Where do I find the trouble code on my Pontiac?

These are listed in numerical order for easy searching. When retrieving Pontiac trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.

What do you need to know about the wiring on a Pontiac?

These Pontiac Wiring information / Aftermarket Autostart/Alarm Technical Wiring Diagrams are very useful, if not required, for the installation of alarms, autostart / alarms, remote starts, doorlock info and any other aftermarket installation that would require you to know the / Wire Information / Wiring Information of your Pontiac

What does the P0300 Pontiac engine control module mean?

P0300 PONTIAC Meaning The Engine Control Module (ECM) uses information from the crankshaft position sensor and the camshaft position sensor to determine when an engine cylinder misfire is occurring. By monitoring variations in the crankshaft rotation speed for each cylinder, the ECM can detect individual cylinder misfire events.

Are there any free schematics for Pontiac cars?

Please select your desired model below. We have 14 Pontiac Vehicles Diagrams, Schematics or Service Manuals to choose from, all free to download! Brand names and product names are the property of their respective owners.

When did the Pontiac Trans Sport get its name?

For the 1998 model year, Pontiac renamed the Trans Sport the Pontiac Montana, deriving the name from an exterior trim package introduced for 1997; the Montana was sold in two generations through 2009 (2006 in the United States).

When did the power sliding door come out on the Pontiac Trans Sport?

The power sliding door became available as an option, after being introduced in 1993. Built-in child seats for the second row became available as an option. A traction control system became available as an option with the 3.8L V6. Rear deep-tinted windows now featured a darker tint than previously used.

When did the Pontiac Trans Sport Montana come out?

For the 1997 and 1998 model year (1999 in Canada), along with the roll out of this new generation of minivans, the Pontiac (Trans Sport) Montana was debuted, which had special cladding and wheels intended to give it a more rugged SUV-like appearance.

How many seats does a Pontiac Trans Sport have?

The Trans Sport had three seating options: five-seat (three removable bucket seats in the second row); seven-seat (adding two removable bucket seats in a third row) and six-seat configuration, with two bucket seats per row. Air suspension was offered as an option.

How to read GM OBD diagnostic codes for free?

How to read the codes 1 Ground terminals A and B (see diagram below) with the ignition “ON” and engine not running. The system will enter the… 2 After Code 12 is displayed, any stored trouble codes will be displayed by flashing the “CHECK ENGINE”, “SERVICE… More …

What is the W124 diagnostic trouble code ( DTC )?

Pin #14 – CC/ISC (Cruise Control / Idle Speed Control) – For models without ASR traction control (WIS Group 30.21, subgroup 7.3, section 11, two pages) Pin #14 – EA/CC/ISC (Electronic Accelerator / CC / ISC) – For models with ASR traction control (WIS Group 30.20, subgroup 6.4, section 11, two pages)

What are the GM trouble codes for 2008?

Here is what I have done since Aug. 2008 I have replaced the MAF sensor, air filter, knock sensor, fuel pump, coil, tps, fuel filter, distributor cap and rotor. But guess what I am still having the same codes in this order P0327,P0171, and P0174.

What are the trouble codes for a 2000 Jeep?

2000 jeep limited 4.7 4×4…..just put in new timing chains and everything else in there is new also. Jeep ran fine before new stuff was put in and it does start good now but its running rough and showing codes now. It almost sounds as if there is a vacuum leak now since I can hear a sucking kind of…

Where is the DLC on a GM 94?

Locate Data Link Connector (DLC), see image below. Turn Ignition switch to ON position. Count the flashes on the “ CHECK ENGINE ” or “ SERVICE ENGINE ” light. NOTE: Some 94 & 95 models do not have the B terminal. In which case a scanner is required.