Other

Why does my car make clunking noise when I make a turn?

Why does my car make clunking noise when I make a turn?

Noise: Banging or clunking while making a turn, backing up, or rapid deceleration (like on a freeway off-ramp). Noise gets worse in warmer weather Cause: Posi chatter due to improper lubrication; worn clutches or spider gears; improper assembly Noise:Banging, crunching, or popping while making a turn. Noise not affected by temperature

What causes a low pitch noise when accelerating?

Noise:Howling while accelerating over a small speed range (gears previously quiet) Cause:Worn gear set due to lack of lubrication or overloading Noise:Howling after gear set installation Cause:Faulty gears or improper installation Noise:Low-pitch rumble at all speeds over 20 miles per hour Cause:Worn carrier bearings

What makes a car make a whirling noise when accelerating?

Cause: Loose pinion bearingpreload Noise: Howl with whir or rumble while accelerating at any speed (gears previously quiet) Cause:Worn rear pinion bearing or worn gear set Noise:Howl without whir or rumble while accelerating at any speed (gears previously quiet) Cause:Worn gear set due to lack of lubrication or overloading

What causes a clunk when taking off from a stop?

Noise:Clunk immediately after taking off from a stop Cause: Worn slip yoke splines Noise:Steady vibration that increases with speed Cause:Worn U-joint or out-of-balance driveshaft Noise:Cyclic vibration that varies in intensity. Intensity increases at a specific speed range, worsens during deceleration

Noise: Banging or clunking while making a turn, backing up, or rapid deceleration (like on a freeway off-ramp). Noise gets worse in warmer weather Cause: Posi chatter due to improper lubrication; worn clutches or spider gears; improper assembly Noise:Banging, crunching, or popping while making a turn. Noise not affected by temperature

Why does my car make noise when the temperature is warmer?

Noise gets worse in warmer weather Cause: Posi chatter due to improper lubrication; worn clutches or spider gears; improper assembly Noise:Banging, crunching, or popping while making a turn. Noise not affected by temperature Cause: Badly worn or broken spider gears

What causes a loud clicking noise during acceleration?

Noise: Banging or heavy clicking every two to three feet during acceleration and deceleration Cause: Damaged or broken pinion gear tooth or teeth Noise: Banging or heavy clicking every two to three feet during acceleration or deceleration, but not both

What causes a howling noise in the rear of a car?

Cause:Worn rear pinion bearing or worn gear set Noise:Howl without whir or rumble while accelerating at any speed (gears previously quiet) Cause:Worn gear set due to lack of lubrication or overloading Noise:Howling while accelerating over a small speed range (gears previously quiet) Cause:Worn gear set due to lack of lubrication or overloading

Why does my differential make noise while decelerating?

Sometimes, the noise is not differential-related, but is caused by other driveline or axle components. This guide will help you match up the noise you’re hearing with the differential or axle component making it, or at least get you in the ballpark. Noise: Howl while decelerating (gears previously quiet) Cause: Loose pinion bearingpreload

What does it mean when your car makes a knocking sound?

Engine knocking refers to the metallic sound an engine can produce when pressure is applied to the gas pedal. The noise may be a hollow knocking sound or more of a rattling sound An engine can ping (or knock) due to an improper combustion process.

Why is my lifter making a loud knocking noise?

The noise is camshaft/lifter roller damage caused by the plastic lifter guide worn on one lifter allowing the lifter to ever so slightly rotate causing the roller to dig into the cam lobe and gaulding both surfaces.

Why does my Chevy Silverado make a clicking noise?

I have the same clicking noise on a 2005 with a 5.3. The stethoscope tells me it is inside the oil pan near the back. It is directly related to RPM. Oil pressure is fine and I drive it everyday but the noise is irritating 84 people found this helpful. Guys! Ive had the same problem for quite a while.

Why does my car make a rattling noise when I accelerate?

Knocking Noise when Accelerating The stress on your car while you accelerate can draw out noises you wouldn’t otherwise hear. If your car makes a rattling noise when accelerating, it could be your engine is worn out with low oil pressure or piston slap.

What causes a loud grinding noise when making a turn?

Cause: Posi chatter due to improper lubrication; worn clutches or spider gears; improper assembly Noise:Banging, crunching, or popping while making a turn. Noise not affected by temperature Cause: Badly worn or broken spider gears Noise:Banging or heavy clicking every two to three feet during acceleration and deceleration

Why does my rear differential make a clunking noise?

If the pinion bearings are the problem, they create more of a whirring noise than a rumble because it turns several times faster than the carrier assembly. Regular clunking every few feet can also be an indicator of a broken pinion gear and/or chipped and damaged ring gear.

When does a car make a loud noise?

Unlike engine accessories, a drive or serpentine belt can become loud at engine speeds ranging between 20 and 40 mph. However, a noisy belt can become quiet at engine speeds above 40 mph. 3. Engine Mounts

Why does my Chevy Tahoe make a whining noise when accelerating?

A whining sound when accelerating is almost always caused by a bad accessory attached to your Tahoe’s engine. Here are the most common causes of whining noises when accelerating: 1. Bad Alternator When an alternator is going bad, it’ll often begin to put out a high pitched whining sound. It should also be accompanied by the battery light.

Why does my Chevy Silverado make a popping noise when I Turn Left?

Models: 2014 Chevrolet Silverado 1500 2014 GMC Sierra 1500 Condition/Concern Some customers may comment on a popping noise heard from the front of the vehicle while steering left or right, specifically near the steering gears full left or full right steering position. This condition may be caused by the steering gear shaft dampener rings.

Cause: Posi chatter due to improper lubrication; worn clutches or spider gears; improper assembly Noise:Banging, crunching, or popping while making a turn. Noise not affected by temperature Cause: Badly worn or broken spider gears Noise:Banging or heavy clicking every two to three feet during acceleration and deceleration

Noise:Howling while accelerating over a small speed range (gears previously quiet) Cause:Worn gear set due to lack of lubrication or overloading Noise:Howling after gear set installation Cause:Faulty gears or improper installation Noise:Low-pitch rumble at all speeds over 20 miles per hour Cause:Worn carrier bearings

Why does my Chevy Silverado make a whining noise when I accelerate?

A whining sound when accelerating is almost always caused by a bad accessory attached to your Silverado’s engine. Here are the most common causes of whining noises when accelerating: 1. Bad Alternator. When an alternator is going bad, it’ll often begin to put out a high pitched whining sound.

What’s the problem with my Suburban 1500 whining?

My 05 Suburban 1500 has just started whining & does it with the revs in gear. First & second gear seem worse than the others & the wife said the fluid was very low, it only took 2 quarts though. I was thinking torque converter or oil pump in trans.

Where does the lifter sound come from on a Chevy Silverado?

You can hear lifter click best around the top of the engine, and isolate the noise with a stethoscope against the valve cover. It will occur at idle and increases as you rev the engine, continuing even when the engine is warm. Valve lifter noise is detrimental and should be addressed quickly.

Is there a problem with my GM suburban?

Well, i looked on google and read about it for the pass 5 hours and cant find a similar problem. i have a 2006 suburban 1500. 293,xxx KM. Everything goes good no check engine , shift good , drive good BUT… When i drive around i have that whining sound only when im in drive and i press the gas pedal.

Why does my Chevy Tahoe make a clunk sound?

After that I had this clunk sound from the rear end and I swore it was my rear diff. The chase began, rear end serviced and carrier bearings replaced…no fix. One tech thought to be leaf spring bushings (the where basicly gone)…no fix.

What should I do about my Chevy Tahoe drive line clunk?

The chase began, rear end serviced and carrier bearings replaced…no fix. One tech thought to be leaf spring bushings (the where basicly gone)…no fix. New slip yoke and u-joints…no fix. I had another tech swear it was the rear diff, I just couldn’t throw $500 towards something I really felt was not the problem…didn’t do it.

What causes a clunking noise on the driveline?

Cause: Bad wheel bearings Noise: Driveline squeaking or grinding at any speed Cause:Worn or damaged U-joints Noise: Clunking when depressing the throttle pedal (takeoff) Cause:Worn U-joints; worn spider gears; worn axle splines; excessive gear backlash; loose yoke splines; worn slip yoke splines Noise:Clunk immediately after taking off from a stop

What causes a clunk when depressing the throttle pedal?

Noise: Clunking when depressing the throttle pedal (takeoff) Cause:Worn U-joints; worn spider gears; worn axle splines; excessive gear backlash; loose yoke splines; worn slip yoke splines Noise:Clunk immediately after taking off from a stop Cause: Worn slip yoke splines Noise:Steady vibration that increases with speed

What causes low pitch rumble at 20 miles per hour?

Cause:Faulty gears or improper installation Noise:Low-pitch rumble at all speeds over 20 miles per hour Cause:Worn carrier bearings Noise:Whirring during acceleration/deceleration at about 10 miles per hour Cause: Worn pinion bearings See Also: Ask Away! with Jeff Smith: How to Fix Driveline Vibrations by Adjusting Pinion Angle

Why does my truck make a clicking sound when I turn it off?

The sound lasts for about 10 seconds and then stops. When I turn the truck off, it happens again for about 10 seconds. The problem didn’t occur often until I had the AC system recharged lately. What do you think the problem is? If I need to replace the blower motor, how can I remove the plasting cowling in front of it without cutting it out?

Why does my truck make a grinding noise?

Clancy, tried your suggestion this afternoon and the truck does not buck or shudder, just the normal 4WD feeling when the front is locked with the rear. Stumpuller6.5 Shits gonna get Abrasive…

Cause:Worn rear pinion bearing or worn gear set Noise:Howl without whir or rumble while accelerating at any speed (gears previously quiet) Cause:Worn gear set due to lack of lubrication or overloading Noise:Howling while accelerating over a small speed range (gears previously quiet) Cause:Worn gear set due to lack of lubrication or overloading

What kind of noise does front suspension make?

Noise in front suspension ( 05′ z71 ) when turning wheel to the left. Major Vibration?!?!

Why does my GM Truck make a popping noise?

X2.. This is a bad CV joint causing your clicking & popping Jordan. Check it & see if it’s dry. You may just need to pump a little grease into the boot & squeeze it into the joint to stop it if it isn’t too far gone. The fact that the noise is worse on a tight turn just solidifies the outer CV joint as being the problem.

Why does my transfer case make a grinding noise?

Transfer Case grinding noise – FIXED! Discussion in ‘ Mechanic’s Corner ‘ started by stadt11, May 23, 2010 . My transfer case has started making a horrible grinding noise. First I thought it was coming from the driveshaft or the front/rear diff, but wasn’t sure.

Is it normal to make noise when accelerating?

There are noises that are normal on acceleration. The best way to know if the noise is normal is simply if you have heard the noise before. You have probably driven, or at least ridden in cars for years.

What causes heavy clicking noise during acceleration and deceleration?

Noise: Banging or heavy clicking every two to three feet during acceleration or deceleration, but not both Cause: High spot or heavy chip on pinion gear tooth Noise: Banging or heavy clicking every eight feet during acceleration and deceleration Cause: Damaged or broken ring gear tooth…

What causes knocking sound when accelerating?

Again, the noise is more noticeable on acceleration because the engine spins faster. The pistons can also wear and make noise. The pistons are what move up and down and make the engine spin. Worn pistons will make a knocking noise — sometimes at idle, and often on acceleration.

Why is my car making clunking sounds when I turn?

7 Common Things to Look For When You Hear a Clunk Worn or bad tie rods. Bad or worn out tie rod ends will cause a knocking sound as you turn the wheel. Damaged sway bar links or anti-roll bars. The sway bar links are designed to keep all four tires from leaving the ground as you turn aggressively. Bad suspension bushings. Broken ball joints. Worn out shock absorbers or struts. Broken CV joints.

What causes a grinding sound when accelerating?

However, worn out wheel bearings can lead to friction, causing grinding noise while turning the car on bends. This noise persists when the car is accelerating. Replacing the wheel bearings should stop the noise.

Why is my car making a whining noise when accelerating?

Why is Your Car Making Whining Noise When Accelerating? Transmission Problems. One of the major causes of whining noise can be the friction in the car transmission during acceleration. Faulty Steering. Engine Problems. The Power Steering Problem. The Clutch Components. Normal Resonance. The Torque Converter. Gear Problems. You Treat Your Car Like Shit. Examine Transmission.

Noise: Clunking when depressing the throttle pedal (takeoff) Cause:Worn U-joints; worn spider gears; worn axle splines; excessive gear backlash; loose yoke splines; worn slip yoke splines Noise:Clunk immediately after taking off from a stop Cause: Worn slip yoke splines Noise:Steady vibration that increases with speed

Noise:Clunk immediately after taking off from a stop Cause: Worn slip yoke splines Noise:Steady vibration that increases with speed Cause:Worn U-joint or out-of-balance driveshaft Noise:Cyclic vibration that varies in intensity. Intensity increases at a specific speed range, worsens during deceleration

What makes a cv shaft make a clicking noise?

Loud clicking noises when turning or accelerating. When CV axles become excessively worn, the constant velocity joints will become loose and click when turning or accelerating. The clicks may become louder or more pronounced during sharper and faster turns and will be heard on the side with the faulty CV shaft.

Sometimes, the noise is not differential-related, but is caused by other driveline or axle components. This guide will help you match up the noise you’re hearing with the differential or axle component making it, or at least get you in the ballpark. Noise: Howl while decelerating (gears previously quiet) Cause: Loose pinion bearingpreload

Noise: Banging or heavy clicking every two to three feet during acceleration and deceleration Cause: Damaged or broken pinion gear tooth or teeth Noise: Banging or heavy clicking every two to three feet during acceleration or deceleration, but not both

Why does my Dodge Ram make a clunking noise?

When turning right or left slow speed and starting up a grade i have a clunking noise in my front end. Took to service they said everything tight and working just getting annoying. I can hear it especially when the suspension flexes like over a speed bump or the bump i go over to get into driveway

Where does the clunk come from on a Dodge Ram?

Im not sure if yours is the same, but many people are having a problem with a clunk when their suspension rebounds aburptly. The clunk is felt and heard around the floorboard area of the driver and/or passenger sides. bri6679 likes this.

Why does my Ford Edge make a clunking noise?

While these noises may be a symptom of some different issues, all are usually related to a suspension component that has failed. When a suspension component has failed, the ride or the vehicle may be altered. If the failed component is not dealt with, it can lead to increasingly difficult and dangerous problems.

Why does my Ford Mustang make a pop sound?

It will also keep somewhat of a vacuum inside so that when you pull the driveshaft all the way out, it will make a small “pop” sound. No, your driveshaft is not going to slide all the way out driving down the road or even jumping it. “It’s a noise in the rear end” – No, it’s not.

Why does my Chevy Equinox make a clunking noise?

Depending on the vehicle, one or two ball joints per wheel and may or may not be load bearing. If a ball joint is beginning to fail, you may notice a clunking noise coming from the front wheels. This clunking noise will become louder and more frequent over time.

What makes a car make a clunking noise when going over bumps?

Sway bars can help keep a vehicle from rolling over when going around a sharp corner. If the sway bar breaks or is damaged it may produce a clunking or knocking sound, especially when going over bumps. Your vehicle may also had more difficulty handling when the sway bar is damaged.

What’s the noise coming from the front tire?

Q: Rubbing noise coming from the front driver’s side tire. What could be the problem? When driving I keep hearing a sort of soft scrubbing noise coming from the driver’s side front tire.

What makes a wheel hub make a clicking noise?

If it doesn’t, you may have a bad wheel bearing. Here are a few other sounds and symptoms of bad wheel hub bearings: Snapping or clicking noises. This is sometimes also caused by a damaged CV joint, but can also be due to worn wheel bearings if you hear a clicking noise when turning. Humming or growling noises.

Why does my car make noise when I go over 20 mph?

If you hear the noise above 20 mph it’s most likely a wheel bearing noise but it’s not a bad idea to check the tire tread to be sure the tires are not chopped or worn uneven. If you what to leave me more details about the noise I may have a more definitive answer to what may be the problem.


Author Image
Ruth Doyle