What should the cooling temperature be on a 1984 Corvette?

1984 Corvettes will have the most noticeable improvement, as the factory cooling fan setting is 238 degrees. Lower temperatures will work at the expense of fuel mileage. There are various cooling fan control switches available to turn the cooling fans on earlier than the factory ECM or PCM controlled settings.

When to turn off the cooling fan on a corvette?

We recommend using a cooling fan switch that matches the thermostat opening temperature. For instance, our 244455 fan switch turns the fan on in the 200 degree range. When the engine coolant temperature drops below 185 degrees, the cooling fan is turned off.

What’s the water temp in a Chevy Corvette?

Dads 85 does the same thing. Fans wont even kick on till 240 or so but down the highway its 200-210 wich I believe is normal In cooler weather, it’ll run around 195 before t-stat opens, gets down to 186, and starts to climb again. It seems to run at about 200-206 while driving, and while idling go quickly to 226 degrees.

What should the thermostat be on a corvette?

Don’t forget the 242135 thermostat gasket to properly seal the thermostat housing. Another scenario would be the use of a 195 degree thermostat with the 244455 switch. The fan would run almost constantly as the thermostat regulates the temperature at 195 degrees.

What should the fan temperature be on a 1984 Corvette?

For this reason, we recommend using a minimum 180 degree thermostat and turning on the cooling fans at the 200-205 degree range. 1984 Corvettes will have the most noticeable improvement, as the factory cooling fan setting is 238 degrees.

What should coolant temp be on Corvette 85?

Your 85 came with one main fan and an auxillary fan was an option. The main fan is ECM controled to come on at 227*. If you have the aux fan (found under the front bumper infront of the radiator and is controled by a switch in the right head between #6 and #8 plugs), it will come on at 238*.

What’s the normal temp for a 1993 corvette?

I have a 1993 corvette what’s a normal temperature mine seems to run up to 210 and 220 is this Normal 6 people found this helpful. 200 to 220 is normal. Car is high perf. and built this way.

How do you change the temperature on a corvette?

Disconnect the temperature sender connector at the sender. Connect the center lead of the potentiometer to the connector in the wiring harness and the other to a ground. With someone in the car, turn the ignition switch to ON or ACC and adjust the potentiometer until the gauge reads 180 degrees.

Why is it important to keep your corvette cool?

Keeping your Corvette’s engine cool, especially during summer temperatures or performance runs, can make the difference between cruising along the coastline in comfort or walking along the roadside back home. We’ve assembled some common steps below to help maintain your vehicle for those long runs on sunny days.

What kind of cooling system did corvettes have?

GM had a B4P cooling system option available for 1985-1989 Corvettes. This option consisted of an extra cooling fan in front of the a/c condenser, heavy duty radiator and oil cooler.

What should I use to cool my Corvette radiator?

If coolant is not at this level during operating conditions, coolant should be added only to the reservoir to raise the level to the “FULL” mark. Use a 50/50 mixture of high-quality ethylene glycol anti-freeze and water when adding coolant. Wash radiator cap and filler neck with clean water. Check coolant for proper level and freeze protection.

Where are the relays on a corvette radiator?

The cooling fan relays are mounted on the driver side of the radiator housing. 1990-1993 Corvettes have two relays: a primary and a secondary. 1994-1996 have three relays: primary, secondary and one relay for half speed fan operation.

GM had a B4P cooling system option available for 1985-1989 Corvettes. This option consisted of an extra cooling fan in front of the a/c condenser, heavy duty radiator and oil cooler.

How can I make my Corvette cooling fan run simultaneously?

Connect one of the new harness wires to the dark green/white wire. Route the other harness wire to the main fan relay (near the battery). Locate the dark green/white wire at the relay connector. This will make both cooling fans come on simultaneously, meaning less run time for both fans if the cooling system is in good condition.

Where is the low temp fan switch on a 1996 Corvette?

1985-1996 Corvette Low Temp Cooling Fan Control Switch would be installed in this location (driver’s side cylinder head between cylinders 1 and 3). Cut the dark green /white wire at the inner fender well.

What should the cooling temperature be on a 1984 Corvette?