Why is my case 580 K backhoe not working?

Can you send me the part no of the hydraulic oil filter for case 580 K backhoe loader hydraulic not working, on back boom or bucket. I have a 1995 580 super k case backhoe and when u start it it wont go in gear.

Is there a problem with my case 580f tractor?

Hi, A farmer friend of mine has a problem with his hydrolics and hates computors, so im helping him. can anyone explain where he fills up the hydrolic system on a case 580F ?

How big is the controller module on a case 580?

There is an electronic controller module on the pilot controlled machines that manages the functions you listed (stabilizers, ehoe, and aux on some machines). The module is a small box about 3x4x1 inches with a single connector in the middle of it.

What should I do if my case 580K gets stuck?

Got a case 580k every time it gets stuck and tilts hydraulic won’t work on anything. Any solutions when machine is level everything works fine. Fluid is full. I have a Case 580 super M the hdy work good on the back but loader lift is very weak. any help would be great.

Can a case 580b loader pull itself up?

It has shuttle shift. It can barely pull itself up on trailer, sometimes it takes 2 or 3 tries to get it loaded. It won’t push dirt around very well either. If I get in a big hole, it stalls and I have to use the hoe to pull myself out. Loader and backhoe work great, seem to have full power.

Why is my case 580b weak in foward and reverse?

My Case 580B CK, has plenty of power in reverse, but will barely pull it’s self in forward gears. All fluids look good, have been changed and all filters have been changed. Running out of ideas.. any help is appreciated. If after everything else fails. It might be a clogged suction tube inside the gearbox.

What kind of backhoe does a 1967 case 580 need?

1967 Case 580ck Forward Grinding and Will not stay in gear. have a 580 g case backhoe,,,needs frontend 4wd… Case 580D Backhoe has no swing pressure.

Why is my 580K not moving forward or reverse?

My 580 Super K had been running great as I was trying to finish my pond before autumn rains and winter snows made it impossible. As I was approaching a pile of dirt to get a bucket load, it just stopped. No forward, no reverse. No unusual noises. Engine running fine, hydraulics working fine.

When did my 580 Super K tractor stop running?

ALL NEW MEMBERS PLEASE READ THIS FIRST!!! Discussion in ‘ Tractor/Loader/Backhoes ‘ started by rsecrist, Oct 21, 2012 . My 580 Super K had been running great as I was trying to finish my pond before autumn rains and winter snows made it impossible. As I was approaching a pile of dirt to get a bucket load, it just stopped. No forward, no reverse.

Is there a hydraulic problem with my case 580?

Hydraulic problems of the unit. My 78 580 case ck front bucket was working fine, wont go down lever is jammed,goes up and curls down and up is there a release valve stuck making it not go down. any ideas would be great thank you I have a 580e case back hoe.

What’s the name of the new case backhoe?

The new 580 is designated 580K because Case has used the letters F, G, and H on its internationally produced 580 loader/backhoes. (The 580F and 580G

What happens if you forget to disconnect hydraulic hoses?

If you forget to do this step, all the pressure will still be there, and when you disconnect the hydraulic hose, you’ll probably have a blowout of hydraulic fluid.

Can a hydraulic hose be repaired without supervision?

If you’ve never had to repair a hydraulic hose from your piece of heavy equipment, it’s still something you should be able to do, even without any advice or supervision. You can always consult your Owner’s Manual for the recommended steps, or you can simply follow the guidelines listed below.

How to remove hydraulic hoses from an Extendahoe?

(WHOLE GOODS) INCLUDES HYDRAULIC HOS ES, FITTINGS, CLAMPS AND HARDWARE CON TAINED INSIDE OF THE EXTENDIBLE ARM. To remove the boom extension you will have to remove the end cylinder pin and the wear pads so the boom section will slide out. Once the section is out you can remove the cylinder by disconnecting the lines and removing the upper pin.

How do you remove a boom extension from an Extendahoe?

To remove the boom extension you will have to remove the end cylinder pin and the wear pads so the boom section will slide out. Once the section is out you can remove the cylinder by disconnecting the lines and removing the upper pin. Then the cylinder will slide out of the main boom. Reply back if you need further help.

How do you replace a worn out hydraulic hose?

Hydraulic hoses deteriorate over time and could start leaking, and the equipment won’t work properly until you replace worn-out hoses. Start by locating the hose that is damaged. Then remove it by unscrewing it from the equipment. Finally, find a matching replacement hose and install it to get the system going again.

Are there hydraulic hoses inside the extendable arm?

SERIAL NO. (WHOLE GOODS) INCLUDES HYDRAULIC HOS ES, FITTINGS, CLAMPS AND HARDWARE CON TAINED INSIDE OF THE EXTENDABLE ARM. (WHOLE GOODS) INCLUDES HYDRAULIC HO SES, FITTINGS, CLAMPS ANDHARDWARE CO NTAINED INSIDE OF THE EXTENDABLE ARM . PART NO. SERIAL NO.

Why is the diff lock on my backhoe unhooked?

Worked for a company that had about a dozen case backhoes as a mechanic. The diff lock was unhooked when we got a new machine because of this problem after it happened a couple times. The diff lock linkage gets rusted up and once applied will not release breaking the ringgear and pinion. Reply alrmansays: August 17, 2017 at 2:40 pm

Where is the safety switch on a backhoe?

The switch then rests in the middle position for normal backhoe operation, unless the off position is selected by the operator to turn everything off. If you start the vehicle with the switch in the middle position, the safety will not allow backhoe operation until the momentary switch position is pressed.

What was the hydraulic problem on my backhoe?

Case 580 K Hydraulic Problem Jim As I was operating the backhoe today I swung the boom to the left and the engine almost stalled. Then as I started to raise the left outrigger the engine did stall and I couldn’t get it restarted for a long time. Any hydraulic movement lugs the engine down.

How is the transmission on a backhoe controlled?

A: The powershift transmission is controlled by electrics/hydraulics/mechanical drive. – are lights flashing on LED readout? Take note of what they are – they are codes to assist diagnosis Q: My transmission will not go into gear? A: Shuttleshift is also controlled by electric/hydraulic/mechanical drive.

How is the shuttleshift on a backhoe controlled?

A: Shuttleshift is also controlled by electric/hydraulic/mechanical drive. – modulator operation in transmission control valve. Q: The king pin bearings have collapsed & worn the axle housing – Can it be repaired? A: In most instances, YES ! Using the correct procedure ductile iron can be welded.

What causes a backhoe to lock up in reverse?

2) The belville washer in the forward pack breaks into pieces (due to heat or excessive clearances caused by worn plates) – this often causes the forward pack to sometimes lock up permanently, so when reverse is selected the transmission locks up trying to drive in forward & reverse at the same time. Q: I don’t seem to have enough pushing power?

What causes a backhoe to have a clutch problem?

A: Both problems are usually caused by the failure of the forward clutch pack. If the drive is poor in forward it could be that the clutch pack has failed for either 1 of 2 reasons.

Are there any particular problems with case 580 L?

Discussion in ‘ Tractor/Loader/Backhoes ‘ started by ptm600, Oct 8, 2012 . I am looking to buy a case 580 L series backhoe. Am looking for extendahoe, 4 wd, enclosed cab. Are there any particular problems to watch for or years to stay away from? If so, Why? Any advice is appreciated. Thank-you, Paul Case has always made a good loader backhoe.

Where is the grease fitting on a case 580?

The grease fitting for the lower is on the bottom of the knuckle. The grease zerk gets sheared off and packed with dirt if you dont catch it early, the impending doom is costly. The ball joint wears thru the bushing in the axle housing and eggs out the axle housing.

What happens when Extendahoe and outriggers fail?

Extendahoe and outriggers will on occasion fail to operate simultaneously. All other functions of the machine work properly at the time of failure. I’ve crawled all over and mostly under the thing cleaning connections and checking wires. Would someone happen to know if the valves or silenoids are somehow shared by those two functions.

Why is my 580sm series 2 not working?

The machine has me baffled. Extendahoe and outriggers will on occasion fail to operate simultaneously. All other functions of the machine work properly at the time of failure. I’ve crawled all over and mostly under the thing cleaning connections and checking wires.

Why is my case 580 K backhoe not working?