What is the ignition switch on a 1987 Ford Ranger?

The ignition switch is a small but essential component on your 1987 Ford Ranger. It allows you to start the vehicle using your key. Once inserted into the ignition cylinder, the key can be turned to five positions: Lock, Off, Run, Start and Accessory.

How can I test my Ford Ranger ignition?

Plug the electrical wiring into the new ignition switch. Reconnect the battery cables and turn the key in the ignition switch to test it for proper operation. If the ignition works properly and your Ford Ranger starts, turn off the engine and reinstall the shrouds onto the steering column by screwing in the two screws…

What to do when your Ford Ranger wont start?

Reconnect the battery cables and turn the key in the ignition switch to test it for proper operation. If the ignition works properly and your Ford Ranger starts, turn off the engine and reinstall the shrouds onto the steering column by screwing in the two screws that you removed earlier.

How do you take the steering wheel out of a Ford Ranger?

Remove the key from the ignition and put it in a safe place. Place one hand on the top and one hand on the bottom of the upper extension steering wheel shroud and squeeze to remove it from the retaining plate. If your Ford Ranger does not have tilt steering, this step is not required.

When did the 2.0 liter Ranger come out?

The 2.0/2.3 liter versions that were offered in Rangers starting in 1983 used a different head having four evenly spaced round holes of equal size. A 2.0 liter 1bbl carbureted version was offered in Rangers from 1983 – 1985, and in 1987 – 1988 with a 2bbl carburetor in some parts of the US, Canada and Mexico.

When was EFI added to the Ford Ranger?

Electronic Fuel Injection (EFI) was added to the engines in 1985. In 1989 the 2.3 was changed to a DIS (Distributorless Ignition System) ignition utilizing a new 8-plug head ( 2-plugs per cylinder). This head had larger evenly spaced D-shaped intake ports and was used until the end of production of the 2.5 in 2001.

What kind of engine does a Ford Ranger have?

Ford Ranger 4-Cylinder Engines Displacement 140 CID Type Dual Over Head Cam Bore x Stroke 3.445 x 3.7010 inches Compression Ratio 9.7:1

When did Ford add the CPS to the Ranger?

CPS (Cam Position Sensor) was added starting in 1995 (1994 in California). At this time Ford changed to a 104-pin computer (it was a 60-pin) and moved the DIS functions into the computer, previously the DIS system had a TFI module as a separate unit mounted on the front of the intake manifold. The 2.0 is an underbored 2.3.

What was the name of the 1987 Ford Ranger?

1987 Ford Ranger – A new 4×4 model was introduced called the High Rider STX that included a bed-mounted light bar and tubular grille guard.. It had 1.5 inches more ground clearance than the previous year’s 4×4 model.

When was the first Ford Ranger truck made?

1983 Ford Ranger – Replacing the Mazda-built Courier for 1983 was the Ford-built Ranger truck. Introduced early in the 1982 calendar year, the Ranger was nearly the same size as the Courier and also offered 6 and 7 foot beds.

When did the Ford Ranger become a pickup?

It took thirteen years, but eventually, the Ranger found its place as a pickup for people who just needed a pickup. The path for the Ranger to become its own line instead of a trim package in the F-Series started in the ‘80s. When Ford introduced the F-150, it quickly took over the F-100’s sales, making the two pickup trucks redundant.

How much does a 1987 Ford Ranger cost?

It is in need of a new power steering pump (the part is $40), coolant hoses ($15 each), a heater core ($30-$40) and it will also need a new windshield eventual… It is in need of a new power steering pump (the part is $40), coolant hoses ($15 each), a heater core ($30-$40) and it will also need a new windshield eventually.

What does the ignition switch do in a Ford?

The ignition switch in Ford vehicles is responsible for handling the electrical signals related to starting the vehicle.

What’s the best way to change an ignition switch?

Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue.

Can a bad ignition switch cause a car to not start?

by Jonathan Lister. The ignition switch in Ford vehicles is responsible for handling the electrical signals related to starting the vehicle. A failing ignition switch can cause system-wide problems ranging from the ability of the car to start, to maintaining speed and even keeping the radio turned on.

The ignition switch in Ford vehicles is responsible for handling the electrical signals related to starting the vehicle.

Where is the Ford crest logo on the ignition switch?

These have a Ford crest logo on top of the key similar to the hood emblem plastic 0A-16637. Fits vehicles… (and/or) additional info… Fits vehicles… (and/or) additional info… Tech Tip: 1941-47 Pass and Merc, the case will have to be opened to install the new plate.

How to fix ignition problems by replacing the ignition switch?

How to fix ignition problems by replacing the ignition switch. Ignition switch location, inspection, removal and repair. DIY car repair with Scotty Kilmer, an auto mechanic for the last 43 years. 1. Screwdriver set: http://amzn.to/2j92UCG 2. Disposable Gloves: http://amzn.to/2zSRuxO 3. Common Sense 4. Full HD Camera: http://amzn.to/2AvoEk7 5.

What are the symptoms of an ignition switch failure?

Careful car owners can recognize the symptoms of ignition switch failure before the problem leaves them stranded on the side of the road. An ignition switch performs several functions for a vehicle.

How do you put a new ignition switch in a car?

Insert your car key into the replacement ignition switch and turn it to the “Run” position. Place the new ignition switch on the actuator pin and make sure the holes on the switch base are lined up with the holes on the cylinder housing. You may have to adjust the cylinder slightly to align it with the U-shaped slot on the actuator.

Can you remove the ignition switch from a 1985 Ford Ranger?

The ignition switch on your 1985 Ford Ranger comes equipped with special brake-off head screws impossible to remove with a regular screwdriver or similar tool. You can remove the screws at home, however, by using a special tool that’s readily available at most auto parts stores.

How do you remove the battery from a Ranger?

Remove the Ignition Switch. Detach the ground (black) battery cable using a wrench. Make sure the ignition lock cylinder is in the Lock position and remove the key. Remove the upper extension shroud from the steering column, if your Ranger model comes equipped with a tilt column.

How do you remove ignition switch from steering column?

Remove the two switch mounting bolts. Use an electric drill with a 1/8-inch (3mm) drill bit to drill a hole on the center of the brake-off head screws. Then use an Ex-3 Easy-out tool to unscrew the two mounting bolts. Disengage the ignition switch from the actuating pin by hand and remove the switch from the steering column.

How do you remove the ignition switch from a car?

Use an electric drill with a 1/8-inch (3mm) drill bit to drill a hole on the center of the brake-off head screws. Then use an Ex-3 Easy-out tool to unscrew the two mounting bolts. Disengage the ignition switch from the actuating pin by hand and remove the switch from the steering column.

Where is the ignition switch on a Ford?

The Lock Cylinder What is often called the “ignition switch” is actually two components: the lock cylinder, and the electric switch. The lock cylinder is the housing into which a vehicle’s starter key is inserted, and the electric switch is located just behind it.

How is the ignition switch connected to the trunk?

You might consider getting a matched lockset that includes the door and trunk cylinders. The ignition switch itself is connected to the ignition cylinder by a shaft or lever. Inside the ignition switch, several contacts connect vital electrical systems needed to start and run the car.

What should I do if my ignition switch is not working?

How To Fix It: After ensuring the rest of the electrical system is intact, such as fuses, relays, and circuits, replace the ignition switch. The transponder antenna surrounds the ignition cylinder. If it doesn’t recognize the transponder key, it doesn’t allow the engine to run. https://www.gettyimages.com/license/525320791

Can a bad ignition switch cause a car to stall?

Problems with the lock cylinder may be intermittent with the position slipping while the car is operating which will cause sluggish acceleration and stalling.

What should I do if I need to replace my ignition switch?

Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue. If it doesn’t, remove the ignition switch and reinstall it. Shut the engine off (if it starts) and disconnect the battery again.

Where is the release pin on an ignition switch?

The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.

What to do when ignition switch breaks off?

Screw in the new break-off bolts until the bolt heads break off. The bolt heads will break off at about 3 to 4 foot-pounds of torque. Plug the electrical wiring into the new ignition switch. Reconnect the battery cables and turn the key in the ignition switch to test it for proper operation.

What is the ignition switch on a 1987 Ford Ranger?