What was the horsepower of a 1973 Corvette?
What was the horsepower of a 1973 Corvette?
Instead, a choice of three hydraulic lifted units were available. The base 350 engine (RPO L48), which came standard with the 1973 Corvette, offered consumers a relatively unimpressive output at 190 horsepower. An optional, uprated small block (L82) was also offered with an engine output rating of 250 horsepower.
Where is the transmission on a 1973 Corvette?
The Muncie M20 wide-ratio 4-speed has been installed behind a 190-hp, 350-ci engine in this 1973 Corvette. (Note the shifter, shifting levers, and the reverse lockout cable.) The transmission is attached to the frame with two bolts on a bracket that bolts to the frame and to the transmission extension. The exhaust is also mounted onto this bracket.
What kind of engine does a C3 Corvette have?
I have installed many of the very popular Chevrolet Performance ZZ4 350- ci replacement engines in C3s. These engines pump out 355 hp with 405 ft-lbs of torque. The assembly comes with an intake manifold, water pump, oil pan, and HEI distributor.
How to install a ZZ4 GM crate engine?
Install the spark plugs, fuel pump, fuel lines, power steering pump, alternator and A/C compressor. Install all pulleys, fan and belts. Reconnect the radiator, heater hoses and fill radiator with coolant. Install starter, connect wiring, and vacuum hoses.
What kind of engine does a 1976 Corvette have?
1976 Corvette Specs Type: V8 Valve Location: In Head Bore / Stroke: 4.00″ / 3.48″ (Standard, L82 350 Cubic I Displacement: Standard, L82 Engines: 350 Cubic Inches
Install the spark plugs, fuel pump, fuel lines, power steering pump, alternator and A/C compressor. Install all pulleys, fan and belts. Reconnect the radiator, heater hoses and fill radiator with coolant. Install starter, connect wiring, and vacuum hoses.
How many horsepower does a 1979 Corvette have?
The 1979 Shark’s owner had the engine configured per his requirements: plenty of torque with regular gasoline. The dynamometer tested 383, had 401 hp, and 450 ft-lbs of torque. Hooker Super Competition headers were used to make sure all the available horsepower could be utilized.
How to install the emission system on a 1973 Corvette?
Pooff!! 1973-1982 Corvette Emission System Install: 01: This is a complete emission system for our 73 Corvette: Pump, diverter valve, injector tubes, check valves, EGR valve, diverter elbow, gaskets, vacuum hoses, smog hose set, PCV valve and clamps. You will also need a shop manual and assembly manual which are also available from Zip.
What kind of engine does a corvette 350 have?
In 2011, the 350 remained a highly sought replacement engine for restorations and use in performance cars primarily because its 4-inch bore and 3.48-inch stroke is the most common engine size. The L48 was the first version of the base 350 V-8.
What is the top speed of a 1973 Corvette Stingray?
how fast is this car ? top speed: 197 km/h (122 mph) (©theoretical); accelerations: 0- 60 mph 7.1© s; 0- 100 km/h 7.4© s (simulation ©automobile-catalog.com); 1/4 mile drag time (402 m) 15.3© s (simulation ©automobile-catalog.com) 1973 Chevrolet Corvette Stingray 350-4 V-8 Turbo-Fire 250-hp 4-speed close (man. 4) Detailed Performance Review
When did the L48 Corvette engine come out?
by Rob Wagner. The L48 350-cubic-inch V-8 engine was a base power plant produced from 1967 to 1980. The L82 350 was a performance version of the base 350 and manufactured between 1973 and 1980.
Instead, a choice of three hydraulic lifted units were available. The base 350 engine (RPO L48), which came standard with the 1973 Corvette, offered consumers a relatively unimpressive output at 190 horsepower. An optional, uprated small block (L82) was also offered with an engine output rating of 250 horsepower.
What was the front end of a 1973 Corvette?
The 1973 Corvette front fenders featured a simpler, recessed air vent design. The rest of the front end saw other modifications to their earlier design as well.
What was the casting number on a 1973 Corvette?
Although only 4 sets of wheels were ever recorded as being sold to consumers during the time of vehicle production, it is believed that Chevrolet manufactured as many as 800 sets of these unique aluminum wheels. These rare aluminum wheels carry the casting number 329381, and featured lug nuts with a recessed center area that had been painted black.
What kind of oil does a 1973 Corvette use?
1973 Corvette Specs Oil Pressure Gauge Mechanical Crankcase Oil Capacity, Standard, L82 En 4 Quarts, Less Filter Crankcase Oil Capacity, LS4 Engine 5 Quarts, Less Filter Recommended Oil Grade Above 20°F: SAE 20W, SAE 10W-30, 10W-40,
Finally, in 1973, GM introduced the 454ci LS4 as an available engine option for the Corvette. Rated at 270 HP, the LS4 was a far cry from the L88 of less than a decade prior, yet impressive nonetheless, when compared to other manufacturer’s offerings of the era.
What kind of engine does a corvette 454 have?
LS5 Specifications. All 454s had a 4.251-inch bore and 4-inch stroke. The 1970 LS5 featured a four-barrel carburetor and 11.25-to-1 compression ratio to deliver 360 horsepower for the Chevelle and 390 horsepower for the Corvette. The torque rating for both cars was 500 foot-pounds.
What kind of engine does a 1970 Corvette have?
The LS7 was still available in 2011. The detuned LS4 454 powered the 1973 and 1974 Monte Carlos, Chevelles and Corvettes. All 454s had a 4.251-inch bore and 4-inch stroke. The 1970 LS5 featured a four-barrel carburetor and 11.25-to-1 compression ratio to deliver 360 horsepower for the Chevelle and 390 horsepower for the Corvette.
Finally, in 1973, GM introduced the 454ci LS4 as an available engine option for the Corvette. Rated at 270 HP, the LS4 was a far cry from the L88 of less than a decade prior, yet impressive nonetheless, when compared to other manufacturer’s offerings of the era.
When did the Chevy 454 V8 engine end?
The Corvette followed suit by the end of 1974 and also bid farewell to this once powerful engine. The good news is that the 454 didn’t completely die after 1974 but was used up until 1996 in many Chevy heavy duty trucks.
What kind of suspension does a 1973 Corvette have?
The Vette is the kind of car that brings out the driver in you. When Chevrolet introduces something new, Corvettes usually have it first, but the 1973 Corvette got a lot that was all its own. Like disc brakes at all four wheels, independent suspension at all four corners, headlights that tuck out of sight, and bucket seats that hold just two.
All things considered, the 1973 L82 equipped Corvette produced 210 horsepower at 5,500 RPM, which served as a noticeable decrease in performance over past small-blocks within the 350 cubic-inch family. However, the L82 still managed to best the Corvette base engine’s output by 30 horsepower.
The Vette is the kind of car that brings out the driver in you. When Chevrolet introduces something new, Corvettes usually have it first, but the 1973 Corvette got a lot that was all its own. Like disc brakes at all four wheels, independent suspension at all four corners, headlights that tuck out of sight, and bucket seats that hold just two.
What engine is in a 1973 Corvette?
The base 350 engine (RPO L48), which came standard with the 1973 Corvette, offered consumers a relatively unimpressive output at 190 horsepower. An optional, uprated small block (L82) was also offered with an engine output rating of 250 horsepower.
What are the dimensions of a 1973 Corvette?
The 1973 Chevrolet Corvette C3 measures 69.00 inches in width, 182.50 inches in length, and has a wheelbase of 98.00 inches.
What are the timing specs on a Chevy 350?
The 350’s timing specifications are almost identical to the other small blocks. However, the ignition timing for the 255-horsepower version with manual transmission is at Top Dead Center and 4 degrees BTDC with automatics.
What are the dimensions of a Chevy 350 engine?
Chevy 350 Engine Specs. The Chevy 350 engine is a 350 cubic inch (5.7-liter) small block V8 with a 4.00 and 3.48 inch bore and stroke.
Although only 4 sets of wheels were ever recorded as being sold to consumers during the time of vehicle production, it is believed that Chevrolet manufactured as many as 800 sets of these unique aluminum wheels. These rare aluminum wheels carry the casting number 329381, and featured lug nuts with a recessed center area that had been painted black.
What are the engine numbers on a corvette?
The 327 engine in my Corvette contains the following number sequences: 6122891 F0518HE. Decoded, the first sequence is 6 for the year (66) and then the VIN sequence of 122891. The second stamp decodes F for the Flint Plant, May 18 is the engine assembly date and the HE suffix code stands for a 327 ci 300 hp with a manual transmission.
What was the serial number of a 1955 Corvette?
In 1955-56, it was simply a continuous serial number, but one that didn’t match the serial number of the Corvette. It was then followed with F for Flint, where the Corvette engine was manufactured and then the year (F55 or F56). The final two letters indicated the original application of the engine.
The 327 engine in my Corvette contains the following number sequences: 6122891 F0518HE. Decoded, the first sequence is 6 for the year (66) and then the VIN sequence of 122891. The second stamp decodes F for the Flint Plant, May 18 is the engine assembly date and the HE suffix code stands for a 327 ci 300 hp with a manual transmission.
What does it mean when your Corvette has matching numbers?
A matching numbers Corvette means that its Vehicle Identification Number (VIN) and the stamp on its engine match, proving that the original engine is still in the car. Numbers matching can also extend to the transmission, alternator, starter, and other components.
