Why is the 4×4 indicator light not working?
Why is the 4×4 indicator light not working?
This could be a unrelated problem but my driver heated seat also stoped working, the light flashes then turns off but the seat never heats up. Could this be a simple fuse problem or something serious? The 4×4 issue could be the T case shift motor, the transfer case control module, the dash switch, or a fuse controlling any of the above.
How to disable ESC on Dodge Ram 1500?
The ESC does take vehicle speed, throttle, steering angle and vehicle yaw rate into account for correction. On a side note, to disable the ESC, you can pull the F-26 fuse, guys who go off roading do this. It disables the ABS completely so it’s not recommended for driving on regular roads. Click to expand…
What kind of transmission does a Ram 1500 have?
2014 Ram 1500 5.7 8 speed auto transmission with 75,000 miles. I depress brake and turn selector dial to Drive but transmission doesn’t … read more Vocational, Technical or Tra… Dodge Dakota: I have a 2000 Dodge Dakota 4X4 with a 4.7 V8. I I have a 2000 Dodge Dakota 4X4 with a 4.7 V8. I replaced the ignition switch.
Is there an issue with my 2005 Ram?
Intermittent starting issue. 2005 ram 1500. 5.7 hemiXXXXX Go to turn ignition to start and starter just clicks. Sometimes just attempting to start … read more
What are the warning lights on a ram?
The following are warning lights and indicators found in vehicles built by Ram. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are over 70 of them so be patient!
How to fix the gear indicator on a Dodge Ram?
Figure 3. Adjust the gear selector tab. Once the gear selector is adjusted, apply the parking brake, and toggle the shifter through the multiple gears to make sure it has been adjusted properly. If it is working, replace the lower dash panel and its three screws. Then enjoy a properly working gear selector.
What’s the status of the dash gauge on a Dodge Ram?
Here is how you can fix it. This article applies to the Dodge Ram 1500 2nd Generation (1994-2001). The gauges cluster in your dashboard are designed to relay the necessary and vital information for you to be aware of the current situation regarding your truck.
The ESC does take vehicle speed, throttle, steering angle and vehicle yaw rate into account for correction. On a side note, to disable the ESC, you can pull the F-26 fuse, guys who go off roading do this. It disables the ABS completely so it’s not recommended for driving on regular roads. Click to expand…
What to do if your shift selector light is not working?
1. Disconnect the wiring connector from the original transmission mounted PNP switch. 2. Connect the new switch to the wiring connector. 3. Return to Step #4 above and observe the display as you rotate the switch. If all positions indicate properly, refer to the Correction section below.
Where is the shift selector inticator light located?
If not, inspect the serial data circuit, CKT 2470 (Yellow wire), between the TCM and Splice Pack 205. Specifically inspect connector C106, a five terminal connector located below the left side underhood bussed electrical center, directly beneath the red battery cable terminal connection.
When do you turn the 4×4 switch does it light up?
No the switch does not light up at all. The 4X4 and LOW RANGE in the instrument cluster only light up when I start the engine and then go out like all the others. Nothing lights up when I turn the 4×4 switch.
This could be a unrelated problem but my driver heated seat also stoped working, the light flashes then turns off but the seat never heats up. Could this be a simple fuse problem or something serious? The 4×4 issue could be the T case shift motor, the transfer case control module, the dash switch, or a fuse controlling any of the above.
Why are there no lights on the selector switch?
I know this is an old thread but still very informational. On a 99 silverado 5.3 the switch lights would not come on also it was stuck in 2wd.l I replaced the actuator on the transfer case, checked the 4wd fuse in the cab, replaced the switch and the TCCM. Still no lights and no 4wd.
Are there lights on the transfer case selector switch?
Service 4wd and no lights… the lights on the transfer case selector switch in the dash no longer comes on. it does flash when turning the key to start the truck, but it remains in two wheel drive. Ive changed the selector switch, but that did not work.
How often should I switch my 4WD selector?
To avoid having your 4WD selector light come on and go off at random, it’s recommended that you switch your vehicle into 4WD at least once a month and properly maintain your transfer case fluid. When the engine is cool, remove the drain and fill plug at the bottom of your transfer case, which should be facing your rear axle.
