Other

When does the brake light come on the turn signal comes on?

When does the brake light come on the turn signal comes on?

when the brake is pushed in both the front and rear turn signal lights come on and stay solid even when the turn signal is on and they are on the passenger side only. Also when the turn signal is on for a right hand turn the brake light on the top of the cab blinks too.

When is the turn signal on for a right hand turn?

Also when the turn signal is on for a right hand turn the brake light on the top of the cab blinks too. When the hazard lights are on both the turn signal and brake lights flash on both sides. Thanks for your help but I think my truck is possessed That just confirms what i have been saying about the short between the brake and signal.

Why are my turn signal lights not working?

Check for damaged or burned-out bulbs in all turn signals on that side. Alternately, the ground on either light could have gotten damaged or come loose. Corrosion in one of the bulb sockets causing bad contacts is another possible cause.

How can I diagnose a turn signal problem?

Diagnose Turn Signal Problems. The flasher contains what’s known as a “bi-metallic spring,” which is a flat strip with one kind of metal on one side, and another kind on the other. The flexible strip connects the electrical supply from the box to the wiring that goes to your turn signal switch.

Where is the turn signal on a GM Truck?

It is located on the frame crossmember above the spare tire. It was corroded and the clip was weak. I cleaned it up, put some electronics grease on it and put it back together. Then I used zip ties to hold the connector together. I never had an issue after that.

Why is my turn signal not working on my truck?

They found: “No power coming out of BCM for turn signal-tested-found circuit 1334 yellow & black wire shorted to ground-found short located in underhood fuse block-replaced underhood fuse block.” My cost for repair: $600.

Why does my brake light work when I Turn on the turn signal?

For that to work, the brake wire runs to the turn indicator, so that when you turn on the flashing turn signal, it switches out the brake light signal for that side so that the two signals don’t collide. So don’t just check the brake light. Also check the turn signals.

Why does my turn signal blink twice as fast as the front?

I haven’t even begun to check it out, except for glancing at a reflection of my left turn signals as I’m driving. It appears that the front is working and the back is not. It blinks normal speed on the right side, but twice as fast on the left. Is this because the rear light appears to be out, or is it a bad relay?

Is there a problem with the brake light?

There is no problem with the driver side or left turn signal lights Since the STOCK tail light is red for brakes and amber for signal there are two seperate bulbs, not likely a bulb problem.The brake light circuit is shorted/bleeding into the signal light circuit! Is it wired for towing a trailer?

When does pressing the brake pedal the passenger side turn?

If pushing on the brake will illuminate the signal lights then turning on the signal lights has got to illum. the brake lights NOW where this short is that’s what you or a repair shop will have to find! It is going to be at the rear light or wiring as the two circuits do not pass through a common switch or circuit. Not on this vehicle!!

Why do my blinkers stop blinking when I apply the brake?

All of these problems mentioned can be the result of a bad ground. When you operate both blinkers and brake lights and the blinkers stop blinking, it’s because the circuit is not good enough to operate both lights. Bad ground. Same with headlights and blinkers. Probably the same with fog lights.

Why do my turn signals stop flashing when I apply the brake?

Make sure you have the right bulbs in and check the wiring harness on your lights and take a look inside the light assembly for any short circuit. Also any addition like the third brake light and, like mayer said, a trailer light plug that is shortened can do it too. Good Luck to you Was this answer helpful?

What to do when your brake lights are not working?

In the situation when brake lights are not working properly, you need to make sure that the power is going through and check the fuse. If the brakes lights are turned on at the same time as turn signal lights, you need to bring it to the mechanics for a check.

Is the left rear brake light corroded?

I went over and check the wiring to the affected side (left rear brake light/parking light) and sure enough, all of the ground wire connections were corroded where they were connected to the tailight assembly.

Where are the brake lights on my car?

You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm. Any problem with the fuse box and light switch will affect the brake lights.

How does a turn signal work on a Ford Ranger?

Hazards switch and turn indicators share much circuitry (all lights and wiring to them) and most comes together at a common meeting point, the hazard switch. 1) you have blinking-clicking relay sound from both turn signal flasher and hazard circuit flasher relay. 5) or a short to ground exists at the hazard switch (unlikely unless a fuse if blown).

What are the bulbs on a Ford Ranger?

Or, you could check the Bulb Replacement Guide to identify the bulbs in your vehicle. High beam headlight & Low beam headlight: 9007 Front turn signal light ( blinker light) for 1988-2011: 3457 / 3457K / 3157 / 3157K / 3157A / 3157AK / 3157-SCK ( parking light) Rear turn signal light / Brake Tail light: 4157 / 4157K / 3157 / 3157K / 3156 / 3156K

when the brake is pushed in both the front and rear turn signal lights come on and stay solid even when the turn signal is on and they are on the passenger side only. Also when the turn signal is on for a right hand turn the brake light on the top of the cab blinks too.

Hazards switch and turn indicators share much circuitry (all lights and wiring to them) and most comes together at a common meeting point, the hazard switch. 1) you have blinking-clicking relay sound from both turn signal flasher and hazard circuit flasher relay. 5) or a short to ground exists at the hazard switch (unlikely unless a fuse if blown).

Or, you could check the Bulb Replacement Guide to identify the bulbs in your vehicle. High beam headlight & Low beam headlight: 9007 Front turn signal light ( blinker light) for 1988-2011: 3457 / 3457K / 3157 / 3157K / 3157A / 3157AK / 3157-SCK ( parking light) Rear turn signal light / Brake Tail light: 4157 / 4157K / 3157 / 3157K / 3156 / 3156K

If pushing on the brake will illuminate the signal lights then turning on the signal lights has got to illum. the brake lights NOW where this short is that’s what you or a repair shop will have to find! It is going to be at the rear light or wiring as the two circuits do not pass through a common switch or circuit. Not on this vehicle!!

Author Image
Ruth Doyle