What is the Chevy check engine light code?

Answer: Hi Onnie. Your code is a P0332 Knock Sensor 2 Circuit Low Input (Bank 2). With a code like a P0332 you’re likely to find the problem lies with the knock sensor on bank 2 (that’s the side of the engine that doesn’t have cylinder #1), or with the associated wiring & connections.

What causes a Chevy 350 to backfire constantly?

The air intake boot or tube transfers air from the mass air flow sensor into the throttle actuator and then into the engine. If there is a problem with these parts such as a tear or rip it will allow un-metered air into the engine which the computer will see via the oxygen sensor which in turn will deliver less fuel creating a lean condition.

Is it safe to clear a misfire code on a Chevy truck?

Yes, your truck does need attention. When the truck ran out of gas it likely set a misfire code, and possibly other codes. It should be safe to just clear the trouble codes. If any engine light codes return, the truck will need further attention. Good luck!

What to do if your check engine light is not working?

Start by inspecting the wiring and connectors, repair as required. If everything is fine, check the sensor using a DVOM (digital volt ohm meter). Replace if necessary. You can find the proper resistance values using a repair manual or comparing the sensor reading on bank 2 to that of bank 1. Good luck with your knock sensor issue!

How many miles does a 1990 Chevy Blazer have?

(866) 715-XXXX (866) 715-XXXX 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 of 20 Full size photos Full size photos Vehicle Details 1990 K5 Blazer Silverado 132k original miles Factory TBI 350 Runs Strong Factory AC Power windows and power door l… About this vehicle This 1990 Chevrolet Blazer is an original.

What to do if your Chevy Blazer engine isn’t working?

Replace your worn-out Chevrolet Blazer engine with a quality engine from AutoZone. There are several warning signs that the engine on your Blazer isn’t working.

Where can I get a new Chevy Blazer engine?

10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only If you depend on your Chevy Blazer to handle your everyday commute, a faulty engine is definitely something you don’t want to mess around with. Replace your worn-out Chevrolet Blazer engine with a quality engine from AutoZone.

What causes a flashing check engine light on a Chevy Silverado?

While a majority of the time, the flashing check engine light is going to be caused by a misfire related to your Silverado’s ignition system or fuel system (as stated above), there are other issues that can cause it. Your timing chain could have jumped .

Are there any problems with the Chevy Silverado 2500?

Chevrolet Silverado 2500 owners have reported 21 problems related to check engine light on (under the engine and engine cooling category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Chevrolet Silverado 2500 based on all problems reported for the Silverado 2500.

What kind of engine light does a Chevy Tahoe have?

Some Chevy vehicles include Silverado, Suburban, Cavalier, Trailblazer, Tracker, Tahoe, Cobalt, and more. 2003 Chevy Silverado 1500 P0327 – I accidentally sank the truck in a creek and now I have a P0327 code, what is the problem? 2003 Chevy Tahoe 5.3L P0135 Engine Light Code – I have a 03 Tahoe with a P0135 code that won’t go away. Help!

What is the diagnostic code for a Chevy check engine light?

Remember, these are manufacturer specific codes only. Refer to our Generic OBD II code list for definitions on all other Chevy diagnostic trouble codes. Manufacturer Specific Codes P0342Camshaft Position Sensor A Bank 1 Low Input – Related Information P1031HO2S Heater Current Monitor Control Circuit Sensors 1

What kind of car has a check engine light?

Tl-the contact owns a 2002 Chevrolet Silverado 2500. The contact stated that while driving at 65 mph, the engine stalled without warning. The check engine light illuminated. The vehicle restarted after numerous attempts.

What to do if your Silverado is ignoring the Check Engine light?

If you don’t already have a trouble code scanner, swing by an auto parts store and pick one up or have them run a diagnostic using their own scanning tool. Even if your Silverado is running like usual, ignoring the check engine light can result in costly repairs down the line.

What should I do if my check engine light comes on?

While yes, both yourself and AutoZone can read the engine computer’s stored codes, and through Fix Finder, determine likely causes based on thousands of mechanics intel, none of these can pinpoint with 100% accuracy exactly why the CEL came on.

How does AutoZone check engine light finder work?

An easy-to-use tool to troubleshoot why your Check Engine Light is on, Fix Finder utilizes an extensive database of repair solutions from ASE certified mechanics to help you get to the most likely fix. How does AutoZone Fix Finder work?

What does it mean when service engine light comes on?

When the light comes on, a code is stored as the reason for triggering the light. When you take your car in to get it checked out, the mechanic hooks up a little diagnostic computer to your vehicle’s computer. They will then get a code and description that tells them what the issue is.

Can you scan the Check Engine light at AutoZone?

In this case, the Malfunction Indicator (Check Engine) lamp on the vehicle’s instrument panel will light steady on. Remember to return the scan tool to an AutoZone employee when finished. These tools will not work with any other device other than the Z-Net terminals at AutoZone.

What does the red light on the Check Engine light mean?

Red X – Indicates a problem with one or more of the vehicle’s systems. The red LED is also used to show that DTC (s) are present. In this case, the Malfunction Indicator (Check Engine) lamp on the vehicle’s instrument panel will light steady on. Remember to return the scan tool to an AutoZone employee when finished.

Why does my check engine light come on when I leave my cap off?

If you leave your gas cap off accidentally, you’ll notice this light rather quickly. These leaks in the gas tank recirculation (also known as EVAP emission control) system are often grouped as “small” or “large” leaks.

Why does my Check Engine Light never come on?

The C/K line includes pickup trucks, medium-duty, and heavy trucks. When I turn the ignition on, all of the lights on the dash turn on and then go off. But the check engine light never turns on. How do I make it come on?

Is it safe to clear a misfire code on a check engine light?

Answer: Hi Matt. Yes, your truck does need attention. When the truck ran out of gas it likely set a misfire code, and possibly other codes. It should be safe to just clear the trouble codes. If any engine light codes return, the truck will need further attention.

Why does my check engine light not turn off?

Sometimes your check engine light won’t turn off even after you’ve fixed the problem with your vehicle. When that happens, you’ll need to manually reset the light. One option is to turn the ignition on and off 3 times in a row. Then, drive your vehicle around and check to see if the light goes off.

Where to find diagnostic code for Buick check engine light?

1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3. Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s).

What is the oxygen sensor code for a Chevy?

P1137HO2S Bank 1 Sensor 2 Lean Or Low Voltage – Read Our Article On Oxygen Sensor CodesFor Help With This Chevy Trouble Code P1138HO2S Bank 1 Sensor 2 Rich Or High Voltage – Read Our Article On Oxygen Sensor CodesFor Help With This Chevy Check Engine Light Code

Why does my check engine light keep coming on?

Common problems that can trigger Chevy check engine lights to stay on include: First, check the gas cap and make sure it is on tight. If the light doesn’t reset within the next two to three days, read the fault codes. How to Reset Check Engine Light on a Chevy?

Where do I find the trouble code on my Chevy?

These are listed in numerical order for easy searching. When retrieving Chevy trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.

What should I do if my check engine light is still coming on?

Put the keys in your ignition and turn your ignition on and off consecutively after a second in each step. Once it is done, see if the engine check light is still coming on or not. If the check light is off, you are ready to go, but if it is still coming on, get ready by reading the codes with a scanner instead. Let it Go Off Itself

What to do if your check engine light is still on?

If the check engine light is still on after three days, your problem may not have been fixed or you may need to try some of the methods below to reset it. 2. Turn the Car on and off Three Times Some vehicles will automatically reset the trouble codes that caused the initial error after the vehicle is turned on and off three times in succession.

What does the Check Engine light mean on a 2005 Chevy Colorado?

At the 100,000 mile mark the check engine light comes one indicating the #2 coil is bad. This doesn’t seem to be the problem nor is it in the injectors. It seems with the online forums that are out there indicates there was a problem with the head on the 2005 Colorado but Chevrolet or gm is not investigating or talking about it.

What are the problems with the Chevrolet Colorado?

See all problems of the 2018 Chevrolet Colorado . The check engine light came on it popped up engine power reduced wouldn’t go over 35 miles and hr on the interstate is not a good thing. I pulled over turned car off. Turned key back on started it was fine. A couple weeks later pulling out in traffic check engine. Light.

What was the mileage on my Chevy Colorado?

The approximate failure mileage was 6,999. Tl-the contact owns a 2004 Chevrolet Colorado. The contact stated that while driving at various speeds he noticed that the check engine light had illuminated. The vehicle was taken to a dealer and they advised him that the O2 sensor needed to be replaced. The vehicle was repaired for the O2 sensor.

What was the check engine warning light on?

The contact owns a 2006 Chevrolet Colorado. While driving approximately 40 mph, the check engine warning light illuminated and the vehicle began to decelerate. The vehicle was taken to an independent mechanic where the mechanic advised that the engine would have to be replaced. The vehicle was not repaired.

Can a car’s check engine light be reset?

Some of the possible malfunctions in your car can be detected either by various inappropriate sounds or by various physical signs. But some faults, that are not easily detectable but do occur in your vehicle are represented by the check engine light in your car. In this article, we will go through how you can reset the check engine light.

What’s the misfire code on a 1998 Vortec?

Can someone please help with what I should check next, I have a 1998 Chevy K1500 5.7 Vortec with a misfire, P0300 code for 3 months. runs a little rough, while driving under normal conditions it sputters, hesitates, and also will backfire, under heavy acceleration no noticeable skip, no sputters, and does not hesitate or backfire.

What causes a Chevy Silverado engine to misfire?

Keeping in mind that any engine needs air, fuel, and spark for ignition, your Chevy Silverado’s fuel system can often cause the engine to misfire. It can run too lean or rich.

When does a Chevy Colorado become a problem?

It becomes a problem around 90,278 miles and can cost from $65 to $112 to repair. 221 people reported the engine misfiring because of a worn valve seat. This had the additional inconvenience of turning the check engine light on. Most common in model years 2004-2009, most people noticed the issue around 107,358 miles.

What’s the weight of a Chevy Colorado LS?

This page describes the LS conversion of my 2004 Chevrolet Colorado ZQ8. The intitial build was completed in the spring of 2015 using a carb setup and the stock transmission. The stock Aisin 5 speed is rated for about 260 ft/lbs and a stock LR4 with the mods should be running about 325 ft/lbs. To date the transmission has held up admirably.

What kind of engine does Chevy Colorado have?

EPA estimated with 3.6L V6 engine. Cargo and load capacity limited by weight and distribution. Chevrolet Infotainment System functionality varies by model. Full functionality requires compatible Bluetooth and smartphone, and USB connectivity for some devices. Vehicle user interface is a product of Apple and its terms and privacy statements apply.

What does check engine light mean on 2016 Chevy Colorado?

A check engine light can indicate a broad spectrum of problems with your 2016 Chevrolet Colorado. In some cases you need to pull over immediately to prevent damage while in others you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light.

When does the Check Engine light come on?

Intermittent Check Engine Light: If the check engine light on your 2016 Colorado is intermittent, try to take note of the conditions when this happens. For example, does it happen when you accelerating, driving on the highway or does it appear at low speeds?

How long has my Chevy Colorado been in service?

The service manager reported this has been a problem with this particular engine and my online research revealed that Chevrolet recognized this problem and extended the warranty coverage to 7 years and 100,000 miles. My vehicle only had 87335 miles, but had been in service for 9 years, 7 months.

What are the warning lights on a Chevrolet?

The following are warning lights and indicators found in vehicles built by Chevrolet. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are nearly 50 of them so search carefully!

What should I do if my check engine light is not on?

Most vehicle manufactures also have their OEM codes that some Readers and Scanners can’t seem to read for lack of conversion ability. Check the make and model of your reader to see what it is built for and if all else fails, head into a parts store and they should be able to read the issue at no cost to you.

What does the code p0155 on a Chevy mean?

The code means the the sensor is taking too long to warm up. Replacing the Front Heated Oxygen Sensor (H2OS) Bank 2 usually takes care of the problem. The cost to diagnose the P0155 CHEVROLET code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What is the diagnostic code for a Chevy Duramax?

Below are common check engine light trouble codes for the Chevy/GM Duramax diesel. This list has been updated to includes Chevy/GM Duramax diagnostic trouble codes. At Thoroughbred Diesel we are a real diesel performance and repair shop that offers free advice. Call us at 1-866-737-4966 with any questions you may have about your diesel.

What makes the Check Engine light come on?

Lambda Sensor or Oxygen Sensor (Oxygen Sensor): the check engine lights if the voltage sensor delivers very low-almost 0 volts, or “high voltage”, close to the 12 volt battery / generator: Codes P0131 and P0132 respectively . This sensor can also generate the code No Activity P0133.

What does the yellow light mean on a corvette?

After all, the light is yellow rather than red, which typically means “proceed with caution” unless the engine performance is so compromised your Corvette can’t proceed. If the Check Engine or SES warning light comes on, glance at the gauges.

What causes a glowing service engine soon light?

The most likely cause is a poor connection at the knock sensor or a battery voltage discrepancy. The owner has been driving the car lately with no issues. A few simple checks, battery terminal cleaning, and a battery takes care of what could have been misconstrued as a major issue.

What is the code for the Check Engine light?

IAT Sensor (Intake Air Temperature Sensor): the check engine lights if the voltage sensor delivers very low-almost 0 volts, or “high voltage”, close to the 12 volt battery / generator: Codes P0112 and P0113 respectively.

What should I do if my check engine light never comes on?

You can check to see if there is voltage on the lamp lead going to the ECU. If there is about 12 volts on it you should be able to ground that point and turn on the lamp to verify the rest of the circuit is ok.

When does the O2 sensor turn on the Check Engine light?

The engine control module (ECM) sees the voltage of the O2 sensor for bank 1 sensor 2 above 1.2 volts when the ECM has commanded the fuel to a targeted lean condition on that bank of the engine. The ECM detects the voltage high problem and turns on the Check Engine Light.

What does the Check Engine light on a Chevy Spark mean?

Chevrolet Spark engine warning light The Check Engine light is an alarm that goes on for several engine failure, and it is a wakeup call to do a review as soon as possible. There are many car owners do not even know the name of this board warning light, much less what to do when it turned on.

Why does my check engine light keep coming on and off?

But, there are other possible causes of intermittent illumination of the Check Engine Light such as failures in engine sensors, intermittent misfires, and faults with sticky or stuck valves such as in the EGR (exhaust gas recirculation) system or the EVAP system.

How many miles do you have to drive to turn off Check Engine light?

You have to drive 50 to 100 miles in several individual trips until the system reads the status of all the components again. “Several trips” means that you shut off the engine and start another trip.

Is it okay to drive with a flashing check engine light?

It’s never recommended to drive with a flashing check engine light. A constant check engine light can be okay to drive with sometimes, but a flashing engine light is most likely a more serious problem that has to be fixed as soon as possible.

What does a check engine light mean on a Chevy Silverado?

A check engine light can indicate a broad spectrum of problems with your 2004 Chevrolet Silverado 1500. In some cases you need to pull over immediately to prevent damage while in others you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light.

Intermittent Check Engine Light: If the check engine light on your 2004 Silverado 1500 is intermittent, try to take note of the conditions when this happens. For example, does it happen when you accelerating, driving on the highway or does it appear at low speeds? This will help your mechanic evaluate the issue.

How to troubleshoot a Chevy Silverado check engine?

To troubleshoot, make a note of which cylinder appears to be misfiring. Then swap that coil for another one on the vehicle. By swapping the coils, you can see if the issue goes away or if it follows the coil, which would indicate that the coil is bad and needs to be replaced. If playback doesn’t begin shortly, try restarting your device.

How to self test the Check Engine light for a c1500 Chevy?

Place the C1500 into self testing mode. To do this, insert the C1500’s key into the ignition and switch to the “On” position. Leave the C1500’s engine off and uncranked. Count how many times the C1500’s check engine light flashes and observe how long the flashes last. Each flash code is different.

What to do if your check engine light is blinking?

If the light is flashing, take your vehicle in IMMEDIATELY to be diagnosed and inspected–a flashing light indicates a serious problem with one of your vehicle’s components. If the light is not flashing, check the gas cap. Oftentimes if the gas cap wasn’t tightened enough, the check engine light will display.

What makes the Check Engine light come on on a Chevy Silverado?

Depending on the year and model of your Silverado, your truck can have up to four oxygen sensors. Unfortunately, a problem with any one of them can cause the check engine light to come on—but that’s not all.

Whenever the vehicle detects that something may be wrong–whether it’s an emissions-related problem, cooling system issue, engine problem or something as simple as a loose gas cap, in some cases–the Check Engine light will appear.

What to do if your Chevy engine light is blinking?

The easiest course of action is to bring your car over to the Service Department at Larry H Miller Chevrolet for one of our certified technicians to investigate the diagnostic code and isolate the cause.

What are the symptoms of a bad oxygen sensor?

Symptoms of a Bad or Failing Oxygen Sensor 1 Check Engine Light comes on The first line of defense is the Check Engine Light. 2 Bad gas mileage and rotten egg smell If the oxygen sensor is going bad, the fuel-delivery and fuel-combustion systems will be thrown off. 3 Rough engine idle and misfires

When to get an oxygen sensor replaced in your car?

As soon as you notice your Check Engine Light, poor gas mileage, or an irregular engine idle, book an appointment to have your oxygen sensor replaced. This will ensure your vehicle is running smoothly, efficiently, and will help prolong the life of your engine.

Can a bad sensor cause a check engine light?

Depending on your vehicle model, your engine might experience one or more of these performance problems: However, these symptoms are not exclusively symptoms of a failed MAP sensor. Sometimes, a bad sensor may trigger the check engine light (CEL).

What happens when the oxygen sensor goes bad on a Chevy Silverado?

Your Silverado can exhibit symptoms when the Oxygen sensor has gone bad. Or, it may exhibit none at all. Often enough, the only sign of the problem at all is the service engine soon light being on. The good news is, if you end up discovering that the oxygen sensor is bad, they really aren’t that expensive to replace.

Why does the Check Engine light come on on a Chevy Silverado?

Oxygen sensors can change the way that your Silverado’s engine runs. Most of the time, the check engine light will come on. It’s a good thing that the check engine light would come on, as there is more than one oxygen sensor, and they can be difficult to get to and test.

Which is the diagnostic code for a GMC check engine light?

1 Refer to our Generic OBD II code list for definitions on all other GMC diagnostic trouble codes. 2 Manufacturer Specific Codes 3 P1031 4 P1032 5 P1105 6 P1106 7 P1107 8 P1108 9 P1109 10 P1111

When to change spark plugs on Chevy Silverado?

P0304 and P0351 are common DTCs associated with faulty spark plugs, but you will know if you need to change the spark plugs if you notice any of the accompanying signs, including rough idle, engine surging, lack of acceleration, and high fuel consumption. Figure 1. A fresh plug versus a worn out one.

Why does my Chevy check engine light keep flashing?

A fault code is stored in the Engine Control Unit (ECU). Chevy check engine light should only be on for a few seconds when you turn on the ignition and should turn off once the engine fully starts. If your Chevy check engine light stays on or is flashing, get the vehicle diagnosed as possible.

How do you start a Chevy check engine light?

If your Chevrolet has Start/Stop button, you will need to press the START button without pressing the brakes. Allow your OBD2 scanner to turn on and connect to your Chevrolet Engine Control Unit (ECU).

How can I Reset my Check Engine light?

This step can take up to one minute. Read Chevrolet check engine light codes from the Engine Control Unit (ECU) using an OBD-II scanner. Once you have retrieved the codes, write them down. Research the codes and fix the underlying problem, you can come back and click Erase Codes to reset the Chevrolet check engine light.

Where is the diagnostic port on a Chevy?

Locate the diagnostic port under the dashboard of your Chevrolet on the driver’s side. This is a 16-pin port on all 1996, and newer Chevrolet vehicles have this port. Plug in your OBD2 scanner or Bluetooth adapter into the port. Turn the ignition ON, key in position II. All Chevrolet dashboard lights will turn on but do not start the engine.

What kind of engine light does a Chevy Silverado have?

This free video provides the steps to diagnose and clear a check engine light on a 2004 Chevrolet Silverado 1500 LS 5.3L V8 FlexFuel Extended Cab Pickup (4 Door). The video also provides steps on how to read the 2004 Chevrolet Silverado 1500 LS 5.3L V8 FlexFuel Extended Cab Pickup (4 Door) trouble code About Us Maintenance Parts & Tools Contact

When to reset check engine light on Chevy Silverado?

To reset the check engine light on the Chevy Silverado, watch:

How to clear service engine soon light 1990 to 2002 Chevy?

If playback doesn’t begin shortly, try restarting your device. As an Amazon Associate I earn from qualifying purchases. I am a participant in the Amazon Associates Program, an affiliate advertising program designed to provide a means to earn fees by linking to Amazon and affiliated sites.

Is the Check Engine light on a 2004 Silverado Z71?

I checked the chiltons book and it says 05 and up have only filters on the sending units and they are not replaceable. Since yours is an 04 its possible your in the same boat too. My 03 has an inline filter in the frame in the area below the drivers seat. According to the chilton’s book yours should too.

Which is the most accurate check engine light code?

P1270Accelerator Pedal Position Sensor A/D Converter Error P1271APP Sensor 1-2 Performance P1272Accelerator Pedal Position Sensor 2 P1273Accelerator Pedal Position Sensor 1

What causes a check engine light to come on?

4. Check Engine Light Comes On. A bad or failing catalytic converter can also cause an illuminated Check Engine Light. The oxygen sensor and air-fuel ratio sensor in modern vehicles monitor the efficiency of the catalytic converter by tracking the gas levels in the exhaust.

Why does my car make a rattling noise when I start it?

An engine rattling noise, or a clicking sound in an engine, can spring up from a number of sources. Whether it’s engine knocking when accelerating or some kind of spark knock or just a general engine noise, some are more serious than others, but there’s one thing that’s true of them all: it’s never good to leave it alone.

How do you turn off a check engine light?

If you don’t get a definition, look up the code in the owner’s manual or online. Press the “erase/clear” button on your scanner, then turn off the key and disconnect it. Clearing any codes present will turn off your check engine light temporarily.

Try removing a sensor harness and see if the light comes on. If it does, then the system is working. If it does not, then check the computer for codes for the sensor you unplugged. If there is a code, and the MIL indicator says ON, then the light is burned out.

Why does my catalytic converter rattle when I start the car?

If a catalytic converter becomes old or damaged internally from excessively rich fuel mixtures, the catalyst coated honeycomb meshes on the inside of the converter can collapse or break apart, causing a rattle. The rattle may be more obvious when starting the vehicle, and will get worse over time.

What to do if you see a warning light at AutoZone?

If you see a warning light, come to AutoZone Fix Finder reads information from the Check Engine, ABS, and maintenance lights. The test often takes less than a minute once the reader is plugged in. Find the closest store to you.

Why is the Check Engine light on on my Echo?

It’s usually something related to the emissions, like everyone else in the thread has said. Sometimes a loose gas cap will cause a drop in pressure in the fuel tank and that will set the CEL. My Echo has been doing that after nearly every fill up the last couple of months.

What makes the Check Engine light go away?

Oftentimes if the gas cap wasn’t tightened enough, the check engine light will display. If tightening the gas cap does not make the light go away, take the vehicle in to have the diagnostic codes looked up. If you follow those three simple rules and keep up on your vehicle’s maintenance, your vehicle will last you a long time.

When does the service engine soon light come on?

If your Check engine light is ON, the easiest way to diagnose this problem is to always check your trouble code memory with an OBD2 scanner. The check engine light will not light up if there is a scheduled service as the service engine soon light. It does only occur when there is a problem with your engine.

Is there a way to reset the Check Engine light?

Using a scan tool is the easiest way for check engine light reset. If you wonder to know how to turn off check engine light by this way, here are 3 steps for you. Connecting the scan tool to the OBD- II ( On- board diagnostic connector) under your steering column.

Where to plug in the Check Engine light?

Plug the reader into the OBD port of your vehicle. This port is usually located on the underside of the dash area just above the foot well. On some vehicles, you’ll have to remove the door on your fuse box to access this port. Once you have connected the reader, press the “enter” button to turn it on.

What to do if the Check Engine light comes on?

If the check engine light comes on, here are some tips on what you should do: Look for a serious problem that requires immediate attention. Check your dashboard gauges and lights for indications of low oil pressure or overheating. These conditions mean you should pull over and shut off the engine as soon as you can find a safe place to do so.

What can cause a check engine light to come on?

A loose gas cap can cause the check engine light to come on. A problem with a spark plug can cause the check engine light to come on.

What does the Check Engine light actually mean?

The check engine light is a signal that the onboard diagnostics system (or OBD II) has detected a malfunction in the vehicle’s emissions, ignition, fuel or exhaust systems. It could be caused by something as simple as a loose gas cap or a faulty oxygen sensor or spark plug or something as severe as…

How do you check the Check Engine light?

Put your key in the ignition and switch the vehicle to “on.” Do not start the vehicle. Once the lights on the dash come on, turn off all the vehicle’s accessories, like the radio. Then, press the “read” button on the scanner to access the check engine light code.

What to do when your dashboard light goes off on a Chevy Silverado?

Immediately stop the vehicle and switch off the engine if driving. Wait a few minutes for the oil to drain into the pan. Check engine oil level. If the engine oil level is within the acceptable level range, do not restart the engine and arrange to have the vehicle towed.

What are the warning lights on a Chevy Silverado?

Description: High engine coolant temperature warning may be indicated by the coolant temperature gauge, a warning light or warning message. For the coolant temperature gauge, it may display temperatures in Fahrenheit or Celsius. If the needle on the temperature gauge moves into the red area, immediately pull off the road and switch off the engine.

Why is my check engine warning light coming on?

The most common faults associated with the Chevrolet Silverado check engine warning light coming on are: Loose or faulty gas cap. Due to the loss of pressure inside the gas tank, the check engine warning light is triggered. After properly securing the gas cap, it might take a little while for the warning light to go off. Oxygen sensors.

Why is the engine light on on my 2003 Chevy Silverado?

I have a 2003 Chevy Silverado with a 6.0 engine and automatic transmission and the engine light came on. I put a scanner on it came up with the code po332B Knock Sensor 2 circuit low frequency. I need to know where the sensors are so I can change them out or check any wiring problems.

What should I do if my warning light goes off on my Chevy Silverado?

If oil level is low and engine oil was added, only continue driving if the warning light has gone off. Depending on your version of Chevrolet Silverado, you may receive the warning text message: ‘OIL PRESSURE LOW STOP ENGINE’. Stop the vehicle, switch off the engine and follow the above advice.

When you turn your key to the on position, all warning lights on the dash should come on. This indicates that they are working correctly (no burnt out bulbs, etc.). If the light comes on and stays on while the vehicle is running in the on position, that means you have an issue that will need to be addressed.

My rule of thumb is to run a tank or two of gas through the car once the light comes on. If the light doesn’t go off then I take it in. That many miles it most likely is one of the emissions control devices. Expensive to replace and do not really make the car run better. The other thing is, and I chase electronic problems all the time.

Keep in mind that the fault code that caused the light to turn on in the first place is stored in your car’s onboard computer, and you can retrieve it using a simple Bluetooth-powered device linked to an app to get a precise idea of what exactly is wrong under the hood. Doing this on your own will save you money.

When to use service engine soon instead of check engine light?

Some manufacturers use the service engine soon light instead of the check engine light when there is just a minor problem with your car and not a severe problem. It could also mean that it is time for a scheduled service, such as oil or spark plug replacement.

How to clear service engine soon light 1990 to 2002 Chevy?

Why does my check engine light not light up?

Why does the Check Engine light come on?

An electronic scan tool or diagnostic computer is used to indicate the problem, which is then mechanically addressed by a certified technician. The check engine light could illuminate for a number of reasons, the 5 most common being your: 1. Oxygen sensor needs replacing. This sensor tracks the amount of unburned oxygen in your car’s fuel system.

Is it safe to drive with the Check Engine light on?

It could also mean your catalytic converter has given up the ghost. The check engine light means there’s a problem somewhere in your emissions system. Regardless, you’re safe to drive for now as long as the car isn’t performing strangely. Just have the check engine light checked and the problem repaired.

Check engine light came on, stayed 2-3 days, then went of… Q: Check engine light came on, stayed 2-3 days, then went off. My check engine light came on out of the blue one day (12/14) I had my mechanic look at it immediately (the same day). He informed me that my thermostat was not keeping the engine at the desired temperature.

What does a steady check engine light mean?

Steady Light A steady “check engine” light means that one of the sensors in the vehicle responsible for the correct operation of the engine or other vehicle systems is delivering either no data to the vehicle’s computer system, or that the data is outside the normal range that the engine computer expects.

What should you do if your check engine light stays on?

If your “check engine” light is on steady, check to be sure that your gas cap is tight. If it stays on, you should take the vehicle in for diagnosis and repair as soon as possible, but your vehicle is generally safe to drive.

What does the Check Engine light in a Chevy Tahoe mean?

It is a source of curiosity for many drivers, who have different opinions about what it means when the amber-colored engine-shaped icon lights up in their vehicle. The “check engine” light in a Chevrolet Tahoe can mean many different things, depending on whether it is flashing or steady.

Why is my Check Engine light on steady?

Vehicle computers can often detect problems with electronic systems long before you may notice the problem with vehicle operation. However, the concern often grows worse over time. If your “check engine” light is on steady, check to be sure that your gas cap is tight.

Where can I find the Check Engine Light code?

Look up your code definition. This tells you where to start testing. If you are unsure of any abbreviations, check out the acronym list by clicking on the link at the left. Next, read our article Automotive Circuit Testing, and if there is an article related to the system you are testing, such as Oxygen Sensors or EGR concerns, read these as well.

Are there any problems with the 5.3 liter Chevy engine?

The 5.3 engine not only can succumb to engine sludge, but to faulty sensors. While this is a very common problem with this type of engine, it can be frustrating nonetheless. There are some quality oil sensors that will increase the performance.

Why is my 5.3 liter Chevy engine not working?

There is also the factor of environmental pollution which is also related to excessive oil usage. When you factor in excessive oil usage, the greenhouse gas increases rapidly, which then leads to pollution. Unfortunately, for many 5.3 Liter Chevy Engine owners, the cost to address this problem is too high in terms of labor and parts.

How to get rid of the ” Check Engine ” light axleaddict?

If it does not go off, then your engine has a problem. 1. Drive car and let light go off by itself. 2. Turn engine on and off three times in a row. 3. Disconnect and reconnet the battery. 4. Use an OBD code reader. 1. Drive Your Car and Let the Light Go off by Itself

How to clear check engine light and pass emissions test?

If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. I post about consulting, personal finance, and Texas life.

How can I get my Check Engine light to go off?

One of the possible ways of getting your check engine light to go off is pulling off the engine control unit’s fuse and then putting it back again. Although this won’t solve the problem in newer cars, it may solve the problem in a little bit older cars, and it is easy to try. Check your repair manual to find the fuse to the engine control unit.

What causes the Check Engine light to come on?

Once again, this can cause the Check Engine light to come on. With your engine off, check your spark plug wires for tiny cracks or holes, especially around the ends of the wires. If they look shabby, you should replace them. 4. Bad or Low Octane Fuel There are a number of cars that are very sensitive to misfires.

Is it safe to drive with check engine light on?

Sometimes, multiple sensors send signals, indicating clues that something bigger has gone awry. You can still drive with the light illuminated, assuming the car is running and driving fine, but you should get it checked out as soon as possible.

What do you need to know about vehicle backing?

• Use a spotter. A driver should use another person to help them when backing. The driver and spotter should use hand signals instead of verbal ones and make sure they understand each other’s signals. Don’t have the spotter walking backwards while giving instructions.

Can a check engine light be a problem?

If your car is running normally, and you have no problem driving it, the problem is not so severe that you need to panic. Of course you should not ignore the light; it is warning you of some problem with the emissions system.

How to get the Check Engine light on a Honda?

Honda Check Engine Light Codes 1 Connect SCS service connector special tool No. 07PAZ-0010100, or equivalent, to service check connector located under the passenger’s side of dash. 2 Turn the ignition on. 3 MIL will indicate DTC’s by outputting a number of flashes.

What does a Amber check engine light mean?

Check Engine lights come in orange, yellow or amber, depending on the manufacturer. If the light begins flashing, however, it indicates a more serious problem, such as a misfire that can quickly overheat the catalytic converter.

What to do if your check engine light is not flashing?

If the light is not flashing, check the gas cap. Oftentimes if the gas cap wasn’t tightened enough, the check engine light will display. If tightening the gas cap does not make the light go away, take the vehicle in to have the diagnostic codes looked up.

What does check engine light mean on 2014 Chevy Silverado?

A check engine light can indicate a broad spectrum of problems with your 2014 Chevrolet Silverado 1500. In some cases you need to pull over immediately to prevent damage while in others you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light.

What does it mean when your check engine light says gas is leaking?

If you get an error pointing to the gas cap, it means fuel vapors are leaking out of your cap. This means it’s either cracked or just wasn’t tightened well enough.

What happens if you ignore a check engine light?

Many think ignoring a check engine light will make one go away – instead, it’ll only make the underlying problem grow worse over time, that could eventually result in a major breakdown that requires significant time, money and effort to fix.