat washers? In some cases, the use of the washers is critical to such an extent that not using them could lead to a reduced lifespan of the product being put together. Failure of using them could therefore result in long term destruction of...
Common questions

What does the p0020 code stand for in a car?

What does the p0020 code stand for in a car? A P0020 code refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module) or ECM (engine control module). VVT is a technology used in the engine to allow it to get greater power or efficiency at different running points. What causes an OCV to have a p0020 code? The code can be caused by the OCV having an internal short circuit or an open circuit. The code may be accompanied with code P0021 or P0022. Need help with a P0020...
Easy tips

What should def quality be?

What should def quality be? The ideal, or target reading is 32.5%. If under, more DEF con- centration is needed. If the concentration level is incorrect, either the DEF was of low quality or the tank has become contaminated. The DEF tank should be drained and refilled, only with a known high quality DEF. What is a safe EGT for a 6.7 Cummins? The max for shot bursts is around 1600*, max sustained EGT is about 1250*. As far as boost I am not too familiar with the VGT on the 6.7 but I would say high 30s to low...
Easy tips

What does the new Uconnect update do?

What does the new Uconnect update do? The new system adds tons of new features for future Chrysler, Dodge, Jeep, Ram, and Fiat vehicles, including integrated Alexa support, improved over-the-air firmware updates, and support for wireless Apple CarPlay and Android Auto. Can you update RAM Uconnect? Owners looking to update their Uconnect Systems can do it by requesting a USB drive preloaded with the software, installing it themselves or taking it to a trusted dealership. Upgrading the software yourself takes time, so going to a dealership seems to be the only viable option. How do you reset the Uconnect on...
Most popular

Why did the Check Engine light go on on my Dodge Caravan?

Why did the Check Engine light go on on my Dodge Caravan? I have a dodge grand caravan 2012 and yesterday, the check engine light went on. I know there's usually a way to get the error codes without an OBD device... I was able to do this on my old caravan by turning the ignition on 3 times (without starting the engine). What does p0304 stand for on Dodge Caravan? P0304 is a relatively common trouble code with any vehicle, that includes the Dodge Caravan. It’s and OBD2 code and stands for: P0304: Misfire Detected → Cylinder 4 P0304...
Easy tips

What does fault code p0401 on OBD II mean?

What does fault code p0401 on OBD II mean? What Does Code P0401 Mean? OBD II fault code P0401 is a generic code that is defined as “ EGR Insufficient Flow Detected”, and is set when the PCM (Powertrain Control Module) detects a lower than expected flow of exhaust gas through the EGR (Exhaust Gas Recirculation) system. What does the code p0401 on an EGR mean? Code P0401 is triggered when the EGR temperature sensor does not see enough of a temperature change when the EGR is commanded to open. These sensors tend to get a lot of carbon buildup...