Other

What kind of truck is a 1989 Ford F800?

What kind of truck is a 1989 Ford F800? I looked a very clean 1989 Ford F800 with 12k miles on it in extremely clean condition. The truck has a ford motor and juice brakes. Can anyone help me with this purchase . How many horsepower does a Ford F800 have? There should be a sticker on the valve cover that lists the horsepower rating, if it's intercooled then likely 210 HP otherwise 185HP. Mine is 210HP with going on 450,000 miles on it and it still gets 8 MPG. Hope this helps you out. Want more to check out?...
Common questions

Can a dt466e injector be replaced on a 1999 International?

Can a dt466e injector be replaced on a 1999 International? I have a new truck 1999 International with DT466e. Ebay Injectors look just like the ones we commonly replace ourselves in our 3126E Cat. Wondered if there is a written step by step injector replacement guide for the DT466. Is there a step by step replacement guide for the DT466? Wondered if there is a written step by step injector replacement guide for the DT466. Haven't turned a wrench in this truck yet. She's dumping dark smoke from the tail pipe that smells of heavy diesel. Has skipping idle. Is...
Easy tips

Are pillow block bearings sealed?

Are pillow block bearings sealed? Pillow block bearing units are designed for quick, easy and safe mounting. They are sealed and pre-greased at the factory making them ready-to-use. How do you attach a pillow block bearing? 1) Check and Clean the Shaft. 2) Position the Bearings on the Shaft. 3) Lightly Bolt the Housing to the Mounting Structure. 4) Establish the Final Mounting Position. 5) Securely Bolt the Housing to the Mounting Structure. 6) Ensure the Shaft can Move Axially. 7) Tighten Both Collar Set Screws. 8) Expansion Unit* Do you grease pillow block bearings? Bearings should be greased as...
Other

Where can I get a Timberjack 460 dismantled?

Where can I get a Timberjack 460 dismantled? Equal opportunity lender. Several 460 s being dismantled. Good Running Machine, We are parting out, has a good transmission, good engine, good hydraulic pump, good steering pump, also has 24.5-32 tires and rims. call us for your Timberjack 460 Parts Needs. Enter search information and click the Search button below. How many hours on a 1975 Timberjack skidder? 1975 Timberjack 230 Cable Skidder, 7000 Hours on Engine, Hercules Winch, Tires are 18.4 x 34 It needs a battery Ready for the Woods. The information is the best of our knowledge at the...
Most popular

Why does my Skyjack not charge the batteries?

Why does my Skyjack not charge the batteries? My skyjack 3220 scissorlifts won't charge the batteries. It blinks the 3 lights on charger all the time and beeps. I My skyjack 3220 scissorlifts wont charge the batteries. Is the sjiii 3220 / 26 electric scissor lift optional? SJIII 3220/26 ELECTRIC SCISSOR LIFTS This brochure is for illustrative purpose only and based on the latest information at the time of printing. Skyjack Inc. reserves the right to make changes at any time, without notice, to specifications, standard and optional equipment. How big is an electric scissor deck Skyjack? ■6’ (1.8 m)...
Most popular

How do you reset the code on a 2016 Ford f350?

How do you reset the code on a 2016 Ford f350? Turn the ignition key to the "II" position and wait for the check engine light to go off. This will reset the error codes and the light. How long does it take to reset a PCM? This will take approximately 10 minutes. At any time during this relearn, the light may flash or be on steady. If the ignition switch is turned off at any time during this relearn cycle that the security light is illuminated, the entire cycle must be restarted from the beginning. How can I find...
Common questions

What causes the injector spool to drain on a school bus?

What causes the injector spool to drain on a school bus? 3) Extended oil drains polishing the injector spool valves from wear particles in the oil. The OCI on an engine that BEST fits that vehicle's operating conditions is almost NEVER a simple mileage rule. You NEED to take into account miles, engine hours and fuel use. Why do I have a problem with my fuel injection pump? Fuel injection problems, therefore, are one of the most pressing engine issues to deal with. Whether you’ve experienced fuel injector failure or not, it helps to understand the fuel injector pump, how...
Other

How do you protect inductive loads?

How do you protect inductive loads? One way to protect your power supply from high fly-back voltages when driving inductive loads or loads having stored energy that could be circulated back to the power supply is to use a protective diode network at the output of the power supply. Why is a diode used with inductive loads? When the inductive load is a relay, the flyback diode can noticeably delay the release of the relay by keeping the coil current flowing longer. A resistor in series with the diode will make the circulating current decay faster at the drawback of...
Easy tips

What is the horsepower of a 1010 John Deere?

What is the horsepower of a 1010 John Deere? John Deere 1010John Deere 1010 PowerDrawbar (claimed):30 hp 22.4 kWPTO (claimed):36.13 hp 26.9 kWDrawbar (tested):30.00 hp 22.4 kWPTO (tested):36.13 hp 26.9 kW How much does a 1010 John Deere Dozer weight? John Deere 1010 Crawler DimensionsGas Shiping weight6894 lbs 3127 kgDiesel Shiping weight6999 lbs 3174 kgGauge48 to inches 121 to 0 cm How does a self leveling bucket work? Many loaders have a self-leveling valve for the boom lift and bucket tilt hydraulic circuits. The basic concept is that when you raise the main boom, the bucket is tilted down to...
Common questions

How do I disengage a John Deere parking brake?

How do I disengage a John Deere parking brake? Press the brake pedal down all the way, and THEN press down on the parking brake lever to release it..... The brake lever has a latch that has a hard time releasing if under pressure of pushing down on it. How do you load a non running Bobcat skid steer? 3 Alternatives For Moving A Stuck Skid SteerAttach your high test 20 foot chain to the cage frame of the skid steer. Connect the chain to the front end loader bucket or the track hoe. Use your pry bar, breaking bar...