When do fault codes 3 and 4 stop blinking?
When do fault codes 3 and 4 stop blinking?
•Note: Fault Code Nos. 3 and 4 are first level faults. Avoid interpreting them as second-level Fault Code Nos. 33 and 44, which have not been assigned as fault codes. Restoring Fault Code Blinking – The fault code stops blinking after five minutes (15 minutes, Series HGJAA). Press Stop three times within five sec- onds to restore blinking.
What does it mean when the indicator light blinks 4 times?
Following a fault shutdown, the indicator light will repeatedly blink 2, 3 or 4 blinks at a time. • Two blinks indicates a low oil pressure fault. • Three blinks indicates a service fault. Press Stop once to cause the two-digit, second- level fault code to blink.
What does it mean when your computer blinks 3 times?
• Three blinks indicates a service fault. Press Stop once to cause the two-digit, second- level fault code to blink. (Pressing Stop again will stop the blinking.)The two-digit code con- sists of 1, 2, 3, 4 or 5 blinks, a brief pause, and then 1 to 9 blinks.
What does the Ol code mean on my Whirlpool washer?
The OL error code indicates that the washer is overloaded. If the washer is not overloaded, this would indicate either a drag on the drive system or the control board is failing. Be sure nothing is on the floor under the washer that could be causing a problem.
•Note: Fault Code Nos. 3 and 4 are first level faults. Avoid interpreting them as second-level Fault Code Nos. 33 and 44, which have not been assigned as fault codes. Restoring Fault Code Blinking – The fault code stops blinking after five minutes (15 minutes, Series HGJAA). Press Stop three times within five sec- onds to restore blinking.
What are the error codes for the Bosch washer?
Bosch WFL 2060UC Washer Error Codes Fault Possible Causes Door open or won’t lock – Door left open. – Faulty door latch or No water filling – Water shut off. – Inlet strainer filte No heating – Faulty heater. – Voltage too low. – Ex No draining – Blocked sensor. – Faulty water level c
What does it mean when the genset controller blinks?
The genset controller provides extensive diagnos- tics by causing the status indicator light on the Con- trol Switch to blink in a coded fashion. Following a fault shutdown, the indicator light will repeatedly blink 2, 3 or 4 blinks at a time. • Two blinks indicates a low oil pressure fault. • Three blinks indicates a service fault.
What does EA error code mean on LG air conditioner?
The EA error code indicates that the unit has detected a software issue. The unit will require a repair service. Please visit our Request a Repair page. The P2 or FL error code (depending on model) indicates that the drain pan in the unit is full. Under normal operating conditions, the drain pan will not need to be emptied.
What is the Flash code for the air bag?
Lamp flash code: 23 1.54 DTC B2295 Error value 26: Passenger side air bag circuit short to ground. Lamp flash code: 23 1.55 DTC B2295 Error value 25: Passenger side air bag circuit open circuit. Lamp flash code: 23 1.56 DTC B2295 Error value 24: Passenger side air bag circuit low resistance on squib.
What does it mean when your airbag light is blinking?
There are several reasons. It could mean that your battery backup is drained, that you have a worn-out airbag clock spring, or that your SRS airbag control module is faulty. It can also mean that something is wrong with your seat belts or impact sensors.
What is the Flash code on a lamp?
Lamp flash code: 42 1.63 DTC B2434: Driver safety belt buckle switch short circuit to ground. Lamp flash code: 51 1.64 DTC B2435: Driver safety belt buckle switch resistance out of range. Lamp flash code: 51 1.65 DTC B2438: Passenger safety belt buckle switch short circuit to ground.
