Why does my AC blower motor not work?

The blower motor relay supplies power to this motor when you turn the switch to “on” that can sometimes fail. When this happens, you may notice that you will not feel anything blowing out of the vents at all. This may also cause the blower motor to work intermittently.

Is there a problem with the GM blower motor?

If you have a General Motors car or truck from 2002 through 2008 you’ll probably have a blower motor issue at some point. In many cases it’s a problem with the GM blower motor module. The most common complaint when this part fails is the motor will not turn on at all.

What happens when a blower motor resistor fails?

The blower motor resistor is the component directly responsible for controlling the blower motor fan speed. If the resistor shorts or fails, it may cause the blower motor to remain stuck on one fan speed.

Can a blower motor be replaced in an AC evaporator?

The blower motor module is close to being the lowest point and will wind up sitting in a bath of water. If you replace this part go the extra step and make sure that the condensation drain is clear on your AC evaporator. Also make sure your old blower motor spins freely and isn’t starting to bind.

How can I tell if my blower motor is working?

If the blower motor works it’s time to check some voltages at the module. There’s a power wire that comes from the control panel. On most models it’s either red or purple. This power in wire should turn on a test light with the ignition on and maximum speed selected. The black wire should indicate a strong ground.

How does the speed of a blower motor work?

This means that the current running through the blower motor, and its’ speed is therefore controlled by the resistor value. The user chooses a fan speed by selecting a speed which then connects one of the resistors in the blower resistor pack.

What to do if your blower fan is not working?

Blower Motor Resistor Replacement – YouTube Blower fan not working – 2004-2014 Ford F-150 and other models. Blower Motor Resistor Replacement If playback doesn’t begin shortly, try restarting your device.

What to do if your AC or heater is not blowing?

If your Blower Motor for the AC or Heater suddenly stopped blowing, look here first, it might save you several dollars. Situation, we have a friend that owns a 2017 Chevy Trax LT, she is a nurse who works with my wife, single mom and on a single mom budget.

Why is the resistor not working on my blower?

Hi There, The resistor is what controls the speed of the blower motor, not the relay. The blower motor relay supplies power to this motor when you turn the switch to “on” that can sometimes fail. When this happens, you may notice that you will not feel anything blowing out of the vents at all.

What to do if your AC blower is not working?

Disconnect cables to motor and resistor. Remove hose from motor, it should just pull off with little effort. Unscrew motor and resistor. Screw new motor and resistor in. Connect hose to motor. Connect cables to motor and resistor. Turn on car and test AC. Thanks for watching! Loading…

What causes a blower motor to stop working?

In a situation where the motor doesn’t work on any speed, the most likely causes are: a blown power supply fuse, a bad motor ground connection, bad motor speed control module or a failed motor. On all systems, a failed blower motor is least likely. Blower motors generally don’t fail out of the clear blue.

How to fix a Chevy Express heat fan blower?

– Resistor Replacement, Wire Harness Repair – YouTube Chevy Express Van- Ac/Heat Fan Blower issue Fixed! – Resistor Replacement, Wire Harness Repair If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.

Why is there no power to my AC compressor?

No 12 volts at comp plug. Went to heater control panel, have 12 V at ac switch, (with blower on) and so switch is sending it down the line but where it goes to, I don’t know. Can’t find any fuse or breaker labelled AC.

What to do if your blower is not working?

The very first step you need to take is getting a scan run on the computer. Take your car to a technician or a local parts store and have them scan the car. They will give you a list of… Hello there, thank you for asking about your 1998 Oldsmobile LSS.

What causes a blower fan to turn faster?

The lower the resistance of the selected resistor in the pack, the higher the current that flows through the blower fan causing the fan to turn faster. The statements expressed above are only for informational purposes and should be independently verified.

Why does my Astro AC fan not work?

My 91 Chevy Astro doesn’t like to blow air on high. The AC/Heater fan works fine at lower settings but when in high it doesn’t work at all or will run for 30 seconds and then stop. I’ve replaced the switch in the dash, but that didn’t help.

Why is my AC heater fan not working?

This sounds more like a problem with high speed fan relay. On the low speeds, the fan relay routes the voltage thru the resistor block. When you switch to high fan speed, the relay switches over to supply full voltage from the battery to the fan motor.

Why does my heater not work on high speed?

Heater blower motor will not work on high speed? I have replaced the black bosch relay behind the glovebox, the blower resistor and the blower motor and still cannot get the blower to work on high. I remember in older model years of gmc’s and chevys that their was a high speed blower relay that caused this issue.

What happens if heater blower motor does not work?

Therefore, if major problems in the heating and air conditioning system fail, as if the power supply to the motor was completely cut off due to overheating or corrosion, the motor will simply not work, which in turn will render the entire heating and air conditioning system unusable, as no air will flow through the vehicle’s air vents. 2.

How to replace a blower motor on an AC fan?

REPLACE THE BLOWER MOTOR RESISTOR AND RESISTOR MODULE CONNECTOR. Replace the blower motor resistor and module connector using the following procedure: Remove the blower fuse. Lower the hush panel or close-out panel enough to gain access to the resistor module connector. Disconnect the connector from the resistor module.

Why is my F150 heater fan not working?

When a Blower Resistor fails it can fail in many ways. 1 being the fan won’t turn off unless you pull a fuse 2. you may only have one speed as i suffered high or nothing. 3. you have may not have any fan at all. while there is many reasons for this to fail which includes high resistance in the blower motor. Loading…

Why does my blower motor only work at slow speed?

Blower motor only working on low speed. Another common symptom of a faulty blower motor resistor is that the blower motor only works at slow-speed. This can be caused because of bad wiring between the blower motor resistor and the blower motor itself.

How to choose the right air conditioner blower motor?

In order to get the right blower motor for your air-conditioner, the contractor has to take a number of things into consideration, including the type of drive, the diameter of the motor, rotation direction, horsepower, voltage, speeds, and size of the capacitor.

What causes an air conditioner fan to fail?

A dirty blower motor fan can cause the blower motor to fail and cause ice build up. If this is your issue, then the solution, in most cases, is not too difficult in most cases and simply requires you to open up the air conditioner unit, remove the fan from the blower motor assembly and thoroughly clean it, in warm soapy water if possible.

Why does my HVAC blower need to be replaced?

The blower motor is the part of your HVAC system that uses the most energy, so it may very well be the culprit if you see a significant rise in your utility bills. An aging, problematic, or dirty motor has to work harder to properly circulate conditioned air throughout your home, which leads to higher energy consumption.

What happens when a blower motor relay wears out?

Without it, the AC system will not be able to circulate any heated or cooled air. The blower motor relay controls the current used to power the blower motor, and is subject to the constant on and off switching. Over time, it can eventually wear out.

What are the symptoms of a worn out blower motor?

One of the symptoms of a worn out blower motor is that it can intermittently produce a loud screeching noise when running. How to test a blower motor? If the blower motor doesn’t work at all, the blower motor itself must be tested first. Typically it’s done by measuring the voltage at the blower motor connector when it’s turned on.

What to do if your car AC is not blowing?

Depending on what kind of car you have, it should be a pretty simple fix. The problem sounds like it is with your blower motor, not your AC system. Hopefully, the blower motor simply blew a fuse. Find your fuse panel and check the fuse for the “blower motor” or “vent fan” or something like that.

When does the rear AC blower turn on?

Three years ago I replaced the rear blower motor control module, which caused the rear AC to start working again. That was no fun with such a tight space to try to loosen and tighten nuts in! Since then there has always been, however, an approximate three minute delay for the rear AC blower to turn on.

Why is my a / C blower not blowing?

A metal that when it corrodes, it turns white, and unlike copper, aluminum corrosion does not conduct electricity at all and causes resistance issues and can cause overheating of a circuit. Took out a common finger nail Emory board and went to work, both sides of each contact, then used a small brass brush on each side and along the tips.

Why is my rear AC not turning off?

Today I disconnected both the front seat (near the shifter) and first rear seat controls for the rear AC. It didn’t change anything. I finally removed the fuse under the first rear seat to get it to stop blowing. Less than a year ago I replaced the front blower motor control module because the front speeds weren’t working right.

Why does my Dodge Ram fan only blow on high?

This feature is not available right now. Please try again later. If your Dodge’s heater or AC fan will only blow on high, or if it intermittently works on low but then stops, it is very likely your heater resistor. A cheap, easy to replace part, that anyone can fix. Loading…

What are the signs of a bad heater motor?

Common signs include the car’s heater not working or getting stuck on a certain speed, or something getting jammed in the blower motor. 1. Blower motor stuck on one speed 2. Blower motor does not work on certain settings 3. No air from the vehicle’s vents Average rating from 130,908 customers who received a Vehicle Engine Cooling Inspection.

How does a high speed blower motor work?

In the highest fan speed state, the blower resistor is bypassed completely and the fan is effectively connected directly to the car’s battery, allowing maximum current to be supplied to the blower motor.

Where do I replace the resistor on my blower motor?

To repair the problem, simply replace the resistor block. It’s usually located in the ductwork (to keep the coils cool) below the glove box. Unplug the electrical connector, remove the screws and replace the unit. Replacement blower motor resistor blocks are usually available from any auto parts store or the dealer.

What to do if your blower motor only works on high speed?

If your blower only operates on its highest speed, chances are you have the series type of blower motor resistor. This is the most common failure mode. To repair the problem, simply replace the resistor block. It’s usually located in the ductwork (to keep the coils cool) below the glove box.

When do you need to replace the blower motor relay?

If the blower motor does not function, car fuses are blown, or relays are melting, you may have to replace the car blower motor relay. 1. Blower motor does not function 2. Blown fuses 3. Melted relay The blower motor relay is the electrical switch that is used to supply the power for the vehicle’s blower motor.

Where is the blower control switch on the dashboard?

The blower control switch on the dashboard controls the circuit flow of the blower motor to adjust the voltage from low, to medium, to medium-high, to high. When on high, the circuit bypasses the blower resistor.

When did the Dodge Dakota first come out?

From its introduction in 1986 to 2009, it was marketed by Dodge division and from 2009 it has been marketed by the newly formed Ram division. It has a conventional design with body on frame construction and a leaf spring/ live axle rear end. Get notified for new files?

What does a HVAC blower motor do in a house?

What is an HVAC Blower Motor? The HVAC blower motor is the heating and cooling systems component that sends conditioned air from the furnace, heat pump, or air conditioner into the home. Once the system heats or cools the air, the blower motor forces it through the duct system and out the vents in rooms throughout the house.

What should I do if my blower fan wont come on?

You will need to test with a voltmeter and see if your fan motor is getting the required 110 to 125 volts AC out of your control board to start the motor. I would suggest setting your thermostat to the “Fan ON” position. You should be getting 120 volts out of the control board.

Why is my furnace blower motor not working?

Another common problem with furnace blower motors not working is caused by the “three D’s”; dust, dirt and debris. These three alone can cause overheating of the motor, which in turn causes the windings and bearings to burn up quicker. Dirt, dust and debris can cause the blower motor to overheat and seize up.

Why is my AC heater not working?

The potential issues here vary whether your heating has gone out or your car’s AC system is on the fritz. Common reasons for the heating system not to work include the following: Low coolant. Air in the coolant system. Malfunctioning heater core. Failed (or failing) thermostat.

How to tell if your furnace blower motor is overheating?

Your blower motor may show these signs when it starts to overheat: A hot or burning smell as your units operate. It is usually followed by the complete furnace shut off. Loud humming noise and other odd sounds. These can be caused by anything that hinders the blower motor from operating. Furnace cycles off or refuses to start. This may require you to ‘reset’ the furnace before it operates.

What causes the AC blower not to come on?

A common problem behind an air conditioner blower not starting includes overheating, which keeps the motor from running. Let your air conditioner rest and cool down for a while before trying to turn it on again; if the motor works at that point, overheating is probably the problem.

Can a blower fan work only when the thermostat is set to fan on?

Fan will work only when thermostat set to fan on. Thank you for the question, Anon, as it’s a common A/C, or heating fan operating problem that needs to be understood: I put it as “The blower fan runs only in the MAN-ON switch but won’t run on AUTO”.

What to do if heater blower won’t run?

If you have a 108, 109, 114 or 115 chassis you will have to remove the center console and dash to get to the motor. If you have a 107, 116, 123 or 126 Chassis access to the motor is quick. For the 201 and 124 chassis it takes a little more work as you have to remove the wiper and intake air vent assembly.

What to do if your central air blower won’t work?

If the thermostat, breakers and access panel doors check out, the blower motor itself may have failed. Motors have a long useful life, but they do seize up or burn out in time. You may want to call a repair person at this point. A qualified air conditioning expert can test the motor, find the proper replacement and install it.

When do you need a new blower motor?

If you are getting 120 volts to the motor and it is not starting then you have a blower motor problem and either need another new blower motor or a new blower motor run capacitor. If you are not getting voltage to the blower motor out of the control board then you probably need a new control board again.

What would cause the furnace blower not to turn on?

1 – Low airflow Dirty Air Filters. If you don’t change your air filters often enough, the filters will become dirty and clogged, which means the heat exchanger retains heat and eventually causes it Dirty Blower Wheel. If your furnace goes on and off too quickly, it could be a dirty blower wheel. Closed or Blocked Air Supply Vents.

Why does my Ricks free auto blower motor not work?

A clogged cabin air filter reduces airflow through the ducts, increases current draw on the blower motor and can cause blower motor resistor overheating and premature failure. If you replace the resistor and it burns out again, check the current draw on the blower motor.

Why is car AC not blowing cold air after recharge?

So, whenever your Car AC not blowing cold air after recharge, follow the above tips. Or, you can simply take your vehicle to the professionals as they know what exactly to do. Moreover, timely repair can avoid future issues as well. u001dIs it safe to charge the phone when the car is off?

What causes a bad or failing blower motor relay?

Blown fuses. One of the first symptoms of a bad or failing AC blower motor relay is a blown AC blower motor relay circuit fuse. If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current…

What are common reasons my GMC Jimmy heater is not working?

What are common reasons my GMC Jimmy has heater problems? While there are a variety of reasons your GMC Jimmy heater is not working, the most common 3 are a broken heater blower motor, a problem with the thermostat, or a failed heater blower motor resistor. See what others are asking about their GMC Jimmy.

What happens when the blower fails on a Chevy Equinox?

When the blower motor fails, the air conditioner and heater may still work, and heat or cool may be felt at the vents, but the air pressure will be dramatically decreased. This Read More When the heater control valve fails, adjusting the temperature may not change the air temperature at the vents, whether hot or cold.

Why is no air coming out of my dash vents?

I can only get air to blow out of the defroster vents or the floor vents, no matter if i use heat or A/C. I have heard some people say it is probably a vaccum hose issue.

What happens if the heater control valve fails?

When the heater control valve fails, adjusting the temperature may not change the air temperature at the vents, whether hot or cold. Also, the valve could leak engine coolant, p…

Why does my AC quit working on my Ford E-450?

Normal operation. When the load or the throttle position reaches a predetermined point the AC compressor will automatically shut off until the load or the throttle backs off then it will kick back in. 5 people found this helpful. So, I’ve also had this problem in an E-450 can on my class C motor home. Took it to Ford.

Where are the resistors on a Ford blower motor?

The Ford blower motor resistor assembly, covered by this tutorial, has 3 different resistors in series. The purpose of these resistors is to reduce the amount of the blower motor’s current that’s passing through them (as you’re probably already aware, these resistors are located between the blower motor and ground).

How much does a blower motor cost on a Ford PowerStroke?

It looks like a blower motor is about $35 from the local parts place, but you have to swap the plastic fan which is probably easier said than done (I picture myself prying on it and destroying it).

Why does my Ford PowerStroke blower quit working?

Well the “NEW” blower motor is as weak, or weaker, than the original 13 year old Ford blower. That isn’t the problem. It’s been on the truck for 1 day and it’s going back to RockAuto. Today in the 90 degree heat, it decided to just quit spitting anything out of the vents altogether.

It looks like a blower motor is about $35 from the local parts place, but you have to swap the plastic fan which is probably easier said than done (I picture myself prying on it and destroying it).

When to test the blower motor resistor in a Ford?

If the blower motor in your Ford vehicle only works in one speed (usually just high), then there’s a good chance that the blower motor resistor is bad and behind the problem. Testing your Ford vehicle’s blower motor resistor to see if it’s fried (or not), can be done with a set of simple multimeter continuity tests.

What makes a blower motor turn slower than full speed?

The purpose of these resistors is to reduce the amount of the blower motor’s current that’s passing through them (as you’re probably already aware, these resistors are located between the blower motor and ground). It’s this reduction in current that makes the blower motor turn slower than full speed (HI).

What to do if your blower won’t work?

Head under the hood and check the blower motor wiring to make sure it is getting power to it. If it is, then your only option is to remove the blower motor and have it tested or replaced. You can do so yourself if you have the equipment, or have it done at the dealership or parts store.

Why is my a / C heater fan not working?

Hey Guys I need some help. The blower fan in my A/C ( or heater) does not blow. On the display it says its on. The Auto feature trys to adjust the blower fan speed to the proper speed but nothing happens! Basically everything works but the blower. Also this is a intermitten problem.

Why is my blower fan not blowing air?

The blower fan resistor is a simple electronic circuit that changes the resistance of the current sent to the blower motor, and enables multiple fan speeds. If you find the blower fan works, but only at a single speed setting, the blower motor resistor has probably gone bad.

Why is the blower motor not working on my Ford F150?

During a road trip with the air conditioning operating continuously for many hours, the blower motor stopped functioning. The black/white wire to the blower speed controller was warm to the touch and when wiggled, the blower motor restarted. Operation of the blower motor worsened during the remainder of the trip.

Why is my blower not working on my Chevy Silverado?

Another common problem will be the blower motor will stick in the ON position and never shut off. You can access the resistor module behind the fuse box located on the driver’s side lower dash compartment. You must visually inspect the resistor, and make sure it isn’t melted or burnt. If it is, then replace it.

How many fuses are in a Ford E150?

Fuses and relay Ford E150 E250 E350 1988-1993 Fuse number Amps Circuits Protected 1 15 Stop Lamps, Hazard Flasher, Speed Contro 2 7.5 Windshield Washer/Wiper, Intermittent Wi 3 Not Used 4 15 Instrument Panel Illumination, Running L

How is the speed of the blower motor controlled?

The blower resistor is connected in series to the blower fan motor. This means that the current running through the blower motor, and its’ speed is therefore controlled by the resistor value. The user chooses a fan speed by selecting a speed which then connects one of the resistors in the blower resistor pack.

What causes a fuse to blow on a blower motor?

If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current from a bad relay will blow the fuse and cut power in order to protect the system.

What happens if you have a bad blower motor?

The blower motor is the component responsible for pushing air through the vents of your vehicle’s heating and air conditioning systems. Without it, the AC system will not be able to circulate any heated or cooled air.

Can a Hyundai blower motor need to be replaced?

The insulator panel will need to be removed to check this. If the connection is good check the relay. If everything is in order the blower motor might need to be replaced because it could have an internal problem like the brushes or bearings could be worn.

What should I do if my blower motor is not working?

The blower motor is crucial to the proper functioning of your HVAC system. This video will show you how to properly diagnose your blower by using the multimeter to perform an AMP draw as well as replacing the blower motor relay. Loading…

Why is my front AC blower not working?

I’ve seen many posts from people whose front AC blower would stop occasionally. My wife would kick the wires under the glove compartment and it would start again. It finally failed altogether. Following the advice from other owners, I replaced the blower motor resistor. That didn’t help.

How does a 3 speed blower motor work?

Older style blower motor resistor with exposed resistor elements. The blower motor resistor is what’s responsible for giving you three blower speeds. The resistor block contains three different high resistance coils. Think of these coils like a filament in a light bulb.

What happens when the resistor on a blower motor fails?

The coil resistance causes them to heat up, thereby reducing the amount of voltage that can flow to the blower motor. When a resistor coil burns out, you lose that fan speed. A blower motor resistor can fail in several ways; since many are designed in series, if one resistor fails, you loose speeds 1-3.

Why does my AC blower motor not work?